similar to: UIP 200

Does anyone have any recent news on the Virbiage FT201 IAX Hardphone? I'd *really really* like to deploy these phones instead of SIP hardphones, and I can't help but wonder if I'm going to shoot myself in the foot (or another sensitive area) by deploying a ton of SIP phones just to find the IAX Hardphones were released a week later... Thanks, Brian D'Arcy

Folks, I'm looking for a SIP or IAX phone for field techs to take with them when out on service calls. The regular desktop phones are just way too big. Is there anything like the size of a full-sized cell phone? Or smaller, not I doubt that... Tim --

Hi, I'm new to asterisk, and have a uniden UIP 200 that I got off of ebay. I'm having trouble getting the phone to register with asterisk. I've tried a few different settings. I'd be extremely grateful if someone with a similar setting could give me the sip.conf block for the UIP and the settings you're using in uniden.txt. Here's what I have currently: IP of phone

Hi everybody i have a problem trying to connect an incomming phone call from pstn to my (soft phone) iaxcomm, the phone rings but when i try to answer the call, asterisk sends a message like this. Jun 1 19:33:17 NOTICE[5013528]: channel.c:1223 ast_read: Dropping incompatible voice frame on IAX2[192.168.222.99:4569]/16 of format GSM since our native format has changed to ALAW i'm working

It would be a real kick to get one of these to run Asterisk. :) http://www.gumstix.com/ Tim -- >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>

Stutter tone when voicemail in boxHi, I'm having a problem getting Asterisk to make a stutter tone when a voicemail is received. It used to work, but since I rebuilt my server I can't get it going. I've set put a line in the sip.conf file: mailbox=100 to check it, but it's not doing the stutter tone ! I am using the stable version of asterisk from the CVS tree. Any help /

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

Hi - I'm wondering if any has experience with the Uniden UIP-200 phones. The product info says that the 8 led buttons at the top are all programmable. Can they be programmed as separate line appearances (ala Snom 200, Cisco 7960, Zultys Zip4x4, etc)? In other words - is the phone capable of multiple SIP registrations? Also, the post about these phones at voip-info.org mentions some

Hi, We've recently deployed 6 Uniden UIP200 phones (running firmware 4.54). We've been having some serious problems: 1) All the phones randomly reboot themselves. Typically when trying to answer or initiate a call. 2) All the phones will disconnect from a calls with the PSTN after 2-3 minutes. 3) The phones are unable to interact with a remote IVR (digit presses are not received at

Folks, It seems like the * v 0.9 and iaxcomm won't speak to each other. Is there another IAX2 client that is usable under Linux (Debian preferred)? Thanks, Tim --

I just got my wife this phone, and when calls come in on the queue it will not ring, if I dial the ext it rings, here is the config from the tftp server: Thanks unidencom.txt # UIP200 Mass Configuration System Generic File # Notes: # 1. Lines start with '#' are comments # 2. To leave a field value unchanged (as saved on local phone), leave value to blank. # 3. To set a field's

No kidding, every time. I know I have the config via tftp working. Funny story - I was getting nowhere with it and then decided to tcpdump on the tftpd box, and wow! The UIP-200 tftp client was looking for the uniden<mac>.txt in lower-case! Hah! That was easy to fix. Now the config is transferred to the UIP-200 at startup. It registers to the * server. The phone displays time and

Hi All I have a snom 200 phone here which works perfectly when using the handset to playback the voicemail messages etc. However when I play back the voice using the speakerphone it sounds choppy. Anyone had this problem before? Regards Mark

Has there been any luck getting the 3Com NBX series phones to work with Asterisk? Thanks! -Andrew

I am looking for a large number (probably about 100 or so) low-cost phones that I can hang on the wall. I need the phones to use PoE. Do the Uniden phones support wall-mounting? These phones are not going to be high-usage; they simply need to be there in case of an emergency. Another question, along the same kind of lines, has anyone figured out how to keep the SoundPoint IP 600 receiver

These are the three cheap SIP phones that I've used. Grandstream BT10x $65/street Number only LCD Zultys ZIP 2 $100/retail No LCD Uniden UIP 200 $120/retail PoE, built-in switch -- Eric Wieling * BTEL Consulting * 504-899-1387 x2111 "In a related story, the IRS has recently ruled that the cost of Windows upgrades can NOT be deducted as a gambling loss."

I am having a really hard time getting gnophone working with asterisk. Gnophone tries to register with my server but there is no response. I can direct incoming calls to gnophone but if gnophone answers them, asterisk does not recognize it. Here is my configuration: iax.conf [jambo] type=user host=dynamic defaultip=136.159.99.100 permit=136.159.99.100 username=jambo secret=fubar

I had a working system using * 1.0 and then 1.2 and now Asterisk 1.4.13 with addons 1.4.4, zaptel 1.4.6, libpri 1.4.2. I have a mix of Grandstream (GXP2000), Uniden uip-200, Linksys Wireless G, and analog phones via Adtran chan bank. When I went to * 1.4.13, the Uniden phones stopped being able to login to voicemail. All phones are on same lan with Asterisk. I get 'Login incorrect'

I just purchased 30 of these after testing one for a few months and would like to quickly purchase another 40. We really like these phones: good sound quality, good echo control (no echo in speaker phone), power over ethernet support, 10/100 switch, 8 programmable keys. Unfortunately we missed on big problem with Call waiting in our testing. When using asterisk 0.9.1 or rc2 the phone will reboot

I just spent the last hour or so trying to get this firmware to work across a NAT with no success. I have a GS BT101 working through the same NAT, so I don't think it's the NAT itself. I have a STUN setup in * and pointed the UIP200 to it and I tryed several combinations of nat= in the sip.conf and in the config files for this phone. No luck(yes, I did a reload now with each change in