Displaying 20 results from an estimated 600 matches similar to: "Zaptel, Line Impedence and Echo"
2004 Jun 25
2
Latest CVS fax detection & grandstream bug
As a follow up to my previous post, I have now identified what is
causing the bug with the grandstream phones.
When the line
faxdetection=incoming is in the zapata.conf file, the grandstream
phones will not ring, nor connect a call to the zaptel interface.
Can anyone else confirm this bug? I'm going to play with the different
options (incoming/outgoing/both) to see if it makes a
2004 Jun 24
1
Latest CVS, Grandstream and Zaptel bug?
Hi,
I'm confused as anything by this bug. I'm hoping that it is just
something screwy in my config.
I have 1 Cisco 7960 and several Grandstream BT101 & 102's, and a Digium
TDM31B.
I'm running the latest CVS (CVS-HEAD-05/27/04-17:22:40) of both
Asterisk and the Zaptel driver on Fedora Cora 1.
When I make an outgoing call on the Cisco phone, everything works fine.
I'm
2004 Jul 11
1
Echo issues (again...)
OK... so I'm not sure what I'm looking at. I've had the good old echo
problems on my Rev C FXO again this morning, so I thought I'd attempt
some debugging, though I'm not sure what I'm looking at.
This call has echo.
Channel: 2
File Descriptor: 20
Span: 1I>
Extension:
Dialing: no
Context: incoming
Caller ID string: "External Call" <99999999>
Destroy:
2004 Jul 07
2
Parking call problem
I been having a issue with call parking. I can park calls from internal
extensions. But call from the outside can not be parked. When I recieve
call from the outside I press the # key and nothing happens. Does any one
have any thoughts?
P.S. I am allowing the to be transferable.
James
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
2004 Jul 15
4
ZyXEL 2000W
Hi,
I know we've talked about this phone to death. I have pretty good voice
quality, with and without WEP enabled, using the G729a codec and DLink
& Netgear access points.
I am facing one obstacle that is driving me insane.
Does anyone have the call hold feature working? If you do... how did
you make it work? The instructions say to press the left button to
place the call on hold,
2004 Jun 24
5
chan_capi problem - hangup???
Hi,
I installed Asterisk with CAPI support. Everything works fine while
starting Asterisk, but when a call comes in Asterisk hangsup the call
after two times of ringing.
The output is like:
Jun 24 22:19:49 NOTICE[1082178480]: chan_capi.c:1931 capi_handle_msg:
CONNECT_IND ID=002 #0x011d LEN=0048
Controller/PLCI/NCCI = 0x101
CIPValue = 0x10
2004 May 23
3
NetJet and RAS
Hi,
Last weekend I was planning to buy a physical PBX system, but instead I
have been blown away by the fact that VoIP really works, that Asterisk
is so easy to set up and use... and free!
We're in Australia, so as I understand it, we aren't allowed to use the
Zaptel cards. We need to set up our system to route incoming 56K data
calls to the PPP daemon on our Linux box or to our
2020 Jul 24
4
Remove ANSI colour trings from log files only
Hi,
Is there a way to drop the ANSI colour strings from log files? In
particular, I've got JSON logging throwing logs over to ES, but they have
the ANSI colour escape sequences.
Ideally I don't want to lose coloured logs from the console though, and I
can't "see" a way to do this.
Ast 16 at the moment…
Andrew
-------------- next part --------------
An HTML attachment was
2020 Jul 18
2
PJSIP AoR vs Endpoint
Hi,
I realise this is an old question, but I’m struggling to get my head around
it.
The ERD suggests that endpoints can link to multiple AoRs
In what situation would you actually use this? Given that mapping of
inbound calls is primary done to the endpoint, it looks to me like most of
the scenarios where this might be beneficial are actually not possible?
One example I had envisaged was being
2004 Jul 05
7
Calling an outside phone number as part of a hunt
I'm trying to see if this is even possible.
