similar to: Updated Grandstream configurator

I've just finished a general purpose configuration utility for the GS phones: 1) Generates files from scratch (using MAC), from HTML config listing, or by directly downloading from the phone. 2) Does multiple simulteneous edits. 3) Can reboot as many or as few phones at a time as you like. I would like to offer it to the list, but there are 2 issues: 1) I want to GPL it first, if

I have Asterisk configured to record calls. Both in and out record ok but SoxMix fails to join the two files. The error from the CLI is as follows: Execute of ( nice -n 19 soxmix /var/spool/asterisk/monitor/Support-in.wav /var/spool/asterisk/monitor/Support-out.wav /var/spool/asterisk/monitor/Support.wav && rm -f /var/spool/asterisk/monitor/Support-* ) & failed. If I run exactly the

hi all i upgrade a bt100 phone and it can't resgister with asterisk Dec 1 13:25:49 NOTICE[1112980400]: chan_sip.c:7519 handle_request: Registration from '<sip:@172.16.4.249>' failed for '172.16.4.226' is was working with the version 1.0.5.3 some bady now what is hapening? thanks in advance Rodney

Three days after launching our * system with 20 GS phones, I have finally had to give up on dynamic registration. The phones keep dissappearing from the sip peers list, even if just sitting idle. Either I spend half my time re-booting phones to get them registered, or the extension appears busy to outside callers and people get really irritated. Even setting the registration interval to 5

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.

Hi Just recieved the above phone Does anyone have sip.conf and extension.conf example for the SIP phone working with the FXS w100p and the FXO tdm400d any help would be appreciated Thanks Robb

Does anyone out there know if it is possible to discover the dialed number when a line in an analog hunt group rings? I can't get a straight answer from our IT folks. We have a 5ess switch delivering 4 analog lines which are in a simple hunt group servicing our lab. I would like to have a different call attendant based on which number is dialed so that I can route the calls to the

If you wan't to create a ringtone with makering.pl for firmware 1.0.50, be sure to create it as ring.bin and then rename it to ring1.bin / ring2.bin or ring3.bin. This seems to be the only change between the format from 1.0.4.68. Regards, Maron

Hi All I have 3 GrandStream BudgeTone-100's which connect to an * box with a HFC-S based ISDN card using ISDN4Linux. I have setup the BudgeTone-100's to use Early Dial which for calling between the three phones works well, but for the external calls using the following extension exten => _9.,1,Dial(Modem/g1:${EXTEN:1}) Only the first digit is dial on the ISDN Line. Does anyone know of

Asterisk apparently has five echo cancellation algorithms: STEVE, STEVE2, MARK, MARK2 and MARK3. The current default appears to be MARK2. My question is, has anyone had any experience with any of the others (other than MARK2), and is there some conventional wisdom as to when to use one over another? TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

Hi, I have this scenario Cisco 5300 (public ip. 200.47.xx.xx) <---> Asterisk (public ip: 64.76.xx.xx) <--> Cisco 3600 (public ip: 64.76.xx.xx , same network than * ) When a calls comes in Cisco 5300, this send this calls with SIP to *, asterisk plays a welcome message and resend call to Cisco 3600 that have 4 analog lines connected... but after cisco play welcome message and when

Dear R users, I have two related questions about scoping and data encapsulation. One is fairly specific - I am looking at "scoping.R" which is used in demo(scoping) - it's an example of lexical scoping and encapsulation. Where is the 'total' stored? It is not an attribute in 'ross' or 'robert' however, functions like balance() have access to it. Is it more

Hello, I was just wondering if anyone's managed to somehow get MS IIS to run on Linux with WINE. If so, how did you go about doing it? Thanks. Bye, Fabio fabioa@subboard.buffalo.edu

Dear R users, I have a very simple question. What is the easiest way to recode data in one of the columns of a data frame and put it into a new column? For example, here is a simple data frame: var1 1 1 2 2 3 3 How do I add a new column to data - 'var2' in which I group values in 'var1', for example: var1 var2 1 1 4 2 2 4 3 3 5 It's got to

Does anyone have any views on the best software base SIP client to use that normal users could use with Asterisk without being too techie ? I have tried the X-Lite client with varying success. The first version worked OK but music on hold broke the voice paths and the slightly newer version initiated the call but failed to make the voice connect in both directions. The SJphone client works but

I am looking for a good analog desktop phone to use with asterisk and my sipura ATAs. I know I want Caller ID, MWI, a few programmable buttons (for asterisk features), and no external power supply (so my users can dial 911 through the SPA-3000 when the power is out). I spent some time looking at the phones at Fry's today, without finding exactly what I need. Do any of you have any

Dear R users, I am just starting with R (v. 1.0.0) and I use Vehables & Ripley's MASS book for examples. In the intro session, there is an example of a 2D histogram on an 8x8 grid: x <- rnorm(1000) y <- rnorm(1000) contour(hist2d(x,y,,,8,8)) R complains: Error in contour(hist2d(x, y, , , 8, 8)) : couldn't find function "hist2d" I looked for hist2d() in the

I know the recommendation it to not run more than 2 T/E100P's in a system but what about X100P's.. Usually there are 5 PCI slots in a system, has anyone tried 5 x X100P's in a system? Later.. -- ______________________________________________ http://www.linuxmail.org/ Now with e-mail forwarding for only US$5.95/yr Powered by Outblaze

Dear R users, I have to catch a nasty bug and would appreciate any advice or help! I get a segfault (core dumped) that happens in one of my own functions. The problem is, it does not happen most of the time, only sometimes, so it's very hard to reproduce. Or it may run ok in interactive mode, but bug out in batch mode. Also, it tends to happen more on the slower of my 2 machines (PII 266),

Hello, I would like to access my data frame without one variable. E.g.: > colnames(x) [1] "Besch" "Ang.m" "Arb.m" "i10" "Umsatz" "arbstd" I can try x[,-1], but this variable must be called by it??s name. x[,-"Besch"] x[,!"Besch"] attach(x) x[-Besch] ... ... does not work. I could not found a solution of