similar to: # transfer with IAX2

G'day list, I am getting a lot[1] of traffic on my Internet link, ICMP messages from 69.73.19.178 telling me UDP port 5036 is unreachable (this IP address belongs to iaxtel.org). I see from the wiki that IAXtel supports only IAX2 from December 2003. Fine, however it looks like my * still wants to try and register using IAX1, and I can't find how to turn this off. This situation is

I'm still using asterisk v. 0.9 I think it is using IAX1 as the ixa.conf is set port=5036 Can I register with a provider who is using IAX2 ? When I set it up and run: iax2 show registry - it is not displaying any registered provider. -- #Joseph

Hi again, I'm attempting to figure out how to transfer calls from an IAX client. I have read and seen on the list where if you put a ,t at the end of the dial portion in the extensions.conf file that you should be able to use the # to park and transfer calls. I have not found this to be the case. I have tried it several different ways and I can't seem to get it to work. Can anyone

Hi, I am very closed to implement the IAX2 version in DIAX, but still some issues which I don't know how to handle, maybe someone from this list can help me. Trying to register with the * server as in version 1, I get the following in the * console: NOTICE[1150495040]: File chan_iax2.c, Line 2919 (register_verify): Inappropriate authentication received and in the client: Registration

Does Asterisk support Radius accounting?.... -----Mensaje original----- De: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] En nombre de asterisk-users-request@lists.digium.com Enviado el: Lunes, 17 de Noviembre de 2003 12:08 p.m. Para: asterisk-users@lists.digium.com Asunto: Asterisk-Users digest, Vol 1 #1912 - 11 msgs Send Asterisk-Users mailing list

Today has been the day for satellite questions, apparently, so I'll proxy one out to the rest of the community... I asked this tangentially a month or two ago, but I'll put it in a more blunt way: If you have IAX2 trunking mode experience over satellite, please let us know your experiences with that protocol/transport combination. I've got several people asking about IAX2 and

I was just noticing that my asterisk box is trying to register with my providers on both IAX1 and IAX2. They do register on IAX2, but it seems like it keeps trying to register with IAX1 also. Is there a way to disable this behavior, or am I just misunderstanding it. I just want to make sure I'm not wasting processor time and bandwidth trying to register IAX1 when it is already

Just in case anyone else is looking for this information, I'm posting the answer here. I do need to double check if this works with asterisk >= 0.9.0. I've heard rumors that IAX1 support has been removed in newer versions. ---------- Forwarded Message ---------- Subject: Re: [Asterisk-Users] Disable IAX1 Registrations Date: Thursday 17 June 2004 04:43 pm From: "Chris A.

Does anyone know of a way to transfer a call from the CLI? AJ

Can anyone give me presise instructions on how to compile cdr_mysql.so? When I initially installed asterisk on the system, I didn't have mysql installed. Since then I have installed mysql, created the database and table structure for cdr_mysql and placed the appropriate settings in the cdr_mysql.conf file. However when I do a show modules at the CLI I cannot find cdr_mysql.so.

Does anyone know what the Grandstream Budgetone is going for $$$ in the US? I didn't immediately see pricing on the phones page. AJ

Hi, all Please help me. My platform is RedHat Linux 9.0. I have a wildcard x100p. I just installed asterisk by following step: # cd ../zaptel # make clean ; make install # cd ../libpri # make clean ; make install # cd ../asterisk # make clean ; make install # make samples When I test Asterisk typing # asterisk –vvvvc I get one error and one warning: [chan_iax.so] => (Inter Asterisk

For anybody who didn't know there is an article on asterisk in February's Linux Journal. AJ

Hello All When I open up iaxcomm, it registers fine with the asterisk server. If I call into it, iaxcomm will ring; however if I leave iaxcomm sitting idle for awhile (I haven't figured out exactly how long) it seems to miss calls. I can see the calls coming in on the asterisk server but they never ring through on iaxcomm. If I close it and reopen it, it takes calls again fine. I thought I

Hi, Short version: Is it possible or even legal to convert an IAX2 PROGRESS/EARLY-MEDIA indication into a DAHDI/q.931 ALERTING signal when your ISDN provider does not pass early media on receipt of an PROGRESS(8) indication? Long version: I have an Asterisk 1.6.2.18-rc1 based system with a DAHDI trunk (UK E1 line), also, the system has IAX2 trunks, and several SIP handsets. All 3 protocols

Hi all, Thanks to Steven Sokol great work, the IAX2 bug in DIAX is now solved. For the interested people, you can download the new DLL (just the IAX2 version) from the following location: http://www.laser.com/dante/diax/wiax2.zip Replace the wiax2.dll file in the app directory with the new one and this is all. Please test it and send me your feedback. I intend to release a new DIAX version this

Hi, I have a wildcard x100p. I just installed asterisk by following step: # cd ../zaptel # make clean ; make install # cd ../libpri # make clean ; make install # cd ../asterisk # make clean ; make install # make samples When I test Asterisk typing # asterisk –vvvvc I find one error and one warning: [chan_iax.so] => (Inter Asterisk eXchange) == Manager registered action IAX1peers ==

In taking a cursory browse at Vonage's site today, I noticed they are now offering a soft phone. Has anyone had any experience using this? And does this possibly open new opportunities for using Vonage with Asterisk? Just thinking outloud on the list, soliciting thoughts and experiences from others. AJ

I would like to know how to define the s extension when I have an incoming PRI line? Currently I have 5 incoming DID numbers. Four of these DID numbers I have going to specific extensions, the fifth number which is the main number I wish to go to a background sound where callers can hear message, get directory, dial extension, whatever. I see that the way to normally do this would be to

Greetings all, As most of you probably know from my previous questions on the list, I'm still in the newbie category. My question today is pretty brief, as I told you all a few weeks ago I ordered a PRI from Verizon. I understand that there is a "B" channel that comes with this. The question is just what can I use this "B" channel for and how??? Thanks AJ