similar to: Struggling with ISDN4Linux and Asterisk config

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm having some problems using the asterisk modem driver with an ISDN4Linux card (AVM Fritz). (I realise that it's better to use CAPI, but unfortunately this card doesn't have any CAPI drivers). Every so often the ISDN just stops working (it neither dials out nor accepts incoming calls). Trying to dial out just logs: --

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

I have asterisk loaded and seemingly working with 4 snom 200 phones. I cannot dial in or out using a DIVA isdn card When I dial out i get "not found xxxxxxx" on the handset. When I dial in i see in /var/log/message isdn_net: Incoming call without OAD, assuming '0' isdn_net: call from 0 -> 0 1856 ignored isdn_tty: Incoming call without OAD, assuming '0' isdn_tty:

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hello all, I currently have an Eicon Diva Client isdn card using i4l. Outbound dtmf doesn't work (and never has), but there has been an annoying problem with false dtmf detection in calls (that could be triggered easily by blowing into the receiver on the remote end). I looked through the list and found two patches that need to be applied - 1 to isdn_tty.c in the kernel, and another to

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

I'm trying using Asterisk over an isdn line. I configured my Eicon Diva card by the hisax module and it works with the Asterisk's chan_modem (and chan_modem_i4l) driver. The problem is that I can receive calls (on /dev/ttyI0) but when I make a call I always have the line busy (on ttyI0 but even if I use an other device like ttyI1). This is a part of my consol output: --

Hello, I acquired a Diva Server 4BRI for an AsteriskPBX system and installed a 2.4.20 kernel modified with the latest eicon capi2.0 support from www.melware.net. Capi support seems to work fine: Asterisk+chan_capi answers the calls. However if I try to use my old isdnutils apps by loading a i4l compatibility layer then I have the following problems: - if I use the diva2i4l module and start the

G'day, New to Asterisk alert! I have a Netjet card running on linux 2.4.27 kernel using the HiSax module, and trying to use it for incoming/outgoing calls from *. I've tried playing with modem.conf and extensions.conf every which way I can think of, using samples and whatever I can find off the net, and I get the same message everytime I try to dial in. The complete message is:

Hi, I have a problem that I just can't figure out how to solve. I start *, dial it using a ISDN phone over PSTM, to a Hisax card installed in * I get the demo-greeting, listen for a few seconds and hang up. I dial it again, but this time the first second is sound from where the previous call ended, then the greeting starts as it should. Right now I have removed all codecs but codec_gsm.so

I need HELP pls! BRISTUFF: Bad Sound quality CAPI : PTP Mode dont supported mISDN : kernel is 2.4.x and not 2.6.x HISAX : PTMP ok, PTP incoming ok but in outgoing asterisk dont compose number(i listen dial tone and than i can compose number via dtmf) Asterisk CLI (g3 is group of Modem[i4l]/ttyI0 and ttyI1): Called g3: 3453444444

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Greetings, today I'm recompiling asterisk on a new machine with the same isdn card (not the same model, the *SAME* card) using CVS downloaded yesterday night. When I try to start *, it gives me the error: [chan_modem.so] => (Generic Voice Modem Driver) == Parsing '/etc/asterisk/modem.conf': Found == Loading modem driver chan_modem_i4l.so => (ISDN4Linux Emulated Modem

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello! After LOTS of research on this list and internet in general I managed to get an old Teles PCI card working with Asterisk throught ISDN4Linux. No echos, no delays, simply perfect -- electronic poetry ! :) eheheheheh I just didn't get it to work with CAPI and "chan_capi" but, since isdn4linux is doing such a good job, I'll

Hi There I am running SuSE Linux 9.3 and installed Asterisk from the RPM's. I have a Diva ISDN card, making use of the HiSAX drivers. Configuration seems to be OK. I can receive a call coming in on the ISDN and route it to a SIP (softphone) on my PC. As soon as I hangup the call, then asterisk stops working. I am forced to kill the process with -9, a normal kill does not work. The last

We have setup an asterisk box to let everybody call into the university internal network, but I get unexpected hangups when doing an outbound call from SIP to the ISDN interface, and it happens from 20 seconds to some minutes into the call. ----------the dial and the problem----------- -- Executing Dial("SIP/57966-a19d", "Modem/g1:96121||rt|") in new stack --