similar to: isdn to sip callerID pass

hello, i have a problem starting asterisk with one x100p digium and two hfc chipset isdn cards with bri-stuff.0.0.2. "ztcfg -vv" shows me a this info: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02) Channel 03:

hi, how to set caller ID for internal SIP users when dialing out on telco ISDN p2p (hfc card) line? I need to setup numbers from 0 - > 9 (10 sip users).internal caller id is working correctly .. from 0 to 9 ,but when I dial on isdn telco line -> gsm show only our prefix number ( xxxxxxY ) , only 6 (x) numbers of 7 (Y). here is extension 1 dialing on isdn line but on gsm is only 6

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

hi! Anyone on list has working asterisk box with hfc based card (bristuff) and a x100p adapter? Becouse together in box I can't get it working in any way .. thank you, Tomaz

anyone has idea what problem can be here, something with codec but i have today CVS version and grandstream phone with 1.5.0 firmware.I try to change codec in phone and also in asterisk-sip.conf but the same. What can be problem ? tnx, Tomaz *CLI> -- Executing Dial("SIP/102-767c", "CAPI/2:5") in new stack -- Called 2:5 -- CAPI[contr1/2003002]/0 is making

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN

hi, i just found a page on the net which might me worth some lines. for the urgent reader: http://isdn.jolly.de there is a guy in germany who has successfully programmed a gpl-patch for isdn4linux to make isdn cards with the hfc chipset from cologne chip (http://www.colognechip.com) run in the NT mode (up to 2.4.20). this mode is needed to connect isdn device to a pc and enables the use of

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if

Hello, After searching the archives, I''ve found only two messages regarding this case, but there were no solution. I have a similar problem, so I try to ask here. I have twi HFC chipset ISDN cards in my pc: 0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

I have a question, I have to provide a solution for an office that will be almost abandoned, and there will be one or sometimes two persons 2 days a week. The main number however should be preserved. They have several ISDN BRI connections, most of which will be dropped. Only one will be retained, for 2 reasons: 1) It has the ADSL link 2) The number has been the main contact number for over 20

Hi! I just wanted to ask if anyone managed to get "ordinary" HFC-S ISDN cards with the zaphfc driver running in a Xen3 DomU. I am referring to this post ( http://lists.xensource.com/archives/html/xen-users/2007-04/msg00202.html ), which perfectly describes my problem and I am therefore going to simply copy-and-paste it here: ----------- snip ------------> Hi, I''m

This is my first posting to the list. Thus hopefully the question has not been asked several times before... I'm trying to install asterisk on a PC using Debian Sarge but without any real success... Problem: I may get the Asterisk packet (Debian version) installed using 'apt-get install asterisk', but that does not include the bristuff from Junghanns

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

It seems so simple, but I'm having no luck installing a HFC-s ISDN BRI card on *@home 0.5. I probably have to install BRI-stuff from Junghanns.net but that also downloads and installs another copy of * from Digium. I'm not sure if zaphfc has to be installed *before* Asterisk or if it's OK to do this afterwards. I've seen this question before, but: Anyone successfully installed a

hi all! Is it possible to trigger some external device trough parallel port or. serial on some caller id ? or if it's possible tu run some external (linux) program on specific caller id ? OR if anyone have idea how to open the doors with asterisk :) by, Thomas

Hello everyone, I bought 2 HFC-ISDN Cards and want to run the first card in NT-Mode an the second one in TE-Mode. Everything looks ok under SuSE 9.1, but I can't dial out. I removed one card, for testing purposes and want to run this one card in TE-Mode. I only want to make a call with my Grandstream BT-101 over Asterisk via ISDN. When I try to make a call I get: ---------------------

Hi, I have built another Asterisk box using one ISDN HFC-S card and Bristuff-0.2.0-RC8p. But this time it behaves very strangely. Asterisk simply hangs and in logs I receive something like this: --NOTICE [1197]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 --NOTICE [1197]: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 And when I want to call a ZAP channel I get

I'm running * with a bog standard HFC ISDN card using zaphfc. Everything seems to work, including incoming calls, but I simply cannot make outgoing calls. This is very odd since the same card worked with the same configuration in another server. This is what I get from * debug. The only possible difference between the two servers that I can think of is that the HFC card is sharing an IRQ