When you dial ext 2000 I want it to ring my sip phone for 20 sec then
call my cell and let it ring for 10 sec if I do not pick up the call on
my cell I would like it to go back to * and leave a voice message for
me. Here is what I have so far in my extensions.conf
Everything works except the call will not go back to * after the 10 sec
rule has
2004 Jun 05
1
FXO answering quicker
Hi,
I don't know if this is possible - but can I set up asterisk to answer
the FSO line after one or two rings rather than four?
I haven't (yet) found a configuration variable to let me do this...
Thanks in advance,
Andrew
_________________________
Andrew Yager
Real World Technology Solutions
Real People, Real SolUtions (tm)
ph: (02) 9945 2567 fax: (02) 9945 2566
mob: 0405 15 2568
2005 Jan 09
1
passing opermode to the wcfxs module
Hi,
Has anyone in australia got asterisk running on FreeBSD? how would i
pass the opermode=AUSTRALIA parameter to the wcfxs.ko module as kldload
doesnt let you pass parameters to the module like modprobe in Linux.
I tried to get the sysctl variable using sysctl -a it might use but
nothing applicable was visible....
i need to set the impedences to 600 ohms, can someone please advice me
on
2009 Apr 02
2
opermode=?
Hi All;
If I need to set the opermode to King Saudi Arabia, what the name I have to use? For example, to set it for kuwait then I use opermode=KUWAIT. So what will be for Saudi Arabia?
Any advise?
Regards
Bilal
2004 Jun 21
8
Busy message
When I dial a SIP phone which is specified in the sip.conf, but the phone is
not connected, Asterisk gives the message "The user at Extension XXX is on
the phone ...."
Shouldn't the message be the unavailable message?
Is there something wrong with my set up or is this a "bug" with Asterisk?
Simon Brown
2011 Mar 17
1
[1.6] Where to put "options wctdm opermode"?
Hello
The Ubuntu Asterisk package doesn't install
/etc/modprobe.d/dahdi.conf, so I was wondering where to put the
following line:
=======
options wctdm opermode=FRANCE
=======
Should it be in /etc/dahdi/modules?
=======
options wctdm opermode=FRANCE
=======
Thank you.
2020 Jul 11
1
16.11.1 release removed from current
Hi,
This is not a big issue… I just noticed a build script that was pulling the
16.11.1 release from https://downloads.asterisk.org/pub/telephony/asterisk has
started to fail and went to investigate (I need to test a patch for a
bugifx). It looks like when the 16.12-rc1 RC was released the 16.11.1 was
pulled from the current release directory.
I realise it's probably better practice to pull
2013 Mar 11
2
Serviced Office operator panel
Hi,
I'm trying to find (with some desperation now) a decent web based or application based UI that integrates with an Asterisk based PBX and is designed for a Serviced Office environment.
Key features we're looking for:
Concept of a client with multiple staff/associates
Recognition of inbound DIDs with display of company details and greeting
Support for multiple receptionists
Some
2007 Mar 08
6
Empty Wildcard TDM400P as a MeetMe timer.
I've just moved into 3.3v PCI servers and found that my clone X100P
cards were lying about the 3.3v supported notch.
Can I use a Wildcard TDM400P without any modules as a timer for
MeetMe in a 64 bit 3.3v server?
Will I still need to plug the hard disk power cable into it?
Is there a better cheaper 3.3v MeetMe timer? (Boss doesn't trust the
kernel timer.)
-HJC
2020 Jul 22
4
Failed to authenticate device message
I am getting this message:
Failed to authenticate device <sip:2010 at X.X.X.X>;tag=149853321 for INVITE,
code = -1
but it does not report the "connecting" address. Who is failing connecting ?
I either need to block someone or fix something - I'm thinking block - but
I dont know who.
How do I found out the connecting IP?
Jerry
-------------- next part --------------
An HTML
2010 Nov 02
2
Ring Freq
Hi
I'm sorry for the my trivial quest.
I Have asterisk 1.4 with TDM 400 with FXO and FXS, and works fine from
several months.
Now I want to connect a device to TDMFXS that want a ring frequecy of
25 hz to activate: i am italian, and usually the ring freq is 20 hz.
The other time (I have used that device several times with other
asterisk installation) I have modified /etc//modprobe.conf and