similar to: Cisco 7905 and as5300 + Asterisk

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

Hi all, I realize this is OT. I just got a Cisco AS5300, and I need to configure it like such: Asterisk -----(H323/SIP)------> Cisco ----- (E1/PRI)------->Telco So calls originate from the Asterisk side (registered users on SIP or just ZAP phones), and they go out H323 or SIP to Cisco, where they go out PRI. I have the Asterisk side sorted :) (either H323 or SIP), I need help in the

Hi, I had previously posted about connecting an AS5300 to * via SIP/H323. I got it to work via SIP, but only 1 call at a time would work, and if a user from the * side hung up, the cisco would'nt catch the hangup. I an now trying to hook up to the cisco via E1, with a Sangoma A101 card in my * box. I would like it such that I call from * via E1/PRI to the cisco, and call out via R2 to

Hi i'm trying to connect to the PSTN in the following way sip ATA -> * -> gnugk -> Cisco AS5300 -> PSTN I'm using asterisk CVS-HEAD-06/01/05-14:33:15 running over RH EL3 Asterisk-Oh323 0.7.2 pre1 Open H323 v1.13.5 pwlib v1.6.6 and I'm having a lot of trouble, gnugk and * both have public ips and are not behind any type of firewall, the sip ATA is behind a firewall and

Hi Now, my Cisco AS5300 sent call to my asterisk, but two problems: When i call the phone number, i have: [Oct 28 06:01:16] NOTICE[12813]: chan_sip.c:18160 handle_request_invite: Call from '' to extension '0426000000' rejected because extension not found. [Oct 28 06:01:18] NOTICE[12813]: chan_sip.c:18160 handle_request_invite: Call from '' to extension

I wouldn't expect you to be using RFC3389 if your using A-law, can you include your IOS version and IOS config file ... I have not specified any allow's or disallow's in my * config for the codecs with my 5300, I also use Cisco 79xx phones and I use the option within the phones config file to select the preffered codec and when I change this to G.729/A-law/U-law all works perfectly

Hi I have finished the installation of my VoIP basic configuration ... Actually: - All calls from my E1 are received by a Cisco AS5300 and sent to my Asterisk (in G711 by SIP). - All user are connected by SIP to the Asterisk - All calls from User are sent by asterisk to the Cisco AS5300 Now, i want see if i can supply T38 Fax Gateway .... I am search to: - Cisco Receive all

Hi to all! I have this config, PSTN <--> AS5300 <--> ASTERISK I am using the Cisco as5300 to receive incoming calls and routing them to Asterisk for IVR. When I ran asterisk this is what I get when calling the voicemail demo. *CLI> -- Executing Playback("SIP/-081058b8", "transfer|skip") in new stack -- Executing Macro("SIP/-081058b8",

Hello, I have a Cisco AS5300 connected to Asterisk (1.6.2.9) Between 15-16 minutes, the call is disconnected without reason. Here is what is displayed in the debug: Received an SDES from 10.4.0.10:17399 -- Got SIP response 420 "Bad Extension" back from 10.4.0.10 -- Stopped music on hold on SIP/as5300-1-0000004d == Spawn extension (dialin, 065939191, 2) exited non-zero on

Guys. I need some advice on some h323 issues. I need to test connectivity from Asterisk to a Cisco AS5300 that has PSTN lines and to cisco 3600 voip routers. H323 needs to be used here but I was wondering if anybody has linked Asterisk to these Cisco routers before? Thank you for any pointers.

I have my server configured to send to send all PSTN traffic to my Cisco AS5300 gateway via SIP. I use the following line in the extensions.conf file to accomplish this: exten => _NXXNXXXXXX,1,Dial(SIP/1${EXTEN}@10.1.1.1,240,T) Unfortunately, when I removed the T from the end of the statement, the calls still complete, but they drop as soon as the called party answers the phone. I thought

OK, here goes my next problem. I have puchased a DID which I can connect to via SIP I have been given the following details: Username: uka1xxxxxx Password: 1000xxxxxx Server: brxxxx.net:5160 My equipment is Asterisk CVS HEAD on Red Hat EL 3.0 (NO NAT) The other end is a Cisco AS5300 (NO NAT) I can register with the Cisco with no problem. When I dial the DID it sends the call to my asterisk

Hi, We need help in enabling g729a codec for our SIP peer that's using Cisco AS5300. Our codec is purchased from Digium. We are able to dial out the numbers and answer the call, but there's no audio. This is when only g729a is allowed. We noticed when they also allow ulaw codec on their side, the codec used falls back to ulaw and the problem is gone. -------------- next part

Hello, I have 5 digium's g.729 codecs and succesfully register with asterisk, I have incomming call from my cisco AS5300 to Asterisk through IP. But Asterisk always use g711 ulaw instead of g.729. When I disable all other codecs other than g.729 in both cisco and asterisk, calls get dropped once connected. The codec list show on my cisco AS5300 for g.729 are: g729r8 g729br8 I suspect that

Hi all, I have a Cisco 7905g with the default cm firmware. It is connected to * using chan_sccp.so. Normal operations with this phone work perfect. Now I'm implementing a click to call app in php. This php app connects to the manager interface and sends the following down the line: $this->_write($fp, "Action: Originate"); $this->_write($fp, "Channel:

Hi, I'm using a Cisco 7905 (with SIP image CP7905010300SIP050414A) on Asterisk 1.07. Whenever the user gets voicemail, the MWI goes on, and when the user listens to the voicemail, the MWI goes off. However, the phone is configured (as in the default config by Cisco) to re-read its configuration from tftp every hour. This 'warm reboot' also turns off the MWI, and it won't

Hey all, I have an as5300 I use for dial in customers, we have 4 PRIs on it. We have a few free channels on it. I'm wondering if I setup SIP on the as5300 I can have asterisk use the free channels for dial out. I'd still have to use my TDM04B for incoming calls, but at least I can expand my outgoing. Anyone done anything like this before? I've never messed with VoIP on Cisco

I am trying to send calls from an AS5300 to Asterisk via e1 and I get this bit of information in place of routing information Going to extension s|1 because of Complete received Accepting call from '' to 's' on channel 1, span 1 Here are the relevant zaptel and zapata pieces. span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 signalling=pri_cpe switchtype=national

I'm deploying a fairly large number of Cisco 7905 with SIP connected to an asterisk PBX. The problem: the 7905 has this nice "feature": You can set a "voice mail number" in configuration, so that you can listen your voice mail just by hitting the "messages" key on the phone. It just autodials "8500" or whatever else. The customer wants this, so

How to disable silence suppression (or Voice activity detection - VAD) on Cisco 7905 phone? On Cisco 7940 I use "enable_vad: 0", but I can't find anything similar for 7905. -- Tomislav Parcina tparcina#lama.hr