similar to: Multiple ISDN controllers & Capi

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

I've having a big problem after having upgraded to 1.2.4 and chan_capi-cm 0.6.4 When making outgoing calls I don't seem to have any control over the CLI that is presented to the called party -- it can be any one of the MSNs allocated to the line, allocated on what seems to be a random basis. This is on a BT Business Highway line (which is essentially an ISDN2e line with two built-in

Hello all, I'm trying to setup a AVM C2 card. I have read the kernel requirements for this card. <M> CAPI2.0 support [*] Verbose reason code reporting (Kernel size +=7K) [*] CAPI2.0 Middleware support (EXPERIMENTAL) <M> CAPI2.0 /dev/capi support [*] CAPI2.0 filesystem support <M> CAPI2.0 capidrv interface support My problem is when I make a "make

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute

Hi, I've a Fritz card which was working fine, recently I changed hardware and my nightmare started. Now when I call someone through the chan_capi (0.3.5 or 0.4.0) it works fine but when I receive calls I always get hungup. Can someone please give some help? Here are the logs: *CLI> -- CONNECT_IND ID=001 #0x0000 LEN=0049 Controller/PLCI/NCCI = 0x101 CIPValue

Hello, I'm using asterisk 1.0.7. with a somewhat advanced setup with IAX and CAPI as channels. A call comes in via IAX2 and should be redirected to CAPI. So I wrote the following dialplan: [fromiax] exten => _8XXX,1,Answer exten => _8XXX,2,Dial(CAPI/265:B${EXTEN:1},,r) [fromcapi] exten => 265,1,Answer exten => 265,2,Dial(IAX2/PoC/11@from-lw) exten => 265-BUSY,1,Busy exten

I have 10 msns on my isdn bri incoming (AVM Fritz, chan_capi 3.5) When i set in capi.conf [interfaces] msn=1,2,3,4,5,6,7,8,9,10 incomingmsn=* controller=1 softdtmf=1 accountcode= context=tcom-in echocancel=yes devices=2 Only msn 1,2,3 are working. What can i do? Thanks Jens

Hi, I was trolling through the archive to see if it was possible for asterisk to ignore certain MSNs. I have a AVM Fritz/BRI with two MSNs: 7770001 and 7770002. I would like asterisk (with chan_capi) to ignore 7770001 such that a regular phone on the bus will ring; calls for 7770002 should be picked up by asterisk. I configured msn=7770002 incomingmsn=* within capi.conf and figured this would

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hello, i wonder why i didn't find a solution for this problem yet, because it seems very common: I have an asterisk server with an AVM (Fritz) ISDN-Card (BRI), and some SIP-Softphones which i can call from outside by calling the phonenumber of the Asterisk-Server and then dialing the number of the SIP-Phone. If I make a call from a SIP-Phone into PSTN, only the MSN of the asterisk-server is

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

Hi folks! Is it possible to tell asterisk not to strip the leading 0 of *incoming* MSNs? I use asterisk with i4l and whenever I get a call from an long-distance party, the leading 0, which should be there according the german numbering, is not. So if I get a call from a mobile phone 0177-1234567 should be displayed, but 177-1234567 is displayed. I double checked if I've forgotten to remove an

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi list, I have a server running a simple hfs isdn card running with chan_misdn. the problem is, I can't get asterisk to pick up the phone, outgoing calls work fine. when running asterisk with -vvvvvvvvvvvc I get the following "log" when I try to dial the isdn server. P[ 1] * Starting Ast ctx:kpn-in dad:0594643637 oad:0878722291 with 's' extension P[ 1] MGMT: SSTATUS: