similar to: Issue - vmail.cgi on Redhat 9 (Apache) ?

I have just checked the Openbsd box on the if interface. fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 address: 00:02:55:30:54:28 media: Ethernet autoselect (100baseTX full-duplex) status: active inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255 inet6 fe80::202:55ff:fe30:5428%fxp0 prefixlen 64 scopeid 0x1 xl0:

Yes folks it's me a Newbie. Remember I am also a non-Linux person trying to learn. I have a production Server running Asterisk .5 12/02/03 CVS, and would like to upgrade it to the new .71. Has anyone come up with instructions (Documentation for us newbie) on how to do this? My server is running Mandrake 9.0 which I know nothing about! Sorry if this sounds stupid but all the instructions I

Referring to my previous post about degradation of voice quality when having more than 2 connection. The actual route is: pc xlite -> local asterisk box -> iaxtel -> local asterisk I have tried out a different situation: pc xlite -> local asterisk box -> iaxtel and the second connection pc xlite -> local asterisk box -> iaxtel -> local asterisk The same degradation

sorry for the cross post, but this is germane to the developpers as well as the larger user community. Re: [SIP 0000104]: [patch] Cisco-like NAT trick for outbound SIP connections On Sat, Jan 03, 2004 at 08:07:29PM -0600, bugs@digium.com wrote: > > A BUGNOTE has been added to this bug. tabarnac! it's been months now! the only thing that i can think at this point is that mark

> But this is not to say _you_ can't built a reliable VOIP based > system. Get _two_ providers and set up your dial plan in > extensions.conf to "fail over" if one service fails to > connect to dial via the next one and finally if both fail > use pstn. your users will see a system the "just works". Now there's an idea. I'm playing with this now,

hi all what about this... I just put together a box on a web shop (komplett.no) that will cost me NOK ~1850 (? 216) plus a small ?50 drive and cables, so say ?300. This consists of a cheap MB with a duron 1400, 256MB SDRAM and two HFC-PCI cards (if capijod will finish off the zaptel-driver soon). This is all in a cheap PC case. What do you think? Should this be doable? as a product? With only IP

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040331/c2abf19f/attachment.htm -------------- next part -------------- Hello, Is there any work in progress for supporting SMDI in Asterisk ? if Not, could anyone tell how to get started implementing it for Asterisk. Regards, Tony

Anybody knows what do I need to tell Asterisk to issue a re-INVITE between two SIP phone to avoid having the media going through the server? Tks, Al __________________________________ Do you Yahoo!? Yahoo! Hotjobs: Enter the "Signing Bonus" Sweepstakes http://hotjobs.sweepstakes.yahoo.com/signingbonus

Hello, I have Asterisk running on a RH9 box; Everything seems to be working as it should, except for Festival. Every time that Festival is called from Asterisk, Asterisk silently shuts down. Festival doesn't give any error indication and Asterisk just plain dies without a peep. Festival was installed per the Wiki, using source and patched with festival-1.4.3-diff; it works fine at the

thanks for the reply. the problem is after i start icecast with icecast -c /path to icecast.xml, i see the following: Changed groupid to 501. Changed userid to 501. and then it just hangs. i do not get a command prompt or anything. so i was wondering if there are any other messages that normally follow during the startup process. <p>--- Karl Heyes <karl@xiph.org> wrote: > On

Just spended ~ hour googling - all boards are based on GC-XX or I750X Chipsets - all for Xeons. There also some boards for Pentium 3. Can someone point me to a board with 64Bit 3.3v PCI for ordinary P4 with 800Mhz FSB. Thanks

Hello! Has anyone gotten 4.9R to recognize the "ServerWorks CSB6" ATA controller on a Dell 600SC? How about installing 5.2R on a 600SC? 5.2R recognizes the said controller, but it corrupts data. -- eof

Is anyone signed up with Vonage and using an asterisks box?? Also what VOIP providers would anyone recommend? -- James Moran Potential Technologies http://www.potentialtech.com

Hello Everyone, I'm using Mandrake 10 and trying to learng Samba 3.0.2a. I compile the source and install it alright on my Mandrake linux (./configure, make, and make install). Here what I'd done after the installation: Add to /etc/services file swat 901/tcp Add to /etc/inetd.conf file swat stream tcp nowait.400 root /usr/local/samba/sbin swat Since swat binary in the

Hi, Do the callers in USA dialling from USA Telco lines always have to prefix the CITY/AREA code with "1" in order To successfully make a call to other USA destinations? ---- I have not been to USA (yet) :) Ta SJ

I recently switched from Mandrake to Redhat and I noticed that vmail.cgi does not work with the default apache installation that comes with Redhat. Here is what I get in my error logs: [Thu Dec 04 11:59:57 2003] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Thu Dec 04 11:59:58 2003] [notice] Digest: generating secret for digest authentication ... [Thu Dec 04 11:59:58 2003]

Hello, We've released another update to our Asterisk GUI Client suite: http://astguiclient.sf.net/ Screen shots: http://astguiclient.sourceforge.net/screenshots.html The client suite runs on both Windows and UNIX and includes a dialer (the suite is not an asterisk configuration tool) In addition to the usual bug fixes, this is mostly an update for the VICIDIAL dialer application.

I am having trouble locating webvmail on my * server. Is this a seprate porgram or does it come with *. I am running version asterick*CLI> show version Asterisk CVS-03/26/04-17:08:20 built by root@localhost.localdomain on a i686 running Linux asterick*CLI> Thanks Kurt __________________________________ Do you Yahoo!? Yahoo! Photos: High-quality 4x6 digital prints for 25¢

Hello, What do you recommend for keeping track of user activities? For preserving bash histories I followed these recommendations: http://www.defcon1.org/secure-command.html They include using 'chflags sappnd .bash_history', enabling process accounting, and the like. My goal is to "watch the watchers," i.e. watch for abuse of power by SOC people with the ability to view