similar to: Using Ser and Asterisk together

Do some reading about contexts in *. Basically, you want all "public" sip requests to land in a dialplan context that has no access to PSTN, and requests from your own SER box(es) to land in another context (that DOES have access to PSTN). You can achieve this by adding an entry to your sip.conf for your SER box with it's IP address (and context) specified. ----- Original

Asterisk is an excellent PBX system, and makes a very good endpoint in the SIP chain for all sorts of things -- IVR systems, voicemail applications, automated messages, etc. It has an extremely well-written CDR engine, so many people mesh it with billing applications to produce accurate accounting information. It also is fully aware of the media stream, which means it's capable of cutting

Any more ideas on my below mail? If a user is registered with SER and leaves a voicemail message with asterisk (by using rewritehostport etc in ser.cfg), then how is the user supposed to listen to the message afterwards? Is there any other way other than the MWI method?? Thnaksm Aisling. ---- Original Message ---- From: ashling.odriscoll@cit.ie To: asterisk-users@lists.digium.com Subject: FW:

What's wrong with ARA (asterisk realtime architecture) from voip-info: Asterisk, SER and MWI http://mail.iptel.org/pipermail/serusers/2004-December/013727.html Actually I wrote a patch for this and it supports ast_data too. What you do is tell asterisk that all of your phones IP addresses are your SER machine. Then when a message gets left Asterisk sends the NOTIFY to username at

Hello, I try set Ua---SER----Asterisk (voicemail/ARA) | Ua ser stable asterisk cvs head I read http://mail.iptel.org/pipermail/serusers/2005-February/015997.html to forward unavailable or busy sip agents to asterisk voicemail in failure route. How may I configure extensions.conf and ser.cfg ? I have been trying without success! Regards Harry

Hi, As many of you may know, we are undertaking several tests in order to test the interoperability between several PBX IP from different vendors. Until now, we were trusting that the VoIP IP PBX were good enough to be interconnected directly, however, one of the vendors have presented the "SBC" concept. The "SBC" (Session Border Controller) is not a new concept since we

Dear All, I have the following setup. Quad T1's<->Asterisk (PBX)<->(LAN<->DMZ)<->SER<->(Firewall)<->(Internet) | Local US Help Desk (Snom 200') This setup works well. I can pass calls from over the internet to the Asterisk PBX via SER using X-Ten Lit. I have a couple of questions; 1. How do I

Hello to all Im using X-lite, eyeBeam and Cisco 79XX phones and I would like to know the best way of implement a centralized address book system. Maybe the solution is LDAP, but these clients doesnt seem to support LDAP.Who should contact the LDAP directory? the SIP clients or the SIP server? Thanks Joao Pereira

I am running Asterisk and would like to add SER to register my (sip) DID and connect it to asterisk; but I'm not sure if this is the correct forum. I have as DID, sip account with one VoIP provider; currently I"m using just stand alone SIP phone and register with the VoIP provider via: stun.fwdnet.net Is it possible to use SER to register with the provider and forward the call

Hi all, I was wondering if someone could explain the relationship of Asterisk, SER & Jabber (XMPP) to me. I understand that there are facilities within Asterisk to use jabber to notify of incoming calls via XMPP clients, however I'm trying to work out exactly where the SER server would sit in all of this and what it's actual role would be. This might seem like a silly

Greetings, As a developer and consultant who spends considerable time on projects involving the fusion of Asterisk and products derived from the SER ecosystem (OpenSER, Kamailio, OpenSIPS, the new SIP-Router), I have found that there is a great volume of interest in this topic on the mailing lists associated with all communities involved, but a comparative lack of focus that results in

Hi All. I'am using Asterisk with SER. I can make call between two internal VoIP gateways or from na internal to external VoIP gateway. But when I get a external call, this call hang ups 5 seconds after and I reveive the following messages *CLI> -- Executing Dial("SIP/16008-3d17", "SIP/16007&SIP/16006|20|tr") in new stack -- Called 16007 -- Called 16006

is it possible to register asterisk in a sip proxy as if it were a terminal (like a cisco ATA)? how? Thanx Jenna ;) ___________________________________________________________ 1GB gratis, Antivirus y Antispam Correo Yahoo!, el mejor correo web del mundo http://correo.yahoo.com.ar

Hi, I've just read the postings regarding the interworking between * and SER. As these persons seem quite knowledgeable on this, I would like to have their advise on my planned installation: - I have broadband cable access - I plan to install a SIP-aware router - I plan to install a Linux server with Digium analog IF card(s) for connection to my analog line (incoming and outgoing) - I plan

Anybody out there use Ser along with *? Any advantages disadvantages? Is this even a good idea?

Hi, I have some trouble with the Monitor() application. I start and stop it via the management interface, giving no special parameters except the channel name. What happens is: - if I specify WAV as the format, the resulting files are exactly 44 bytes big and contain nothing at all - if I specify GSM as the format, the resulting files are of size 0. I did not request mixing of the files or

I know FWD uses a SER/Asterisk combo, and I keep hearing about the massive benefits, however, my initial playing around in SER's configuration indicates it's NOTHING like Asterisk at all, and almost 5x as difficult to understand and configure. But that's only after a few hours of playing with it. I'm interested in learning SER more, especially the integration with Asterisk. Is

Sorry it's asterisk-users@lists.digium.com --- harry gaillac <gaillacharry@yahoo.fr> a ?crit : > Luca, > > you may find help here: > > http://www.cs.colostate.edu/~somlo/CSU-SIP-notes/ > http://www.asteriskdocs.org/ http://www.voip-info.org/tiki-index.php?page=Asterisk+at+large > > ask for help to asterisk-users@lists.digium.org > > Regards >

I install ser and found my ser don't support mysql. my ser version : ser-0.8.14_src.tar.gz and ser-0.8.14_linux_i386.tar.gz who can help me? thanks. Best Regards Zhao Zigang ??? Alcatel Shanghai Bell Co., LTD *:388,NingQiao Rd.,Shanghai 201206 *:086-21-50554550-7762 *:Zigang.Zhao@alcatel-sbell.com.cn

Hello Robert, Ser, Asterisk, Mysql and Freeradius are working fine , I'm feeling tired with CDRRTool . I will use an other billing system. Thanks for your answer. Regards Harry --- Robert Zorop <rzorop@gmail.com> a ?crit : > HI, i've got a working config of ser 0.9.6, > freeradius, MySQL, and CDRTool > 4.5.3. I can't get the quotaCheck script working, i > think