similar to: TDMoE hangs the machine

Hi all, I'm having some problems getting TDMoE setup for the 1st time. I have a TE405P installed in the main server with an ethernet cross-connection to the secondary machine. (Yes, I know about IAX2 but I want to use TDMoE to simulate using T1s.) I'm using -HEAD from yesterday. On the main machine /etc/zaptel.conf: loadzone = us defaultzone=us

Anybody sucessfully got stable 1000Hz clock without Digium harware and kernel 2.6? We need to consult some peoples how to clock asterisk stable with exactly 1000 Hz without much kernel/drives patching/tweaking. Some test results we made so far: 2.6 with digium card - stable 1000 Hz. 2.6 with ztdummy - uses RTC and the clock is 1024, not 1000. 2.6 with some Realtime kernel patch - provides stable

Anybody have any issues running tdmoe on kernel 2.6+? I've got Suse 9.1 + 9.2 running 2.6.5 and 2.6.8 respectively, and when I enable dynamic spans between them, both boxes dump something similar to: Badness in local_bh_enable at kernel/softirq.c:141 [<c0120768>] local_bh_enable+0x48/0x60 [<c02952b0>] dev_queue_xmit+0x230/0x240 [<c02a0980>] eth_header+0x0/0x140

I'm just experimenting with dynamic spans using TDMoE, which looks ideal for clustering Asterisk boxes with low latency (i.e. 1ms for TDMoE compared with 20ms for IAX). When using normal E1s and T1s, I've always used ISDN signalling: either EuroISDN or NI2. So naturally I tried that over the TDMoE. I've found that I get a lot of HDLC errors and the D-channel is up and down like a

I'm scoping out HA for a relatively simple Office/Call Center PBX. Current setup uses a TE412P with 4 PRI our telco with SIP hard/soft phones for users. Some outbound also goes to a SIP provider. Active/Active looks to be too much hassle for an installation this size, so we're looking at adding an extra * in an active/passive configuration with Linux-HA in between them. Does anyone

Hi, I have just begun working with TDMoE running between 2 fiber nics the dynamic span works great. In my main asterisk box's startup file I just 'modprobe tor2', then start asterisk. The zaptel, ztdynamic & ztd-eth modules all load by themselves when tor2 is loaded. If I stop asterisk then 'modprobe -r tor2' the tor2 module is removed but the other three remain. If I

In all the information on Asterisk it takes about TDMoE to link asterisk servers together. Is this IAX??? How would I use TDMoE. Maybe my first question should be, What is it??? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030516/cd74bddb/attachment.htm

Hello, I want to link several * boxes together. Some of them are dedicated as "user" servers (SIP and IAX clients connect to them) and some are used as PRI servers (where the PRIs are hooked onto). I think TDMoE is the only channel type where you can group different Interfaces into a single group. E.g. for using Dial(ZAP/g1/12345), I think you cannot group different IAX accounts

When I was trying to run mutiple E1s over TDMoE, the zaptel would drivers complain about too little memory, whenever I added more than 31 channels. Requesting 62 channels in a dynamic span gave me ... span creation failed: Cannot allocate memory upon loading the zaptel drivers. How would you go about running, 8 or 16 say, E1s over TDMoE? Would you create multiple dynamic spans or just one large

I've been experimenting with the zaptel TDMoE stuff and I've got it all working. Calls go from one asterisk box to the other, with no issues, except they don't bring the callerID along with them. I tried the e&m signalling from the wiki and I thought maybe that had something to do with it, so I just changed it to half fxsks and fxoks and that didn't help me any, I still

Robert, > Is there a product to simulate a PRI trunk? (Robert > Goodyear) TDMoE emulates a T1. ;) Once the TDMoE link is up, Asterisk just sees 24-lines that appear to be a T1 instead of having to deal with all of the complexities of VoIP. This is useful, since probably 75% of the utility of VoIP is really just the fact that it can run over a network. It's also handy because it

I am planning to configure * box A with PSTN interface to route faxes to * box B (running spandsp) over TDMoE. I am using 2xGb bonded NIC's for connection between servers. Was wondering - does anybody have experience with TDMoE over bonded interface - ie. does it work ok?. - does anybody have feedback using this scenario for fax? another question, perhaps someone knows what's the

Hello, I want to create channel bank in this case: "channel bank" |-----------------------------------------| | FXS,FXO<----->TDMoE<--|---------------------------------->Asterisk |-----------------------------------------| How can it?

Hello, I've been using TDMoE accross 2 * boxes for months. It was working well, but * would crash when anyone would try to connect via h.323. So, I got the latest CVS release and compiled without h.323 support. After I made and installed the latest CVS the TDMoE channels stopped working. They have been working great (especially after we got echo cancel working them, thanks Mark) and the

Hi All, Please bear my ignorance but what is TDMoE used for? Illustrations with practical applications, scenarios or set ups will be most appreciated. Thanks Luan

If I have a system with 1 machine to handle incoming H.323 calls and then multiple machines to distribute them to T1 ports over TDMoE, where does the codec translation take place? Does it take place in the master system or does it take place in each of the slave TDMoE systems? Also, any idea how many concurrent G.729 calls a system like this would handle?

Hi all, Information on this topic seems a little scarce, so I thought I'd try the list.... Apart from the the coolness factor can anyone explain to me in what situation one would use TDMoE rather than IAX for communication betwwen 2 Asterisk servers?

We have been pretty much able to solve our echo problems, except for the primary mode in which we desire to operate our system. See system diagram at bottom. Prior to making adjustments to cancel echos (all echocancel=no): Call Type Result (Before) --------- --------------- CP <- LEC PRI * TDMoE * FXO -> AP

Just a Question. I would like to know if TDMoE follows specifiaciones of TDMoIP RAD protocol that says that there is a compression of 16/1 when you do TDMoIP. Manuel Marin Garcia TRANSTELCO S.A. DE C.V. Campos Eliseos 9050 B4 – Cd. Juárez, Chih. 32452 - México Oficina: +52 656 692 11 09 – Fax: +52 656 692 1112 - Celular: 915 727 6141 http://www.transtelco.com.mx

I was trying to establish a TDMoE span of 4 channels between two Asterisk servers. Machine A has a T100P to our PBX. Machine B has no Zaptel hardware. With 4 channels (e&m signalling) the red alarm never clears, and eventually machine A panics. With 24 channels, the TDMoE span seems to work perfectly. Is this hardcoded somewhere? I don't really need a full 1.544 Mbps between my two