similar to: Voicetronix OpenLine4: disable answering on a particular channel & delay before dial

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Hi there, I am trying to delay sending out DTMF from Voicetronix OpenLine4 to the CO line. The reason being is that Voicetronix sends out the DTMF too fast even before the line is fully established with the carrier. Usually when dialing an 8 digit number, only 7 digits are actually successfully heard by the carrier. Currently, my dial plan is: exten => _9.,1,Dial(vpb/1-1/${EXTEN:1}) Daniel

I am just starting to deploy asterisk in our office to use as our primary phone system - we plan to use a Voicetronix OpenLine4 card as our PSTN gateway - but one thing at a time... haven't got that far yet. Currently, i'm trying simple IP to IP calls within the office using our Cisco 7960's phones running SIP. When I make a call between these two phones, the conversation is of a

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Hi I would like your comments on the openline4 card from voicetronix. I am trying to get one working and find it difficult. I was able to get asterisk working yesterday but now it doesn't work anymore While it worked I was able to make some calls and I heard a lot of jitter Any comments appreciated. Patrick

Does the voicetronix card work with Asterisk? -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of woody+asterisk@solutionsfirst.com.au Sent: Monday, February 02, 2004 11:06 PM To: asterisk-users@lists.digium.com Subject: RE: [Asterisk-Users] Pictures of new multiport FXO/FXS from digum > -----Original Message-----

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hi all, I used to have an OpenLine4 card, but decided against using it due to some problems with hangup detect. Does anyone on the list actively use Voicetronix's OpenSwitch12? What are your opinions on the card? Cheers, Flynn

Is anyone using the VoiceTronic Openline4 PCI (fxo) card? I am trying to setup Asterisk using a Digium 40B (4 port fxs) and an OpenLine4 (4 port fxo), however I can't find any examples or post that utilize this card. I have my stations (Sayson 390) ringing each other, but haven't had any success ringing out. I have the OpenLine4 loaded and all of the new drivers working good, just

I'm looking to use Asterisk to replace my current PBX system. I'm in Australia so I need to use Austel approved equipment. My plan is roughly as follows: - Get a box with a suitable card and install Asterisk - Connect our existing PSTN lines to the Asterisk box - Get suitable softphones/ip phones to connect to the Asterisk system - Route all intra-office calls over our VPN - Route all

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12

Any one has documented how-tos for making voicetronix openline 4 to work with Asterisk. I have been contacting Australian Digium resellers and Digium cards are not approved in Australia. So I suppose Australian users are interested into putting Voicetronix in use. Any expereience to share will be most appreciated. David Kwok -------------- next part -------------- A non-text attachment was

One of the suggestions I got for dealing with my analog FXO woes was to look into using a Voicetronix card instead of the Digium. They're more expensive but if it worked better it may be reasonable. They indicated they were compatable with the CVS HEAD version of *. Can someone share with me their experiences with Voicetronix OpenLine and/or OpenSwitch cards with *? I'm specifically

Ron, VoiceTronix worked with me last week and backported the new chan_vpb that's in the current HEAD CVS tree to the 1.0 stable branch. So if you are using 0.7.2 or 0.9.0 you can go to the VoiceTronix website now (note that this is very new) and download an Asterisk package. When you download it there is an new chan_vpb.c that needs to be put in your asterisk source code tree. Also there

Hello, list, I am using Asterisk with an OpenLine4 card. It worked well with Asterisk 1.0. Then I upgraded the system, Asterisk 1.4 had some problem to compile chan_vpb, but I managed to compile it manually. Still Asterisk does not work because it refused to load chan_vpb module. I had to revert back to install Asterisk 1.2. Then I get a error: asterisk: hip.cpp:793:

Hello all, I hope this is not off-topic, if it is please let me know. I'm currently playing with an Asterisk at home, in order to get to know it's ins and outs. Very very impressive indeed. I've got it hooked up to my home phone line via a Wildcard clone board (Intel modem with Ambient chipset), and it works like a charm. Zaptel picks up the card as a generic clone, and works with it

Hi there, Besides the problem of Voicetronix dialing too early before the carrier gives a dial tone, there also appears to be issues with the audio quality when more than 1 channel is utilized.

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial