similar to: Grandstream budgetTone registration time out

Anyone have any example scripts in PHP that connect to the manager? I'm not really a much of a programmer so I could use boost. Once I can figure out how to get it to login properly, I'll be ok from there. Thanks, Kevin _____________________________________________________________ Are you a Techie? Get Your Free Tech Email Address Now! Visit http://www.TechEmail.com

Hi. There is not much info on the FWD site about this. What codecs do they use? When I try to connect with X-Lite, it works with GSM. When I try to call out with *, it wants G729. I have disallow=all and allow=gsm in the sip.conf. I end up getting errors: Unable to find a path from G729A to GSM Unable to find a path from GSM to G729A What's up with that? I was able to make a call once

[Posted here becasue your mail server is rejecting my direct reply to you.] Hi Martin, AFAIK SIP can run on both UDP and TCP but I have only seen it used over UDP.. :) To setup the GS phones you need to open up the following ports (If its still set at the defaults)... UDP/5060 UDP/5004 UDP/5005 UDP/5006 UDP/5007 I have not tested the GS phone through a firewall yet but this config should

hi, can someone who has used Budgettone phones tell me how to do the following: an incoming call comes in and is answered by the receptionist. she need to put the call on hold, speak to whoever the call is for, and either (after that) pass on the call, otherwise speak again to whoever was on the call and hang up .. so far i've got as far as a blind transfer by pressing transfer button and

Hi. I just tried updating asterisk and I guess I broke something. Here's the log: Unable to find a path from G729A to SLINR Unable to find a path from ULAW to G729A Any ideas on what I should try? I tried nuking all the zaptel stuff in the system and the source and started over agian. Also nuked the asterisk config files.... I saw this asked once before but there was no reply :-/

hi there .. I asked sometime ago regarding getting a Budgettone working with Asterisk over G729. My system is quite simple, Asterisk server with 1 G 729 license installed, and 10 Grandstream phones. Only one of them needs G729, because it's on a remote link via an ADSL bridge. The rest run happily on G711 on a local network. I added the lines disallow=all allow=g729 to the sip.conf entry

Checking the earlier mails, it stated that the phones were $75 (100) & $85 (102) ref :- http://lists.digium.com/pipermail/asterisk-users/2003-June/013483.html Well, I just called Ovislink/dgtimes and was quoted $90 & $100 and the person said there was no price change. Anyone on this list actually bought them at the $75 & $85 rate ??? Regards...Martin -- Too much is just enough.

Just got my new Budgettone phone, and I've got a couple of issues. Most important, it doesn't seem to be querying for the time via NTP. I put a sniffer on the line, and once it boots up the only outbound traffic it generates is an attempt to contact a TFTP server, which is programmed in as 192.168.0.168. . . Must it first find a config file (it's asking for "cfg.txt")

--- Jonathan Tew <jonathan@ultracart.com> wrote: We've got the app_queue configured to supposedly allow for a call to be transferred. When the call comes in and an agent answers it (using X-Lite Pro) and then decides to transfer the call (using the SIP phone interface) they get disconnected from their call and after left logged in to the queue system. Obviously we're doing

Sorry, this is a re-post. I sent the message from the wrong e-mail address. I was checking up on the cvs changes. Hi. I just tried setting up the send url function of Queue app, but it did not seem to work with gnophone. I must have missed something. It never tries to go to the page. I have this in extensions.conf: exten => 1,3,Queue(support,t,http://www.yahoo.com) It shows in the

Hi there! I installed the BudgetTone (GrandStream) on my LAN without any problems. Then, I moved it to another location using a D-Link NAT. I opened 5060 (SIP) and 5000 to 5008 for RTP. I also fixed the IP address of the BudgetTone. When I receive a call on my Asterisk, it would ring my FXS as before. However, after I pick up, it hangs within a few seconds (Hungup Zap1-1 in the log). The

I've searched the lists but I didn't find anything exactly like this. I have two Grandstream BT101 phones connected to an Asterisk. Periodically, for reasons that I can't determine, one or the other (or both) of the BT101s decide(s) to go on permanent busy. Dialing that phone gives: -- Executing Macro("SIP/24567-7856", "dialphone|SIP/27654") in new stack

Hi- I am attempting to setup my Budgettone phone for use with my * server and am having problems obtaining an IP address. I have checked the phones settings to make sure it has dhcp enabled and it is. The display says no IP. I bought the phone but do not have any documentation other than the Wiki, but I am still at a loss. What could be preventing the phone from picking up an IP address? Any

hi .. i've just converted myself back to a newbie by trying to experiment with some new stuff .. I have connected two grandstream Budgettone 100 phones to my asterisk, and trying to experiment with them .. I am trying to get into the asterisk sample basically .. when I dial 1000 asterisk receives the call, but I do not hear any sound on the phone. Dialling from phone to phone direct (via

Hi. I just started trying to play with Sphinx. I followed their site as far as running sphinx-server. It is listening on the default port. I copied sphinx2-simple to another file and changed sphinx2-continuous to sphinx2-server. So, I ran eagi-sphinx-test under asterisk. What exactly is it supposted to do? Here's what I get: debian:~# sphinx2-simple2 sphinx2-simple: Demo CMU Sphinx2

Hi, I installed Asterisk an all works fine exept for Grandstream. When I call with a softphone (ex X-ten) to a Grandstream (BudgetTone-100), I can make a conversation. = ok When I call to a softphone with a Grandstream I can pich up the call with the softphone but the Grandstream keeps ringing like on the other site you didn't pick up the phone.(even if you do so) It's the same when I

Since the last firmware upgrade we've been experiencing some odd CallerID behaviour. Instead of the LCD showing the calling party's #, the phones are showing the internal extension being dialed. This is probably a really stupid fix I'm overlooking, but I was hoping someone could offer some insight. Thanks! -Corey -- Corey S. McFadden McFadden Associates - Technology

Hi all, I'm quite new on this mailing list, and I discover the asterisk world. I m experimenting a PBX with SIP phones, grandstream budgetone (not expensive for tests) All the features I need work just not one : the supervised call transfers. I know there are a lot of posts about that, but none gave me the correct answer (unless I missed it). Here is my config : 2 sip phones BT102 with

I have my new phone mostly working. I do have a couple of residuals that I cannot find mentioned in the list archives: 1. Is it possible to set the volume in these things? I hope I didn't miss it, but I've looked in the doc, the FAQ, and the asterisk archives and don't find anything. The displays in the pictures all have more bars on them than my phone does, and I need a bit

hi, I have the following configuration: Grandstream --> NAT (Netgear RP614)-->Internet-->Asterisk(public IP) i can register fine and call ringing is working as good. The problem is = i cant hear audio both ways and i get this error: WARNING[22544]: File rtp.c, Line 375 (ast_rtp_read): RTP Read error: Resource temporarily unavailable my sip.conf file is as follows: