similar to: How to delay dialing

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

I have installed a 6VPCI card from voicetronix's but i can't get astersik to use it! Now looking at the loaded modules the chan_vpb is not loaded- so I assume that is why it is not working. Now I modified my vpb.conf file and extensions.conf, have I missed something Has anyone a installation guide as I am very new to this!! I have had asterisk working with SIP extensions. by dowloading

Hi, does anyone have any recommended (read tried and tested) way of making asterisk be able to handle incoming faxes. I've a PC running asterisk with a digium E1 card in and simply want to be able to route a call to some application which will take a fax call and save the fax as an image. I guess the bits I'm unsure of are how to terminate a fax call without a modem (if this is

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial

Hi there, Besides the problem of Voicetronix dialing too early before the carrier gives a dial tone, there also appears to be issues with the audio quality when more than 1 channel is utilized.

Good day all We have a voicetronix openline4 card If someone calls in from the outside the pstn and into the system and hangsup asterisk does not deteck the hangup any Idea why please Help Altus

Hi all, I used to have an OpenLine4 card, but decided against using it due to some problems with hangup detect. Does anyone on the list actively use Voicetronix's OpenSwitch12? What are your opinions on the card? Cheers, Flynn

Since updating * via CVS earlier this week, I've been having problems with cdr_mysql. Prior to that time my queries and cdr all worked fine. Now, even though my queries still work, I get the messages similar to this: ERROR[1211374384]: cdr_addon_mysql.c:203 mysql_log: Failed to insert into databas -- Hungup 'Zap/74-1' Anyone have any suggestions what went wrong?

Any guidance on how to get my openline4 to get recognized by asterisk@home? I've got my vpb drivers running, but not sure how to add it as a trunk, should it be via zap? or is there another way? Thanks, Chuck

Does the voicetronix card work with Asterisk? -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of woody+asterisk@solutionsfirst.com.au Sent: Monday, February 02, 2004 11:06 PM To: asterisk-users@lists.digium.com Subject: RE: [Asterisk-Users] Pictures of new multiport FXO/FXS from digum > -----Original Message-----

Good day all I'm getting this error while trying to dial out on my asterisk server using a openline4 card "exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872" Please Help me

Hi All, Just a quick question, but I could really use some help on this one. I've got the CVS-Head of * installed and running, and am using a VoiceTronix OpenSwitch12 to connect to 12 analouge lines. I've got callerid activated by the Telco, and can get callerid using a std phone. However, using *, I always get an error 'Cannot decode callerid'. Does anyone know if I need to

Hello, I have 5 digium's g.729 codecs and succesfully register with asterisk, I have incomming call from my cisco AS5300 to Asterisk through IP. But Asterisk always use g711 ulaw instead of g.729. When I disable all other codecs other than g.729 in both cisco and asterisk, calls get dropped once connected. The codec list show on my cisco AS5300 for g.729 are: g729r8 g729br8 I suspect that

Dear all, I have the following lines in my extentions.conf file; ;All US Calls exten => _9001XXXXXXXXXX,1,Dial(IAX2/dornoch:xxxx@10.xx.xx.xx/${EXTEN:1}@outbound) ;Dial 9 for outgoing numbers exten =>_9.,1,Dial(Zap/g1/${EXTEN:1}) ;include Brunswick switch => IAX2/dornoch:xxxx@xx.xx.xx.xx/sip What I'm trying to do is to send any calls starting with 9001 out through