similar to: Incoming IAXTel/IAX2 issue

I'm trying to make a call from an IAXPhone client - through the * PBX to an 888 number using the IAXTel link. I'm using the basic conf files for extensions and iax. I get successfully connected (at the "Attempting native bridge" line of the output) and am then able to talk both ways for 20 to 30 seconds and then the IAX phone appears off line. If I wait on the PSTN line for

G'day list, I am getting a lot[1] of traffic on my Internet link, ICMP messages from 69.73.19.178 telling me UDP port 5036 is unreachable (this IP address belongs to iaxtel.org). I see from the wiki that IAXtel supports only IAX2 from December 2003. Fine, however it looks like my * still wants to try and register using IAX1, and I can't find how to turn this off. This situation is

I created an account at IAXTEL.com to route 1-700-XXX-XXXX calls through. IAXTEL.com gave me a number (example) of 700-555-6226. I have made the following changes to my: /etc/asterisk/extensions.conf: [iaxtel700] exten => _81700XXXXXXX,1,Dial(IAX2/myusername:mypassword@iaxtel.com/${EXTEN:1}) exten => _81800NXXXXXX,1,Dial(IAX2/myusername:mypassword@iaxtel.com/${EXTEN:1})

I finally got around to signing up with Iaxtel and Free World Dialup... the price was right, as far as that goes! I've gotten and placed calls via FWD just fine. But I can't seem to get registered, or stay registered, with Iaxtel. My logs show the story; at startup I see: Jan 20 07:14:44 VERBOSE[14121]: -- Registered to '65.39.205.121', who sees us as ... yada yada... As

When I try to call iaxtel it goes to codec ADPCM even though I have define in iax.conf gsm Call accepted by 69.73.19.178 (format ADPCM) -- Format for call is ADPCM My settings: [general] port=4569 register => xxxx:xxxx@iaxtel.com bandwidth=high jitterbuffer=no tos=lowdelay [voipjet] type=peer host= xxx.xxx.xxx.xx secret= xxx auth=md5 notransfer=yes context=incoming disallow=all ;

I didn't get any response at all to my last "request for status" on IAXTEL. So, when this happens, I attribute it to one of a number of things: 1. No-one knows. 2. No-one cares. 3. Everyone knows, but are too busy to reply. At any rate, my investigative side kicks in and I began searching thru the digest's I've gotten, looking for references to IAXTEL. Mostly it is

Been meaning to ask this for some time... no big deal, but curious. I have a single register statement in my iax.conf for iaxtel like: [general] port=5036 register => npi:mypassword@iaxtel.com <snip> However, when I restart *, I see: Registered to '69.73.19.178', who sees us as 205.221.193.101:5036 Registered to '69.73.19.178', who sees us as 205.221.193.101:4569

Through my Asterisk server, I am trying to use IAXTel to dial 800-type numbers (yes, I know I can do the same thing with FWD and others via SIP, but I wanted to play with IAX a little). It appears I'm running into some sort of a codec mismatch or something because it's not working right. The SIP client is a SPA-3000. In iax.conf, I have something like the following: [General]

Hi there, do I have a local problem, or is registration at IAXTEL impossible at the moment? "iax2 show registry" permanently shows a TIMEOUT for 69.73.19.178. Philipp

Can anyone tell me why I keep getting these messages from IAXTEL? It does appear to register since I get lines like this: 2005-04-30 04:26:42 VERBOSE[1644]: -- Registered to '69.73.19.178', who sees us as 67.182.152.242:4569 But what is this? I don't think IAXTEL is working for me, since I can't dial 800 #s through it when I copy the iaxtel.com instructions. 2005-05-20

I've searched WIKI and Archives but nothing. Im getting: -- Called username:password@iaxtel.com/1800somenumber@iaxtel Jun 21 17:04:12 WARNING[1158883520]: chan_iax2.c:5097 socket_read: Call rejected by 69.73.19.178: Unable to negotiate codec -- Hungup 'IAX2[Iaxtel]/8' == No one is available to answer at this time -- Executing Hangup("SIP/104-b8eb", "")

[ Sorry, I incorrectly copied some Reference headers into this post and tacked it onto the wrong thread. -Steve ] So far, I have been able to receive incoming iaxtel calls via my assigned 1-700-xxx-xxxx number, but only when using md5 authentication in iax.conf: [iaxtel] type=user ; Incoming calls only context=incoming auth=md5 secret=<mysecret> ; Required for

After battling for days trying to figure out what was wrong with my iax.conf it was determined that I do not have any inkeys set on the digium server. Now whether that is something new or just in a few cases I am not sure. Messing around and reading on IRC and the mailing list I could get certain things to work and then break other things. Now I can dial a IAXTEL number, 800 number and FWD

Hi All, Sorry if this has been covered in the past; I've tried searching the archives, but haven't had any luck finding a similar problem. Basically I have problems when using IAX2 (which I now understand is just IAX). I have three IAX connections setup - VoicePulse, IAXtel, and an Asterisk IAX<->PSTN termination provider here in Sydney (ATP) If I try to use the CVS STABLE version

Hi i was trying to call 17009978275 which is my Fwd line on my notebook from Asterisk and i keep getting this message on the console. -- Executing Dial("Zap/2-1", "IAX2/@iaxtel.com/17009978275@iaxtel") in new stack -- Called @iaxtel.com/17009978275@iaxtel WARNING[1150495040]: File chan_iax2.c, Line 4547 (socket_read): I don't know how to authenticate rob to

Hi- let me start off by saying I'm a newbie to Asterisk and this list and I'll also apologize up front for stupid questions. I have Asterisk running and 2 SIP phones (X-Lite) plus an iaxtel gateway set up. I used the configurations from the O'Reilly article and I haven't even set up voice mail (the only change was to add the iaxtel entry). My problem is the audio out from my

Hi List, While trying to calling Toll Free numbers using IAXTEL, the call connects, I hear about 2 seconds of voice and then the voice drops off and I get the following error message which keeps scrolling across my console screen. WARNING[-167797840]: chan_iax2.c:5967 socket_read: Received mini frame before first full voice frame Asterisk shows that the format of this call is GSM. However if I

Hi, I've been setting up * recently and slowly getting to grips with it, however I'm getting rather confused with all the different configs for IAX calls, FWD calls iaxtel etc etc. What I think I need it a basic understanding or even a comparison of these different voip systems (if thats what they are?) I'd like to be able to make calls to other voip users, both in the UK and abroad

I have, in iax.conf the register statement: register => username:password@iaxtel.com This causes registration attempts to iaxtel.com for both IAX and IAX2. Every once in a while there is a packet for port 4569 keeping the IAX2 registration alive. This is fine. But, I have a barrage of registration attempts to iaxtel on port 5036 for IAX. Every UDP packet is answered with an ICMP packet

I tried to connect my * to IAXtel, but i always get this errors. chan_iax2.c:5849 socket_read: Registration of 'mnetwork' rejected: Registration Refused On dial a iax number i get: chan_iax2.c:5526 socket_read: Call rejected by 69.73.19.178: No authority found chan_iax2.c:5528 socket_read: Immediately destroying 3, having received reject chan_iax2.c:2411 iax2_hangup: We're hanging