similar to: CFDA from cell phone to SIP line in Asterisk PBX

Is anyone successfully using the AGI script calleridnamelookup.agi (or anything similar) ? I get both name and number caller ID from my POTS line, but I'd save money if I had them deliver ANI only. I've downloaded and installed the AGI script calleridnamelookup.agi, but I always get -- Executing AGI("SIP/9525485560-5359", "calleridnamelookup.agi") in new stack

Hi folks, I want to fix hole in my asterisk set up. I use Vocal as my sip proxy and * for voice mail and the g/w to PSTN, Iconnect, fwd etc. So from Vocal I redirect sip requests which needs to go 'other' places. This senario works fine. Now the issue is someone else running a vocal or another SIP proxy can redirect his calls to my * as well. Those calls two will come through general

Hi, I am calling from a grandstream phone with g723 codec through * to iconnect. Incoming context as well as outgoing context set to g723.1 codec in *. Call get connected and I can talk. However I get the following warning, which scrolls on my screen until I hang-up. [root@asterisk sath]# cat g723.1 - Executing SetCallerID("SIP/-08122ae0", "1001") in new stack --

Folks, I have to admit that I MAY have changed something (at someone's advice) on a previous CVS head (May 28), but I'm not sure. I think that it had to do with changing "digest realm," but that may be a different issue. At any rate, I had both incoming and outgoing with iConnectHere. Now, I made exactly ONE change: I upgraded to the CVS head dated 7/30. I

I have an asterisk Redhat 9 box running 4 hardphone extensions. Inter-extension calls are crystal clear. However when I dial out through my iconnect account I get a lot of jitter. At first I thought it was my nat gateway but after I programmed on of the hardphones (budge tone 100) for direct dial to iconnect I have clear voice transmission. I have no way of explaining this. My asterisk sip.conf

Hello, Recently I am seeing this message on my asterisk console received from Iconnect. Apr 30 11:37:21 NOTICE[1125329600]: chan_sip.c:5648 handle_request: Unknown SIP command 'NOTIFY' from '213.137.73.41' It is prety annoying as it appears once every four seconds. I've seen similar posts in the archives which points me to NAT keep alives being send by the remote end. I am

This appears to have been the magic bullet for me. Thank you very much. So, the bottom line is that there is a bug that ends up making inbound calls use type=peer rather than type=user. Correct? > -----Original Message----- > From: asterisk-users-admin@lists.digium.com > [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Paul Cheng > Sent: Tuesday, August 10, 2004 8:35

Symptoms: when calling my iconnect phone number (13033913323 in my bogus example below) from my cell phone, I can see that the call makes it to my asterisk server, and my phones even ring once as * passes the call through during the "180 Ringing" period. However, it seems that iconnecthere.com cannot see my "100 Trying" and "180 Ringing" messages, as they

Hi there, Since last 2 days iconnect's incoming is not working. Is it the same with everybody? For the past 5 months I've been using this service perfectly in two boxes and suddenly it stopped functioning. I'm able to call out, the version is 0.9.1. Any help is appreciated Thanks, Raj --------------------------------- Do you Yahoo!? New and Improved Yahoo! Mail - Send 10MB

I assume that from your previous post that you are using iconnect Is your register line in the format: Register => 18005551212:1234@213.137.73.178/18005551212 I've had good luck using the IP address vs. the fully qualified hostname. Remember that the register line goes in the [general] section of sip.conf. Also, are you using the latest CVS release of *? -----Original Message-----

I'm having a big problem where digits dialed from certain cell phones are too short to be recognized by my asterisk server. I'm running AAH 2.8. Some cell phones don't allow the caller to hold down the digits and have the tones play as long as they hold them down for. They just play a short tone no matter how long you hold down the digits for. Has anyone run into this before, and if

Hi, I'm using a Cisco ATA186 and iConnect to complete PSTN calls to the US. I've noticed that when I set the Cisco ATA to use LBRCodec to 0 (g.723 instead of g.729), AudioMode 0x00150015 and RxCodec, LxCodec to 0, (use g.723) Asterisk will connect to iConnect, successfully natively bridge the call and then about two seconds later not just drop the call, but terminate unexpectedly.

Hello all, I have a 7960 registered to asterisk. I am trying to use iconnect as my sip provider. When I send an invite to delta-three, I get the normal INVITE - 407 - INVITE exchange. The problem is, asterisk is sending the second invite using the 'dialed number' from the 7960 as the username, and not my 'username' configured in sip.conf. I believe that digest authentication

Hello, Don't know if this is related but I just got a segmentation fault today while trying to register my new SNOM200 phone: *CLI> *CLI> NOTICE[1125329600]: File chan_sip.c, Line 4713 (handle_request): Registration from '<sip:mattf2@10.10.10.15>' failed for '10.10.10.14' NOTICE[1125329600]: File chan_sip.c, Line 4713 (handle_request): Registration from

Hi, I wish to connect several ATA186 Phones to each other, to iconnecthere and to the PSTN using asterisk. Please tell the appropriate settings for firewall (ports to open etc.) sip.conf and extensions.conf(part relevant to iconnect). Also I would be glad to get a working example of your ATA186 configuration. I tried searching the mailing lists and several sites but did not find an answer.

Hi, I was able to connect asterisk to iconnect's service. It took me almost two hours, but it's because I was having NAT trouble. I finally discovered that you can set the iconnect host to natrealy.deltathree.com to make it work. (for those of you who, like me, don't have the time to search the archive I'll provide a working sample in a minute) My problem was sound

Hello, is anyone on the list using a normal cell/mobile phone which is able to act as a SIP client over WLAN? Or has anyone heard of a SIP client for cell/mobile phones running windows mobile 6.x? The phone should use SIP, when the asterisk server is reachable and should automatically switch to a German telco if it is not reachable. Thanks for any hints, Stefan --

A while ago SIP transfer via the # key on a call to a cell phone via iconnect was working. I updated to the current CVS tonight and now that functionality is gone. Any ideas as to how to enable it again? Thanks in advance -russ

I set up a context to allow me to call in to my * server (via Teliax in this case using IAX2) from my cellphone, and let me do a number of things, including dial other extensions, AND dial outbound again so callers could see my proper work CallerID when I use this service. Is there a way to be able to transfer calls to other extensions of my asterisk server FROM the cell phone/ This isn't a

I set up a context to allow me to call in to my * server (via Teliax in this case using IAX2) from my cellphone, and let me do a number of things, including dial other extensions, AND dial outbound again so callers could see my proper work CallerID when I use this service. Is there a way to be able to transfer calls to other extensions of my asterisk server FROM the cell phone/ This isn't a