similar to: Voicetronix Openline 4 + asterisk

One of the suggestions I got for dealing with my analog FXO woes was to look into using a Voicetronix card instead of the Digium. They're more expensive but if it worked better it may be reasonable. They indicated they were compatable with the CVS HEAD version of *. Can someone share with me their experiences with Voicetronix OpenLine and/or OpenSwitch cards with *? I'm specifically

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Ron, VoiceTronix worked with me last week and backported the new chan_vpb that's in the current HEAD CVS tree to the 1.0 stable branch. So if you are using 0.7.2 or 0.9.0 you can go to the VoiceTronix website now (note that this is very new) and download an Asterisk package. When you download it there is an new chan_vpb.c that needs to be put in your asterisk source code tree. Also there

Hello, I can't have asterisk working without echo when I place a call from IP phone (SIP or H323) to a PSTN Phone. The called number as no problem with echo but there is a very audible echo in the SIP phone. This situation occurs either when connected with ISDN card thru i4linux driver and with my openline card from voicetronix. Do you have any suggestion fo that? Regards, Daniel ANDRE

Hello, I would like to know if voicetronix card (specially openswitch6 and 12) can be used with asterisk. Is there any driver for this card? Best regards, Daniel -- Daniel ANDRE (mailto:dandre@iris-tech.fr) IRIS Technologies - http://www.iris-tech.com Serveur kwartz - http://www.kwartz.com

I'm sorry if this has been answered before. I seem to remember reading a similar thread a while back, but for the life of me I can't find it (after 30 minutes of intensive googling). I have a voicetronix openline 4 card in an * server running CVS HEAD as of 1st March. Everything is working pretty much as as expected (with a little more echo than zaptel?). The question I have is

Hello all, I hope this is not off-topic, if it is please let me know. I'm currently playing with an Asterisk at home, in order to get to know it's ins and outs. Very very impressive indeed. I've got it hooked up to my home phone line via a Wildcard clone board (Intel modem with Ambient chipset), and it works like a charm. Zaptel picks up the card as a generic clone, and works with it

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12

I'm looking to use Asterisk to replace my current PBX system. I'm in Australia so I need to use Austel approved equipment. My plan is roughly as follows: - Get a box with a suitable card and install Asterisk - Connect our existing PSTN lines to the Asterisk box - Get suitable softphones/ip phones to connect to the Asterisk system - Route all intra-office calls over our VPN - Route all

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hi there, Besides the problem of Voicetronix dialing too early before the carrier gives a dial tone, there also appears to be issues with the audio quality when more than 1 channel is utilized.

Hi All, Just a quick question, but I could really use some help on this one. I've got the CVS-Head of * installed and running, and am using a VoiceTronix OpenSwitch12 to connect to 12 analouge lines. I've got callerid activated by the Telco, and can get callerid using a std phone. However, using *, I always get an error 'Cannot decode callerid'. Does anyone know if I need to

Hi, Recently I launched a new social networking site and am now looking to expand teh team in retrun for a % of the site ownership. If you are interested and having previous expereience working with rails projects / marketing please contact me via http://www.emokoo.com/public/contact_us Thanks -- Posted via http://www.ruby-forum.com/. --~--~---------~--~----~------------~-------~--~----~ You

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial

Hi all, I used to have an OpenLine4 card, but decided against using it due to some problems with hangup detect. Does anyone on the list actively use Voicetronix's OpenSwitch12? What are your opinions on the card? Cheers, Flynn

Hi, Firstly it appears you are not passing the extension to be dialed to the Dial command, so the driver is dialing badly. It should be something like dial(vpb/1-2/102) since this is a line port. Admittedly the driver needs to check better that the number it is trying to dial is legit but it doesn't :) P. --- You Wrote --- From: "Jacky" <jacky.taiwan@msa.hinet.net>