similar to: DTMF via SIP not working for certain phone systems

Hello all, When I generate an out-going call from *, the DTMF detection is not working ? ASTERISK --> GW AS5300 --> PSTN But the DTMF is working correctly when it's an incoming call. PSTN - -> GW AS5300 - -> ASTERISK Well, I tried with the 3 dtmfmode of asterisk inband, rfc2833 and info, no way !!! Is it normal that asterisk try to setup the outgoing-call using ULAW ? if I

Do somebody using CISCO AS5350 with Asterisk? Which protocol do you using: H323, MGCP, SIP? This direction: [12sp->Asterisk->h323->as5350->isdnPSTN] is ok But reverse: [isdnPSTN->as5350->h323->Asterisk->12sp] cannot hear 12sp, but 12sp hear PSTN (codec g711u) -------------- next part -------------- An HTML attachment was scrubbed... URL:

Has anyone succesfully integrated * with a cisco voice gateway ? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031214/3b1ba7b3/attachment.htm

Here is my Configuration PSTN -> Cisco AS5350 -> SIP -> ASTERISK -> SIP -> ATA186 When I call from the pstn to the ATA, the ATA rings but I don't hear anything on the calling side until the call is picked up. When I call from the ATA, everything seems to work fine. When I bypassed ASTERISK, everything seems to work fine. Anyone know what I might have configured wrong?

I'm stuck running a old copy of asterisk because something strange is going on in later versions of the CVS.. When I call in from a PSTN into my cisco 2610XM gateway which then routes the call to my asterisk box via sip.. Asterisk can no longer process DTMF tones generated by the calling party. This affects DISA, prompts and menus.. Has anyone else had this problem?? and use.. I DO have

Hello, Has anyone experienced a segmentation fault in asterisk for using G729 against an AS5300 in SIP ? I'm having this problem. Also, any other codec I use gives me incompatible media (can be read in SIP DEBUG messages). AS5300 configured for multiple codecs, so is Asterisk. Tried G711u/A G723 and G.729. Any clues ? Regards, Jorge A. Info: Asterisk ver 1.0.7 stable Using AMPortal

Try sending 5350 config and oh323.conf, versions, etc... -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Goran Dj. Sent: Wednesday, December 22, 2004 4:43 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Asterisk->AS5350 misplaced RTP to 127.0.0.1(AS5350 party

I am seeing strange behavior that I don't understand. Voicemail2 and voicemailmain2 work fine if I call from a sip phone directly connected to *, but if I call either of them from an analog line on the other side of a sip gateway, voicemail seems to ignore digits. If I am recording a message and press #, nothing happens except that it records the tone onto the message and I can't specify

I have 2 questions regarding asterisk logs that I really hope someone can help me with. Jan 7 09:40:14 WARNING[1009517568]: File chan_iax.c, Line 3537 (registry_rerequest): Received unsolicited registry authenticate request from '209.242.15.34' I get this IAX message every minute or so. I have 2 asterisk servers that both register with each other. I can post the configuration again,

Hello, One of the Sipura 2k's I'm using has a dialtone that occasionally fades to static when the user picks up the line. Are there any settings that I can check that would affect this? Regards, Christopher

More top posting goodness... Please post your updated dialplan. After making the change, did you reload/restart Asterisk so the changes would take effect? --Tim ----- "Mohit Saxena" <MohitS at starcomms.com> wrote: > Still no luck.... > > Br, > Mohit > > -----Original Message----- > From: asterisk-users-bounces at lists.digium.com >

My configuration is: [ISDNPRI] -- [CISCO AccessServer AS5350] --<H.323>-- [ASTERISK] -- [CISCO ip phone 12SP+/Skinny] When call is initiated from IP phone -> Asterisk -> AS5350 -> ISDN everything working ok (RTP is ok). But, when call coming from ISDN -> AS5350 -> Asterisk -> IP phone IP phone party can hear ISDN party, but ISDN (incoming) party canNOT hear IP phone party

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

Are there any known issues with call-waiting caller-id for SIP? Caller-ID on the first call works fine, but when the second call comes in, I hear the interrupt tone, but the caller-id doesn't display anything. I have tried this with the Cisco ATA and the SPA-2000. I have also tried two different phones to verify that it wasn't something specific to the phone. Thanks, Stephen

Hi, I am currently interconnecting to a PRI using a Cisco AS5350. I'd like to be able to dial specific numbers out by a specific isdn channel, so for e.g. if I dial 999 01 12341234 it should send 12341234 out via isdn channel one from the Cisco AS5350. If somebody would be able to guide on this, it would be appreciated. Regards, Sahil Gupta VoiceValley

Can someone please explain what I am doing wrong here? I only want the extensions listed in long-users to be able to access the longdistance context. If I do this, I get a congestion tone no matter what I dial. If I add a [default] context and include => longdistance, then the local callers can call the long distance number fine, which is not what I want, but I still want long-users to be

We're having an issue with connecting a Cisco ITS installation to * such that DTMF tones are passed to *. DTMF tones aren't passed to voicemail or to any of the interfaces behind *. On the Cisco Side: dial-peer voice 8 voip destination-pattern 9999$ session protocol sipv2 session target ipv4:172.16.1.249 session transport udp dtmf-relay rtp-nte codec g711ulaw no vad We have also

Is there a cisco vpn client for linux centso 5 AMD 64 bit? Using google it talks about cisco vpn client but everyplace to download is blocked. I then found a vpnc reference but did not find a 64 bit version. yum install vpnc did nothing.... What is my next step? Jerry

Hi, I'm trying to get a remote Cisco Call Manager Express (CME) system behind a dynamic IP address routing both inbound and outbound calls via SIP to my local asterisk server. I've got a local CME system working fine on the LAN, where the CME is at a static IP (host=10.5.7.130 in sip.conf), but I can't figure out how to get it working with host=dynamic, even locally on a test

I have an * box connected to a Nortel SL100 through a PRI (US) using the Digium TE410P (quad-span T1 card). I don't have access to the SL100 - it is handled by another group. The span comes up OK (timing, framing fine). However, as soon as the D channel comes up, I get endless "HDLC Bad FCS" errors. I modified logger.conf to get rid of the messages (so I could see what else was