similar to: Cheap ISDN interface + Asterisk what to choose?

Hi All, The meetme.conf have created as below: [rooms] conf => 101 conf => 102 and extensions.conf as below: exten => _1XX,1,MeetMe,${EXTEN} why the warning printed when I called 101. WARNING[27660]: File pbx.c, Line 1051 (pbx_extension_helper): No application 'MeetMe' for extension (ipcentrex, 101, 1) And I found asterisk have not load the meetme.conf when it starts up.

Hi all, I have a cologne chip card which is connected directly to the ntba. Outgoing and incoming calls work fine, but incoming calls from ntba have the wrong callerid (first 0 is missing). I'm using current jolly misdn drivers and chan_misdn-14_04_05 with asterisk stable. Is anyone seeing this behaviour too? Thanks in advance Christian

Hi! I'm struggeling had to get a hfc pci card working in NT-Mode. I've installed a very basic test system with just one hfc pci card connected to an ISDN-phone over a modified NTBA as described on jollies homepage. I commpiled asterisk as descibed in kape's INSTALL file that comes with 'bri_stuff'. I have not modified the config fieles yet. After connecting to asterisk by

Greetings, asterisk list and community, I have a problem in how our telefon switch (Siemens HiCOM) "talks" with my new configured Asterisk server (V.11.18.0) without my Asterisks server in the middle.... <phone> <--> Siemens HiCOM <-ISDN-> NTBA <-...-> PBX Telekom A phone connected to the switch requests an "Outgoing" line by dialing "0".

hi all! I'm running an Asterisk-box with bristuff-....RC8n and 2 HFC-S cards. I m located in Vienna/Austria. I have the problem that on outgoing calls i hear my voice as a short echo (about half a second). This occurs not on every call. I tried some changes in my zapata.conf, with rxgain and txgain settings, but to me its hard to find a configuration which is good for every call i make. Is

so here it is, the problem that's been nagging me for the past 2 days: connected a box to my telco's NTBA <-> zap/asterisk. which works: box:/etc/asterisk# cat /proc/zaptel/1 Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" HDB3/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In

hi, i just found a page on the net which might me worth some lines. for the urgent reader: http://isdn.jolly.de there is a guy in germany who has successfully programmed a gpl-patch for isdn4linux to make isdn cards with the hfc chipset from cologne chip (http://www.colognechip.com) run in the NT mode (up to 2.4.20). this mode is needed to connect isdn device to a pc and enables the use of

I've this error How i can find the problem? Apr 23 12:24:43 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:47 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:48 WARNING[131081]: PRI: !! Got a UA, but i'm in state 1 Apr 23 12:24:53 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:25:02 WARNING[131081]: PRI:

I'm looking at experimenting with asterisk with an ISDN BRI and ISDN phones (since I have these already). I saw that the Billion card was cheap and could be used in either TE or NT modes. I have the following question which I couldn't answer by reading through the manual. Maybe someone has experience of using this card and can help me out. when using in NT mode does the card require

Hi there, quick question...do digium make any BRI cards (ISDN2) or even better a quad port BRI, maybe im going blind, but I cant see any on their website Cheers Gary

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

Hello everyone, I try to connect the Asterisk PBX Server on my NTBA (NT1) - actually its "hard"-connected on the box, but I've tried a crosslink-ISDN cable, too. My ISDN-Phone is connected on one port (of two) S0-Ports on NTBA. When I start Asterisk and want to make a call I'll geht a lot of this messages --> 040827-034639 WARNING[213005]: chan_zap.c:6902 zt_pri_error:

Hello, I have the following problem with HFC card and Alcatel PBX 4400: - I want to connect Alcatel PBX and Asterisk with HFC card (zaphfc driver 1port S0/T0 interface card) - BRI line is configured at PBX to T0 trunk - In asterisk I have loaded zahfc driver in NT mode and also set in zapata.conf NT mode, point-to-multipoint. - I am using cross "isdn" cable to PBX -

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hi, I need a ascii format of the type1 metric file (.afm) but I have a binary metric file (.pfm) only. Is there a way to convert pfm to afm format? -- Gruss Marcus Marcus Roeckrath -- Vikarsbusch 8 -- D-48308 Senden -- Germany Phone : +49-2536-9944 -- Mailer/BBS/Fax : +49-2536-9943 (V34, X75) FidoNet: 2:2449/523 E-Mail : marcus.roeckrath@gmx.de WWW :

Yes, i know that there are many ISDN card on the market. But when i spend money for ISDN card, i prefer to be Digiums, to get all support and help Asterisk :).

Hi, I am new to the Asterisk world. I don't know much about the architecture, but I am involved in installing and configuring the VoIP system. My requirement is to build a VoIP system using the 4 input lines (ISDN up0 telephone lines), it must be possible to receive calls from outside through the 4 ISDN up0 input lines, and also possible for outgoing calls, conferencing .etc. I

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: VoIP.gif Type: image/gif Size: 17666 bytes Desc: 1197705770-VoIP.gif Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20060213/7ca1c4ac/VoIP.gif

Hello All, Moving from 2.5 to 2.6.2 and I was wondering if there is a preferred directory structure for using multiple environments? Does it work much different in 2.6 than in 2.5? When I made the move I assumed (I know) that my current structure and configurations would just roll over but that isn''t the case. Thanks, Jim -- You received this message because you are subscribed to the