similar to: Billing and CDR's

Hi guys, i've installed asterisk to handle multiple voip accounts. I've looked at CDR configs, and managed to have cdr-csv files growing after each call. It would be easier to check my locak asterisk cdr's than logging into each account and check them at the provider website. i found that if i ring my sip softphone from my ata, bill seconds are counted correctly. however, if i

I've installed a TDM400. Having a go with AMP. I would like incoming calls to be put throuhg to an extension (at my desk) and a mobile (cell phone) at the same time. Whichever picks up, gets the call.. This should be possible with AMP (call groups, 200|201|0*0408xxxxxx), but it didn't work, so I have created a custom-incoming in extensions-custom.conf What is happening is, The extension

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi Joseph, I've resolved this problem for myself by changind the order of lookups : $>cat /etc/nsswitch.conf group: pgsql files passwd: pgsql files .... but it'd be a good idea to compile add the ncsd (nis caching daemon). then the file will look like this group: cache files pgsql etc... as far as I looked at the code I think the problem

Hi all, I am having a curious problem. I use two cdr backends, csv and MySQL. These are my settings: Call Detail Record (CDR) settings ---------------------------------- Logging: Enabled Mode: Batch Log unanswered calls: Yes * Batch Mode Settings ------------------- Safe shutdown: Enabled Threading model:

Hi guys, I would llike to ask for your help on a problem I'm having with the cdr functionality. I installed asterisk 1.0.4, and asterisk-addons-1.0.4 and followed the procedures for installation and mysql configuration. Everything seems fina. The cdr_mysql module is loaded, and I get no error messages. But the cdr's are not going to the mysql database, they are going to a csv file in

Hi, I just want out find out how to do bill recon's when you send calls to a provider. They send me their CDR's, and when I compare it to my * CDR's, some calls are 1 second off, either way. How in general is it done by others? -- thanks, Yusuf

We just installed a box into a Melbourne site with a Sangoma A101U, it is running the latest Wanpipe drivers and has Asterisk on it that someone had compiled manually from source. This initially worked fine but for the sake of consitancy we removed the existing asterisk and used emerge to install it. During this time the box was off of the e1 for about 8 hours and when it was brought back

Do any of the Australian Telstra users have some working tx/rx gain settins for the Sangoma cards on Telstra that I can try, echo is acceptable but not perfect using 0/0. I will also post them onto the wiki. Regards, Andy

On Monday 19 June 2017 at 18:12:35, Sebastian Gutierrez wrote: > use replication 1. Agreed - use replication. 2. If you want an HA (High Availability, not dependent on a single Master DB server replicating to a slave) solution, consider setting up Master-Master replication, with an LVS (Linux Virtual Server) HA machine in front of the two, so that writes can go to either server using only

List, Does anyone know how to add the dst Country to the CDR's via Macro (preferably). For example, I will add a column in the cdr DB table and when someone dials 01158212XXX. I want the CDR's to show Caracas as the destination in this new column. I have all of the International destinations in my extensions.conf like the example below: [macro-dialout-intl] exten =>

Hi there, How do i setup asterisk, so that in the CDR's is only the time, which the line actually was connected? Not the time, the line was up, but the time the user was able to talk to another user. Thanks in advance, Carsten

Hello all. Can you help me find where the CDR's are being stored? The result of "cdr show status" is: Call Detail Record (CDR) settings ---------------------------------- Logging: Enabled Mode: Simple Log unanswered calls: No * Registered Backends ------------------- (none) Best regards, -vcf

Hi. I'd like to get the call-id from a call (the *C-0000061c* part) to set in on a field on cdr's, like [Oct 8 16:09:37] VERBOSE[25701][*C-0000061c*] app_queue.c: SIP/12234-00006b18 is busy [Oct 8 16:09:37] VERBOSE[25701][*C-0000061c*] app_queue.c: Nobody picked up in 0 ms [Oct 8 16:09:38] VERBOSE[25843][*C-00000622*] netsock2.c: Using SIP RTP CoS mark 5 ... same =>

Can anyone recommend a call accounting solution with rating for post paid billing that works well with asterisk using the account code or any other info from the CDR? I don't want the billing software to any phone calls for me, therefore any solution that modifies my extensions.conf is out, nor does it have to allow for customers the ability to log in to check their usage/balances. I have

Hi All, PLEASE READ if you depend on Asterisk CDR's and support transfers. Apologies for the shout but I'm desperate to get others to agree Asterisk has a big problem with the CDR's that are generated for transfers. I can understand why not too many people are interested as transfers are complicated and messy. However for those of us having to support transfers and depending on

Hello, Rather than rely on a set of IF statements (as there could be many - please see below)), could the following be done in a different/better way? InternalMean <- mean(data1[,3]) if (InternalMean == 0) Intresult = 1 if (InternalMean > 0 & InternalMean < 1) Intresult = .95 if (InternalMean >= 1 & InternalMean < 2) Intresult = .85 if (InternalMean >= 2

Telstra (Australian Telco) has recently introduced a feature to allow the sending of SMS direct to fixed analogue lines, with an appropriate handset. As best as I can figure out, this appears to use CID type signalling, or at least on a line that otherwise has no CID on it, CID is sent, but with a standard modem I can only receive the date, time, and phone number (eg normal CID info). After that

Hello all, I would like to get billing/charging informations of all outgoing calls of any PSTN numbers made with my IP-Phone via asterisk. Can I obtain in * an accurate charge information of outgoing call via CAPI which destination is any PSTN number? Does the ISDN "signal" contain charging informations ? Thank for advice Rastislav

Hello; I've been playing with a nifty Open Source java based report writer called Datavision (datavision.sourceforge.net) and I've managed to write enough logic to calculate phone bills at different rates from the MySQL cdr's. (cdr_addon_mysql) Eventually I want to have sets of rate structures for each user of the system - so I can bill client A at 3 cents a minute and client B at 2

All; I know that there are probably several solutions to this problem, but what I am trying to do is provide some redundancy for my customers CDR data. I know that doing simple backups of MySQL is probably the easiest way to go, but I'm thinking that there may be some benefit to simultaneously writing the CDR data to multiple servers at once. However, I'm drawing a blank on this one.