similar to: DID/T1

In Australia, Telstra, the local telco provides isdn modem for isdn connection. The modem has 2 analogue telephone jacks and a serial port for connection to dialup internet. My question is that will it be possible to use Zaptel TDM02B to connect to the analogue jack instead of getting a fritz card to do the telephony. Will there be less feature if doing so? -- David Kwok, CISSP Tel: 612

On Thu, 2004-01-15 at 19:18, dkwok@iware.com.au wrote: >> I do not have any zaptel hardware on the Asterisk box, I could not have >> meetme functioning. I did modify the Makefile in zaptel directory on >> line 168 by including ztdummy as one of the modules to compile in. try modprobe ztdummy This works. Should I include this in /etc/asterisk/modules.conf so that it will

I do not have any zaptel hardware on the Asterisk box, I could not have meetme functioning. I did modify the Makefile in zaptel directory on line 168 by including ztdummy as one of the modules to compile in. The error message from the concole: -- Executing MeetMe("SIP/1002-e9ca", "4700") in new stack == Parsing '/etc/asterisk/meetme.conf': Found

Chris Albertson wrote: |What firmware version do you have? program version 1.0.4.39 -- David Kwok Iaxtel/FWD # 17001813482 ext 1002 -------------- next part -------------- A non-text attachment was scrubbed... Name: smime.p7s Type: application/x-pkcs7-signature Size: 1878 bytes Desc: S/MIME Cryptographic Signature Url :

For people who are using GS 101, what do you think the sidetone generated by the phone. I find mind a bit annoying. It has a delay and you notice it as an echo. The volume of the sidetone is also quite hight. I am distracted when both caller and called party talking over each other occasssionally. The volume of the sidetone can be turned down using the volume button but it also control the

My ADSL connection speed is 512Kb up and 128Kb down. When making calls from Asterisk to IAX and back to the Asterisk, the sound is choppy and 20% of voice messages was lost. What is the production bandwidth requirement per internet call. I understand there is no guarantee of QoS but at least a benchmark to follow. -- David Kwok Iaxtel/FWD # 17001813482 -------------- next part

Just got GS 101 phone and plugged into the network. Got ip setup however, the following problems arise: 1. when dialing an extension, I cannot further send any key tone to Asterisk. 2. there is no sound coming from the other end. I have a sip.conf setup for GS: [General] disallow=all allow=ulaw allow=alaw [gs] canreinvite=no dtmfmode=info In the GS101 setting rtp port = 5004 sip port = 5060

Philipp von Klitzing wrote: > You'll need to provide the CODEC that you are using in X-Lite! > The codec used in Xlite is 711uLaw. I guess it is one of the preferred ones other than gsm. And it is of small size. -- David Kwok FWD#/IAXTEL# : 17001813482 ext 1002 -------------- next part -------------- A non-text attachment was scrubbed... Name: smime.p7s Type:

Subject: [Asterisk-Users] meetme not working Reply-To: asterisk-users@lists.digium.com I am trying to set up meetme functionality but am unsuccessful so far. When I dial the extension, an announcement says, "That is not a valid conference number, please try again." In order for meetme to work you need either zaptel hardware OR you recompile the asterisk directory and include the

I have 1 * box having x100p installed and the other has no zaptel card at all. both of the * box has compiled in ztdummy module and both have been activated by modprobe ztdummy. When using trunk to connect the 2 *box. The one without zaptel card complaint about unable to accept trunked packet: no matching peer. On the one has zaptel card I have tried to remove the ztdummy module and connect

Hi list, I'm with a little problem on codec negotiation between a cisco827 and asterisk. My sip.conf is like that: [general] port = 5060 bindaddr = 0.0.0.0 context = default amaflags = default allow=g729 allow=gsm allow=alaw allow=ulaw ;disallow=all and cisco like that: dial-peer voice 6 voip destination-pattern 0T session protocol sipv2 session target ipv4:<asterisk-ip>

I have problem to change from handsfree mode to handset mode. When I switch from handset to handsfree while waiting for connection I press the green speakerphone button once. It is all well. Once it is connected I don't want to give the called party too much echo and I want to switch it back to handset. If I press the green button again I lose the call. Anyone knows whether it is possible

I have been experiencing hung up when answering incoming calls through x100p. NOTICE[1242768320]: chan_zap.c:4584 ss_thread: Got event 2 (ring/Answered).. -- Executing Wait("Zap/1-1","1") in new stack -- Executing Answer("Zap/1-1","") in new stack -- Executing DigitTimeout("Zap/1-1"."5") in new stack -- Set digit timeout to 5 --

I have looked at matt's asterisk gui client at sourceforge. I am not a programmer by trade. The documentation there seems to be a bit lacking. Has anyone have the experience in installing the gui client and may perhaps have a how-to document available for sharing. -- David Kwok Tel: 612 99292086 ext 1002 Iaxtel/FWD # 17001813482 ext 1002 -------------- next part -------------- A non-text

What are the meaning of these Zap show channel output? Caller ID string: Owner: <None> Real: <None> Callwait: <None> Threeway: <None> Confno: -1 Propagated Conference: -1 Real in conference: 0 DSP: no Relax DTMF: no Dialing/CallwaitCAS: 0/0 Default law: ulaw Fax handled: no Pulse phone: no Echo Cancellation: 0 taps unless TDM bridged, currently OFF Actual Confinfo: Num/0,

Hi Everybody, Got a weird problem here I think. Got a setup with an asterisk (current from cvs as of a few hours ago) in a box with an el-cheapo ISDN BRI card connected to the PSTN network and two Snom phones internally (one Snom-100 and one Snom-200). Dialing between the snom phones or dialing out to PSTN from any of the snom phones works perfectly. But when I receive a call FROM the PSTN

In relation to voice degradation when having 2 or more connection to Asterisk. The comment on the network setup is quite possible. I am not too familiar with linux. How do I check whether the asterisk server's nic is running at full-duplex mode. Does Asterisk use the sound card on the box to do voice processing? I am running xlite on 2 pc and making calls through iax, FWD and back to my

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

Snom 200 has be set up with extended key pad. The product literature also mention multiple sip registration. How many registration can it handle? It does not seem to appear in the user manual. David Kwok