similar to: MGCP: Current CVS works for you?

I have a SwissVoice IP10S but can not seem to get it to have dialtone or dial on *. Calls to or from 3001 don't work. Any ideas are appreciated. Robert mgcp.conf is: [general] port = 2427 bindaddr = 192.168.0.110 [ip10] host = 192.168.0.5 context = from-sip line => aaln/1 The portion of extensions.conf is: exten => 3001,1,Dial(MGCP/aaln1,20) exten => 3001,103,Hangup

I have set up a new SwissVoice phone and it can receive calls but I cannot make calls out from it. The setup is simple for now, 2 phones: SwissVoice is ext 7726 and Cisco 7960 (SIP) is ext 7999. I can call from the Cisco phone and it rings on the SwissVoice phone but when I dial from the SwissVoice phone I get a busy tone upon dialing the second digit. The log reads as follows: -- Endpoint

Hi there, after testing with a MGCP phone (Swissvoice ip10s) I found the following ASTERISK-based codes (VERTICAL SERVICE CODES) to work - I assume that most of those will also work with SIP, but haven't checked that yet: *67 - Calling Number Delivery Blocking *70 - Cancel Call Waiting *72 - Call Forwarding Activation *73 - Call Forwarding Deactivation *78 - Do Not Disturb Activation

Hello, Now that I have a nearly working configuration for my IP10S with * I wonder if anyone has done call transfert with this Phone. In the IP10S documentation they talk about the 'service key' wich is the key with the white dot on it. With this Key, it should be possible to have a menu with call transfert entries. This menu should (accordingly to the documentation) depend on the

hallo, does anybody successfully managed to get swissvoice ip10s with h323 firmware work with asterisk ? mgcp firmware works fine, but with h323 i'm still getting one way audio. regards Marian -- SUNTEQ s. r. o. Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic Tel: +421-46-5430 754 # Fax: +421-46-5439 144 http://www.sunteq.sk/

Has anyone had success getting the Swiss IP10S and the SIP ( IP10 SP v0.0.1 (Build 4)) firmware working with Asterisk? If so do you have copies of what worked in sip.conf and phone configuration files? I can't seem to get the phone to register, it tries but is denied with a Forbidden (which I am guessing is authentication). I tried without a secret, but the phone seems to use swissvoice

taken from bug 881 (now resolved) :-( ---------------------------------------------------------------------- markster - 05-19-2004 09:21 CDT ---------------------------------------------------------------------- As it turns out the 10S cannot conference on the device. From Jean-Francois at Swissvoice: Hi Mark, IP10S have not the capabilities to mix by itself 2 RTP flows, that why it refuses

Hi there, here some questions and experiences after playing for one day with 3 Swissvoice ip10s and the latest * CVS: QUESTIONS: - what is the user option "enter voice mail number" good for? It doesn't appear to be of any practical use - does anyone have some Swissvoice info that I cannot find on their web site like the guide to MGCP XML (.svd), guide to configuration file

I have 1 IP phone (Swissvoice IP10S) and 1 POTS phone. When I dial the number for the IP phone off the POTS phone, the IP phone rings. But when I pick up the handset on the IP phone, I get a busy signal and this message on *: Aug 23 09:38:57 NOTICE[1142106560]: chan_mgcp.c:2243 handle_response: Terminating on result 502 from svip10@00059002042b-1 Here is the entire session. svip10 is the 1 and

Does MGCP transverse NAT? Seeing as the only decent yet cheap IP phone is the Swissvoice, it would be rather helpful.

I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below I go off hook

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes

Hi Does anyone have a howto on how to set one of these up on Asterisk or Trix box please? I can make it SIP or MGCP so whatever you have ;-) I have found one page but it isn't really a howto setup Thanks in advance Paul -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi. I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk with the next configuration files. '--------------- extensions.conf ---------------------------------------------------- [general] static=yes writeprotect=yes [globals] ap1 => mgcp/aaln/ap200@64.76.148.186 [macro-apl1] exten => s,1,Dial(${ARG1},30,Ttmr) ;exten => s,2,Voicemail(u${MACRO_EXTEN})

Funny - I downloaded the latest Asterisk CVS, and it's pretty much working. Will report when I have some more success. PaulH -----Original Message----- From: Philipp von Klitzing [mailto:klitzing@pool.informatik.rwth-aachen.de] Sent: Tuesday, 28 September 2004 9:46 PM To: Paul Hales Subject: Re: [Asterisk-Users] Leader IP10S Hi! > I have been lent a Leader IP10S phone (SIP) for

Hello, Sorry for posting again my question about MGCP Phone and Asterisk But I can't use it. I'd like to know weather it is a pb of my confiuration (mgcp.conf), My IP Phone device or asterisk. I include my mgcp.conf file and may send some debug trace. Thank you for any feedback. Best regards, Daniel ANDRE ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr =

Hello there. What I'm trying to make is - have an asterisk server with sccp/mgcp/skip/h.323 support to handle calls between various company locations. Let's say the company has five different locations, internet connections in each one of them and would like to use it via asterisk to do telephone calls. Hardware-wise I have a couple of dual Opterons and some classic i386 servers

Hi I've a mgcp fon (swissvoice IP10s) behind a NAT router. Configured is NAT for both in/out going on port 2427. Now I got the following mgcp debug messages when i try "mgcp audit endpoint <endpoint>" ---------------------------------- from 172.16.98.57:2427 Verb: 'RSIP', Identifier: '5346', Endpoint: 'aaln/1@[192.168.2.3]', Version: 'MGCP

Hi folks I seted up the asterisk with an active ISDN B1 AVM Card (german vendor) and it works fine, various SIP clients (IP fon snom, xlite under MacOSX) and also incoming and outgoing connectins. Ok. No problem. After that I configured a CP7940G with a MGCP IOS. It's connected to the asterisk too via switch. No NAT deivce between. And of course, I can call out to PSTN and also to one of the

Hello, I have just received an MGCP Phone for test purpose and I can't place a call from my MGCP Phone. I can call my MGCP phone from a SIP Phone. Here is my mgcp.conf: ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr = 0.0.0.0 ;[dlinkgw] ;host = 192.168.0.64 ;context = default ;line => aaln/2 ;line => aaln/1 [192.168.10.10] host = 192.168.10.10 context =