similar to: How to load the driver of TDM400P card!

Hi all i need urgent help our entire switchboard is down only 5 days after it came up. this is the second time this has happened and i am thinking that asterisk is not worth the trouble it gives. mostly it runs without hassle. but around 2 weeks ago during the test phase we rebooted the machine and did the normal modprobes and this error popped up. coming back to work after the weekend the

Hi, I got my TDM11B and am trying to get it to work on my PC. However, I'm having difficulty getting the wcfxs driver to load. I've Googled this problem, and while there are others who have ran into the same problem, none of the solutions work for me. I would very much appreciate it if you could suggest things I could try to resolve this problem. Details follow. The PC is somewhat

Hello, my first post to the list. I have started to install and play with Asterisk. I was following some basic instructions to 'jump-start' my system. I have a TDM400P with one port and a X100P. I am running the latest CVS versions (from today). Following the steps I found for basic jump-start I did the following: Modprobe zaptel Modprobe wcfxo Modprobe wcfxs Edited

Hi All I've bought a TDM400P and need some help with configuration. Can you tell me what to do ? I've tried to install and the message below has appeared: [root@voip asterisk]# modprobe zaptel [root@voip asterisk]# modprobe wcfxo /lib/modules/2.4.22-1.2115.nptl/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid

All, I have FC3 fedora core 3 and just installed and compiled 2.6.10. after rebooting I attempted to recompile zaptel-1.0.3. I did a make clean then make. I got the following errors. Any suggestions? ------------------------------- /usr/src/digium/zaptel-1.0.3/torisa.c:1139: warning: 'set_tor_base' defined but not used CC [M] /usr/src/digium/zaptel-1.0.3/wcusb.o CC [M]

Hello I am (attempting) to run the astlinux version of Asterisk on a VIA embedded platform. I have a TDM04B and pretty sure zaptel.conf and zapata.conf setup OK. They worked fine with same card in traditional PC anyway. I think need the module wcfxs for a Digium TDM04B card. Is this module not part of astlinux? Do I need to download it? Or is it in opt? I see wctdm - but think that is

I need to reopen this discussion because it's impossible to run spandsp (and VoIP) under these circumstances. With zaptel unloaded, I see the following "vmstat 1" output: no swapping, an occasional disk output, +/- 1003 interrupts/sec., less than 10 context switches/sec., CPU idle 100%. A very quiet system. I load modules zaptel and wcfxo, and the system utilization stays the

Need some help with modules.conf, and basic RH9 linux skills. I've installed the new TDM04B 4-port FXO card and its working. After a reboot, when I do lsmod I see the wcfxo module but not the wcfxs even though both are listed modules.conf. If I "modprobe wcfxs", then lsmod has both modules showing. The wcfxs module is the last one in the modules.conf. Is the order of entries

Of course I am not a kernel expert, so .. please be patient. I am investigating on my zaptel/zapata problem. As the main error message asterisk quits on mentions <'/dev/zap/channel': No such file or directory> I went peeking over there. [Asterisk Verbose Error Mar 13 20:43:35 WARNING[5779]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or

I found similar posts regarding this error but none that answered my question. My zaptel.conf reads: fxsks=1-2 fxoks=3 loadzone=us defaultzone=us and /proc/interrupts: CPU0 0: 5542402 IO-APIC-edge timer 1: 2 IO-APIC-edge keyboard 2: 0 XT-PIC cascade 8: 3 IO-APIC-edge rtc 14: 72582 IO-APIC-edge

Hello all, I've posted on this problem before. Well here goes again. I have an intel mobo with a p4 2.4ghz proc, 1GB Ram. It has built-in ethernet and vga and 6 pci slots. I dreamed of making this my household communications server: internet router, firewall, vpn and asterisk. Everything works except the TDM fxs card. Well it works for a little while and it dies: no dialtone, no

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G

I'm debugging a TxFax problem whereby the fax transmission fails. I suspect interrupt latency--some interrupt routine is holding its interrupt too long. I have all unnecessary services switched off and X is not running when I perform these tests. Some transmission are successful while others fail at random points. I've noticed that after I boot Linux, load zaptel, wcfxo, and wcfxs,

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hi all, I've struggled for several days trying to get a Digium TDM04B 4-port wxfco card working on a Dell 1U PowerEdge 750 machine running Fedora Core 1. I finally got a call back from Digium who indicated that there is a fundamental conflict between the card and the PowerEdge having to do with PCI interrupts. Asterisk version is stable v1-0 12/29/04. The symptoms of the problem were as

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031223/62cf404e/attachment.htm -------------- next part -------------- Hello When I tried loading TDM400P module using insmod command, I get following error messages. Is there some problem with my asterisk installation. Please advise. Thanks Tony $insmod wcfxs Using

Hi, I recently purchased two X100Ps and a TMD40B. I have set everything up according to the instructions however I can't get asterisk to pick up an incoming call (It just keeps ringing). Also, when I pick up an internal extension I get dead air. I searched the mailing list for 3+ hours -- What am I missing? Thanks in advance for your help. Here are the installion steps that I used:

Sorry, but this may be a really dumb question. How do I load the zaptel modules wcfxo and wcfxs at boot time on my Debian Sarge system? The file zaptel.init used by the command "make config" appears to be designed for redhat type systems and does not work for me. I have tried reading the man pages for update-modules but I'm stupid and cannot figure it out. Thanks, Mike

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

/bin/sh: -c: line 0: syntax error near unexpected token `;' /bin/sh: -c: line 0: `if [ -n "" ]; then if [ -f ]; then mv -f .bak ; fi; cat .bak | grep -v "alias char-major-250" | grep -v "post-install torisa /sbin/ztcfg" | grep -v "post-install wcfxsusb /sbin/ztcfg" | grep -v "alias wctdm" | grep -v "post-install wctdm