similar to: tdm fxo users - new bug tracker entries

Has anyone made spandsp to work with a digium tdm fxo card? I finally got the rxfax and txfax modules to compile, the spandsp lib installed (and in the libpath), and now receive: -- Starting simple switch on 'Zap/1-1' -- Executing RxFAX("Zap/1-1", "/var/fax.tif") in new stack -- Hungup 'Zap/1-1' I've tried to adjust rxgain/txgain in

Good news! FYI, worked with Mark this afternoon to test changes needed to reduce or eliminate echo involving pstn calls on the new tdm fxo card (bug #1902). Three simple source code changes (testing-only at this point) resulted in zero detectable echo on all incoming and outgoing tdm pstn calls, even in the first second or two. I've not noticed any unusual side effects at all. Since the

A bit about my experience with the TDM-04 FXO. Only saw a few post on this subject, thought I would contribute a little about my experience to save others the hassle. a. As an earlier poster noted, the driver for the FXO is in the wcfxs module. Perhaps it should be renamed to something less confusing. b. You need the zaptel,zapata libraries from the cvs, the ones with Asterisk 0.7.2 won't

Hi Mary Christmas to y'all ! I am trying to configure * with one TDM and one ISDN and Bri-stuff, all is ok with only TDM but when add ISDN I get following error: I have tried to switch fxs/fxo but then I get error also without ISDN, card is configured from Digium with FXS(green) modules are closest to the bracket. ZT_CHANCONFIG failed on channel 1: Invalid argument (22) Did you forget

> > First, ensure the TDM card has been defined to match the telephony > standards for each country where the card is installed. Bad echo on these outside North America is likely to be because of impedance mismatch. Echo cancel isn't likely to properly fix it. I was surprised at the lack of info about setting up the TDM cards for various countries. I eventually worked it out from a

-----Original Message----- From: Gregory Wiktor - ADCom Corp. Sent: Monday, May 16, 2005 5:40 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] Static on TDM Zaptel FXO Hello, Yes in the bios I set unused irq's. Zttest is sporadic. This is a non HT cpu, on a standard ide drive. It is basically just a p4-2.4 with a single ide, onboard

Hi On an old IBM Netvista thinclient, the TDM card doesn't detect incoming calls, although the card seems to be detected, and correctly configured: pbx asterisk # lspci 00:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel

Hi, Have someone there tried the TDM 2400 with 24 FXO? Have had echo problems? or any other problem ? Recommendations? Optional echo cancellation modules are necessary? TIA, Fernando

Rich Adamson <radamson@routers.com> wrote: > >> I have been investigating on this list and found that faxing is not >> reliable between Zaptel >> cards and that Digium does not support nor >> recommend fax over the TDMXXB interfaces. >> >> Is this true ? Will fax not be reliable enough for my customer ? > > True... the TDM card (or its drivers)

FYI to the list.... I gave up (for now) trying to make spandsp work with the digium TDM card. Instead, I signed up with www.trustfax.com at a cost of $9.95 per year plus $.10/page. Since we only deal with an estimated 120 pages per year, the total cost of about $22/year seemed like a very reasonable alternative. (At least until we can find out why the TDM card does not function properly with

We're having issues with the FXO/FXS ports on our Digium TDM cards sporadically. I'm wondering if anyone else has had these problems, or if anyone can provide guidance diagnosing or fixing the issue? The symptoms are that the FXO and FXS ports "stop working", usually after 2-4 weeks of server uptime. When this happens, sending a (SIP) call to an analog phone on an FXS port

Hello all, recently i stumbled upon the I-TDM standard, e.g. see here http://www.picmg.org/v2internal/news2005.htm "SFP.1, also known as I-TDM (Internal TDM), is a companion protocol specification to SFP.0 that is optimized for TDM traffic over high-speed fabrics such as 1 and 10 Gigabit Ethernet (PICMG 3.1), Advanced Switching (PICMG 3.4), Infiniband (PICMG 3.2), etc. SFP.1 and SFP.0

Hi Is there a test that you can do to test your modules FXS FXO to see if they are blown I have a TDM400 with 2 FXS (green) modules on the the first two ports and 2 FXO (red) modules on the last two ports, but I can't seem to assign a channel to them. Can any one help me?? Thanx Jaco

Hi: I'm using a TDM-400 to terminate PSTN lines at my Asterisk server with kewlstart signalling. When an outside caller calls the server, the TDM-400 goes off-hook and provides a ringing tone to the caller. If the caller hangs up before the receiving party answers the phone, Asterisk fails to detect the hang-up. The TDM-400 stays off-hook, hogging the line, while Asterisk rings the

Hi, I'm experiencing an issue with my x86_64 machine containing a Hauppauge PVR-500 (ivtv) and a Digium TDM400p (wctdm, part of zaptel) PCI cards. Independently of each other both cards work fine, but once the wctdm driver is loaded and mythtv tries to record something on the PVR-500 the wctdm driver freaks out. The error message is see is "TDM PCI Master abort" printed over and

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

I sent a query about this before, but have some further information and am hoping somebody has a suggestion as to what to try next to debug this. I'm using an Asterisk box primarily for MeetMe conferencing. There are two sources: TDM via two Q.SIG T1's and SIP phones. Conferencing works fine between TDM channels. But when a SIP phone calls the conference, there's no voice path *to*

who can tell me how to do TDM over enthernet ? pc a connect pc b only use TDM card? thank you John. -----????----- ???: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]?? asterisk-users-request@lists.digium.com ????: 2004?12?23? 11:47 ???: asterisk-users@lists.digium.com ??: Asterisk-Users Digest, Vol 5, Issue 336 Send Asterisk-Users mailing list

Hi, sorry for my insistence but this is a big problem for me..my steps for remove card are ok ? Thanks. ------ Salvatore. ----- Original Message ----- From: "Sasa" <sasa at shoponweb.it> To: <asterisk-users at lists.digium.com> Sent: Monday, November 26, 2007 4:25 PM Subject: [asterisk-users] Remove a TDM Card > Hi, I would like remove a Digium TDM2400P from

https://bugzilla.netfilter.org/show_bug.cgi?id=351 Shane <arlenslambert at gmail.com> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |arlenslambert at gmail.com Attachment #134 is|0 |1 patch|