similar to: miserable time with Cisco ATA186

I have spent the morning on this project, still without success. Summary: Yesterday I inadvertently unplugged my Grandstream phone. I might add I did a rebuild of my s/w from CVS at the same time. Since then, the Budgetone seems to talk SIP just fine, but the RTP being sent to it by asterisk "doesn't make any sound." It was suggested I do a factory reset of the phone, which I

I have an IconnectHere account with a Inbound number and have setup the sip.conf to register and am recieving the call but When I answer the call it disconnect. I have tried sending the call to from * to a Softphone, Pingtel, and FXS port and all result the same. As soon as I accept the call it disconnects. I believe it may be some type of codec issue but I am not very familiar with that layer.

Hi guys, sorry to be iterating this on the list once more, but I'm not able to get this stuff to work as I'd expect. So far, I've always managed to keep it out of NAT environments :-> My home LAN is NATed by a simple Draytek router. In the home LAN is an ATA186 with SIP. On the internet (public) is an Asterisk server. I have nat=yes in the sip.conf and the connectmode is set

Using DIAX softphone which seems to be working OK can get to VM/echotest etc in the demo context Am trying to setup FWD but get the following problems Can hear it ringing when dialing FWD no 612 for time. Connects but no sound from remote end. Does anyone have any suggestions. Softphone on 192.168.0.2 asterisk on 192.168.0.3 Netgear RP114 doing NAT to the internet port 5060 being forwarded to

Hi All I seem to have a small problem with the music on hold button on SJPhone. I have 2 asterisk installations one from the Rapid distribution and one from the latest CVS. On the rapid dist when I press the music on hold button on my SJPhone I get music on hold. When I do the same I get no music on hold just silence. I create extension like this exten => 1111,1,MusicOnHold(Default),

Hey all! I'm having problems trying to set up an ATA 186 with my Asterisk box. When I get the phone to place the call, I type the extension and I only get busy signal after 5 seconds. So I can't call my Asterisk box from my ATA and either call from my Asterisk to my ATA. Does anybody know what can be happing? Log is attached.. tks regards Oz -------------- next part -------------- >

I just downloaded the newest version from CVS(Tuesday@~7pm) and I am getting an error whenever I call the asterisk box. I cannot here any audio on the budgtone. This works fine with my pingtel phone and my sip 7960. Also if I call my Skinny 7960 it rings but I get that same error when I pick up. When the skinny phone calls the Budgtone it works fine. I have 2 budgtone phones and it does this on

Using AMP, the configuration I have used to work fine with Broadvoice. Now it gets a busy signal every time. I've checked "sip show registry" and it says it's registered just fine. I've tried "sip debug" and it shows calls coming in, but they always get a busy signal & I can't tell why. Here's a SIP Debug output: Sip read: INVITE

Hi, I've one Sipura SPA2000 at home behind a linuxbox with two network adapters (eth0 for WAN and eth1 for LAN) doing NAT/DHCP: ___________ HOME _______________ ____OFFICE ____ SPA2000 <---> Linux Box <--> Asterisk Box 192.168.0.253 192.168.0.1 eth1 200.93.xxx.a 200.93.xxx.b eth0 My problem is when I try to call to any trunk or extention

I am unable to get a my Draytek working with our Asterisk server. I can make/recieve calls but get no audio. I have tried the various codecs at the Vigor end but still getting nothing. I looked at sip debug (below) but am new to Asterisk and don't really know what I am looking for. Asterisk works fine with XLITE so I know my installation is ok. Sip read: INVITE

I am configuring a sip-phone, receing calls, excellent voice quality. but it does not place calls, please, can some one sort out. here is my debug output, and below that is sip-debug, Jul 16 11:34:32 DEBUG[163850]: Setting NAT on RTP to 0 Jul 16 11:34:32 DEBUG[163850]: Stopping retransmission on 'iiasPlzFribMJMcW' of Response 1: Found Jul 16 11:34:32 DEBUG[163850]: Setting NAT on RTP to

Hi I request your help because i don't have actually a solution at my problems. I have a Asterisk Server in 1.6 Connected at a SIP Provider This provider supply me 2 numbers: 003318364xxxx (official number) 081169xxxx (Nddi Number) When i receive a call on the 081169xxxx, he don't use the extension. He use the 003318364xxxx extension. SIP Debug: <--- SIP read from

Hi all, I am struggling to make my asterisk server work. The problem is I can not place a call from a phone outside, but I can call out from a phone in the local network where the asterisk server sits. I turn the debug on, and the log are shown below. I can see "REGISTER" method is OK. ( SIP/2.0 200 OK) But Later, in the "INVITE" method, the SIP addresses become

I'm using the Debian Sarge package of Asterisk - 1.0.7 + bristuff. When I call from a zap channel or a SIP phone to another SIP phone, then dial *8 from a third SIP phone, I get 503 Service Unavailable on the third phone and I get this at the Asterisk console: Jun 28 09:01:24 DEBUG[16774]: res_features.c:1709 ast_pickup_call: No call pickup possible... Jun 28 09:01:24 NOTICE[16774]:

On 2003-04-08 at 09:42, Mark Spencer wrote: > > So audio should probably be cut through as soon as dialing is finished. > > We do pass audio through whenever we get 183 Session Progress (or even > without it). However, in at least one users tests, interfacing with Cisco > equipment, the Cisco is sending to the wrong port number (not the one we > specified in our SDP) so

Hello. I am in a strange situation. I have two asterisk. Asterisk "A" makes a call for asterisk "B" by IAX. Asterisk "B" recives the call and delivers it to Openser by SIP. The problem is openser printing this in the screen: ERROR: parse_to : unexpected char ["] in status 5: <<"David" <sip:>> . ERROR:parse_from_header: bad from header

I have 2 sip accounts setup - 200 and 202. If I do sip show peers I get: sip show peers Name/username Host Dyn Nat ACL Mask Port Status 202/202 192.168.0.6 D 255.255.255.255 5060 Unmonitored 201/201 (Unspecified) D 255.255.255.255 5060 Unmonitored 200/200 192.168.0.3 D 255.255.255.255 5060

Hello All, I've spent a day trying to get a Polycom IP500 wokring with my Asterisk box. I have several others that are working fine, but this one is getting by me. Can someone on-list tell from the following SIP debug what I've missed? Sip read: INVITE sip:2000@192.168.1.30:5060;user=phone SIP/2.0 Via: SIP/2.0/UDP 192.168.1.37:5060;branch=z9hG4bK51f01c8152912F0E From: "2004"

im having a strange problem related to call-limit for peers. well im not sure if its related to call-limmit or not. Bottom line is: I call a user A, from user B. user B hears silence, untill it goes to voicemail. when user B hangsup. user B's call limit is reset to 0 but user A's call limit is not reset.strange thing is user A's status on cli is shown as NOANSWER, while user B did not

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm setting up an Asterisk system which is connected to an Alcatel 4400 PBX. On the * I permit g729 and gsm as codecs. If I try to transfer a call by hitting the # key, I get this messages and nothing happens on the phone: WARNING[30110]: codec_ilbc.c:175 ilbctolin_framein: Huh? An ilbc frame that isn't a multiple of 50 bytes long from