similar to: one-way audio and isdn4linux

hi I have a passive isdn port configured in modem.conf in extention.conf i use this two channel (ttyI0 and ttyI1) with the string: exten => _NXXXXXXXXX,1,Dial,Modem/g1:${EXTEN}|60|r how can i hide my msn? is it possible to activate the clir with the @ before the ${EXTEN}? thanks Cristian

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm having some problems using the asterisk modem driver with an ISDN4Linux card (AVM Fritz). (I realise that it's better to use CAPI, but unfortunately this card doesn't have any CAPI drivers). Every so often the ISDN just stops working (it neither dials out nor accepts incoming calls). Trying to dial out just logs: --

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello! After LOTS of research on this list and internet in general I managed to get an old Teles PCI card working with Asterisk throught ISDN4Linux. No echos, no delays, simply perfect -- electronic poetry ! :) eheheheheh I just didn't get it to work with CAPI and "chan_capi" but, since isdn4linux is doing such a good job, I'll

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

Hello List! I finally got asterisk with capi working, and its already answering my call as well! :) Now i would like to call a number from my shoft phone (kphone). This is my extentions.conf: --- [general] static=yes writeprotect=no [globals] CONSOLE=Console/dsp ; Console interface for demo IAXINFO=guest ; IAXtel username/password

Hi everybody ! I've a Pentium IV with a USR ISDN PCI Card W699. Card I've installed asterisk 1.0.0 and it's working fine with outgoing call to POTS But it never answers to my incoming call from POTS and I don't understand why. I tested the modem also with the minicom utility and I never saw the "RING" status It seems that the modem didn't know somebody is

Hi all, I'm playing with Asterisk and I've already configured all needed .conf files. It works quite well, but now I need your help to tune the system: when I place a call from a softphone to the PSTN, I can't hear directly Telco's tones and I can't use its services, e.g. a mobile's answering machine. I don't know if I have to modify the dialplan or if it depends on my

Hello all, I currently have an Eicon Diva Client isdn card using i4l. Outbound dtmf doesn't work (and never has), but there has been an annoying problem with false dtmf detection in calls (that could be triggered easily by blowing into the receiver on the remote end). I looked through the list and found two patches that need to be applied - 1 to isdn_tty.c in the kernel, and another to

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

Can anyone work out why my callerid doesn't work on my isdn4Linux with asterisk (or without asterisk for that matter)... This used to work fine, and I am quite confident that the telco is sending callerid information (because they always do on all ISDN lines standard, only extra cost on POTS lines). This is the information from dmesg, whether asterisk is running or not: isdn_net: Incoming

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

I'm trying to use an hfc based pci card with asterisk but every call fails falling in the congestion extension. exten => _0.,1,Dial(${TRUNK}:${EXTEN:${TRUNKMSD}}||tr) exten => _0.,2,Congestion Looking in the syslog i can see: isdn: HiSax,ch0 cause: E001B it seems that this is a terrible error when arrives... hard to tell what is the cause. Also terrible is finding a lot of material

hi, i installed asterisk and works very well, the only problem is that when i try to call a direct number of a company that has a normal PBX i got this error: to 10.8.210.153:5060 == Accepting call on 'SIP/a.sampietro-f7be' (a.sampietro) -- Executing Goto("SIP/a.sampietro-f7be", "doisdn|BYEXTENSION|1") in new stack -- Goto (doisdn,00115601992,1) --

Hello All, I was just after a few pointers. I have just setup my Redhat 9 linux box with asterisk. Internal SIP call working fine. My Eicon ISDN card turned up today so - plugged it in and went through the modem.conf. It reports unable to open /dev/ttyI0 The problem is I have never used ISDN with Linux - let alone a telephony app - and I have no idea even where to start. Some pointers

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway

We have setup an asterisk box to let everybody call into the university internal network, but I get unexpected hangups when doing an outbound call from SIP to the ISDN interface, and it happens from 20 seconds to some minutes into the call. ----------the dial and the problem----------- -- Executing Dial("SIP/57966-a19d", "Modem/g1:96121||rt|") in new stack --