similar to: Sip phones transfer not working.

I just got 2 IpDialog phones for use with my Asterisk system. I have been able to get the phones to just dial local extensions but it is not able to register with my system correctly. I would like to know if someone has set these phones up before and how they did it! Is there any examples for use with Asterisk? They seem simple enough to config with there web interface. Thanks

Ok here is another problem I have run into. I have a Sipura 2000 and I have been able to configure line 1 with only one small problem. But I can't get the line 2 working with asterisk. Here are samples of my sip.conf and extensions.conf. If I disable line 1 I can then get line 2 working. Is there a sample configuration for the Sipura to get both ports working with Asterisk. Sip.conf

I am trying to get the following phones for testing. Is there a distributor in the US that is able to sell me these Sip phone and ATA adapters? I can not afford the Cisco phones there too hard to configure and too expensive! 1 - Sipura SPA-2000 2 - Grandstream Sip phone BT-102 1 - Grandstream HT-286 1 - Snom 105 Sip phone. I have called and emailed chagres but they have not reply. Nor

I would like to know if anyone has come up with a script for 911 dialing rules that put correct information on our locations. We have our office in 3 different building one being our production & shipping dock. It is almost 2 blocks away. We are connected with Ethernet Wireless between the buildings and have Sip phones setup in the other 2 locations. All the phones are working just fine.

I would like to prevent * from dialing 900 and 976 numbers. I setup the following settings in extensions.conf. But this does not seem to work! I don't know what I am doing wrong please help! exten => 1900XXXXXXX,1,Congestion exten => XXX976XXXX,1,Congestion exten => XXX976XXXX,1,Congestion exten => 1XXX976XXXX,1,Congestion exten => 91900XXXXXXX,1,Congestion exten =>

I have a problem that sometimes lines will go into what I call never never land. The Asterisk system will put a line with <Zombi> on it when you type show channels it will make the analog phone line dead. And on the CLI it says: astsvr*CLI>Zap/1-2<ZOMBIE>(macro-twoline-exten,s,1)Up Dial Zap/1-2|20|r I have tried to release it with soft hangup Zap/1 & also soft hangup

I have about 5 snom 200 phones working fine with everything. Voicemail, Transfers and all. Except I can't seem to use them to pickup parked calls nor place a call on park. I also have sipura-2000 with analog phones that are able to pickup parked calls and to park them. Most of them are on firmware 2.04g I have upgraded one to 2.05c for testing but this did not fix the problem. I get no error

Yes folks it's me a Newbie. Remember I am also a non-Linux person trying to learn. I have a production Server running Asterisk .5 12/02/03 CVS, and would like to upgrade it to the new .71. Has anyone come up with instructions (Documentation for us newbie) on how to do this? My server is running Mandrake 9.0 which I know nothing about! Sorry if this sounds stupid but all the instructions I

Hello I am still having problems with IAXTELL and FWD configuration. I get the following when I dial 17009965342 which is set as an example to dial to FWD people. 1+700+99+ 5 digit number. I have placed XXXXX where my passwords are. CLI> Executing Dial("Zap/14-1", "IAX/abatista:xxxxxx@iaxtel.com/917009965342@iaxtel") in new stack -- Calling using options

Ok here is a question that has gotten me stumped. I have an Asterisk system up and running. I need to connect it via the Internet to a Sip Cisco system. This is what they have. I have there IP address's and login. X-lite is able to connect to them and make a call! So I have the name right! CISCO router model: 2621 VoIP module: NM-HDA-4FXS I have done Google lookup and at the Wiki about

I need to get 2 Asterisk servers working together. I have been reading and doing just about every example I have been able to find here on the list and the Wiki. It's now gotten to the point that nothing on box2 seems to be working. I seem to have a major problem understanding the format. Here is what I have so far. It's 3 days of hair pulling and nothing seems to work! Asterisk box 1

Are you looking for local or Long distance? What will these T1s primarily be used for(inbound/outbound, domestic, local, long distance, international) How important are per minute rates to you? how many minutes do you expect to use per month? We are in Tampa Florida and have 15 T1s from several different providers so I may be able to refer you to one if it's a match to what you're

Hi all, DIAX 0.9.3 is available for download from the same place: http://www.laser.com/dante or http://www.geocities.com/tdanro The new DLL contain the latest updates made by Steve in the iaxclient library. Still just IAX1 is supported (for the moment). What's new in 0.9.3? - accept blank passwords; - accept for registration/calls host names, not only IP Address; - password no

I have 2 Snom 200 and would like to get them to work properly with Asterisk. With the Firmware 2.02t I am able to use the phone. But only one line configured. With there newer firmware 2.03o it will not allow me to make calls. But I can get calls on the unit. Again the 2nd line is not able to be registered. Is this an issue with Asterisk or Snom? I could use some example configuration

Hi, I have this scenario Cisco 5300 (public ip. 200.47.xx.xx) <---> Asterisk (public ip: 64.76.xx.xx) <--> Cisco 3600 (public ip: 64.76.xx.xx , same network than * ) When a calls comes in Cisco 5300, this send this calls with SIP to *, asterisk plays a welcome message and resend call to Cisco 3600 that have 4 analog lines connected... but after cisco play welcome message and when

I have a Mediatrix 1204 FXO gateway setup for SIP. I would like to know if anyone has gotten this item to work with Asterisk. I need to get a 2 or 4 port FX0 gateway working with asterisk. The Idea is the following. PBX at lets say any Hotel(Analog lines FXS) - FX0 Gateway(1204) -- {Internet} -- Asterisk - local IVR system. (IVR is not at present running Asterisk old dialogic system has FX0

Hi I am a user of Asterisk-0.5.0. I am a final year student of MCA in IGNOU.All the system are running in Red Hat-7.3 OS. I am able to transfered call in the following procedures: PSTN(INDIA)>>Mediatrix 1204>>Asterisk server>> VOCAL server>>Mediatrix 1204>>PSTN(USA) Now I want to save the cdr data in my Asterisk box.I am using RedHat-7.3 OS. I am using the

Hello, I recently tried an upgrade of CVS on my test server today and found that the res/res_parking.c file is completely gone. This is where I had to go into the code every time I do an upgrade and change the code to allow for doublehash transfers instead of single hash transfers: That means that you need to hit the pound key twice to initiate a transfer instead of once. Because of our inbound

Hello, I was using the doublehash.patch that Iain Stevenson had created back in August to change the transfer key from a single hash "#" to a double-hash "#". It always patches properly, but when I went from CVS 2004-01-12 to Asterisk 0.7.1 it doesn't seem to work anymore. I've attached the patch to this email and I use the following command to patch it: patch -p1

I have gotten the Cisco 7960 working with my Asterisk system under SIP. The version is 5.03 that I am using. Cisco Support said I should not upgrade to version 6 yet. My next question is the sound is patchy when people here me. But I can hear them just fine not patchy. I have the 188 page Admin manual and it seem not to say anything about improving the sound. All other phones like IPDialog work