similar to: FWD and (multiple) internal IPs

Asterisk stopped answering the calls. I'm just experimenting with asterisk, upon setup there is a [demo] context. I have SPA-3000 with PSTN line: Dial plan 2: S0<:1000@10.0.0.101> my sip.conf localnet = 10.0.0.101 localmask = 255.255.255.0 [3000] type=friend host=dynamic username=3000 secret=my_secret mailbox=3000 context=from_pstn callerid="PSTN GW" <3000>

I had been running an older patched CVS to get VOIP working with NAT and everything had been running fine. I just built * on a new box with CVS-01/18/04-12:19:25. And now I can get remote SIP users to register. Has anything major changed... [general] port = 5060 ; Port to bind to bindaddr = 0.0.0.0 ; Address to bind to externip = 69.132.68.17 ; Address

Lance, Have you configured your sip.conf to use these aprameters under General? ;externip=66.213.227.66 ;localnet=192.168.1.0 ;localmask=255.255.255.0 -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Lance Grover Sent: Thursday, June 02, 2005 9:39 AM To: Asterisk Users Mailing List - Non-Commercial

Hi, just to repeat my previous post (and trying to find a solution): Setup is * behind NAT. I can use FWD (time service, echo server) without problems when I add this to sip.conf: externip=a.b.c.d ; a.b.c.d is the IP of the router (Linux/Nat) outside_addr=a.b.c.d My ICH however now responds with: -- Got SIP response 481 "Call Leg/Transaction Does Not Exist" back from

I found this configuration file on Wiki for FWD behind firewall ; SIP Configuration for Asterisk ; [general] disallow=all allow=ulaw port=5060 ; Port to bind to bindaddr=0.0.0.0 ; Address to bind SIP channel to externip=xxx.xxx.xxx.xxx localnet=172.16.1.0 localmask=255.255.255.0 context=inbound-sip ; Default context for incoming calls maxexpirey=180 defaultexpirey=160 tos=reliability

Hi :) I've had all this working before, but I'm revisiting it, and in short, I currently have huge problems receiving incoming calls. I've been trying with both FWD and voiptalk.org. I'm running CVS HEAD of asterisk, zaptel and libpri as of yesterday afternoon. Would someone mind helping? :) My machine is 10.0.0.1 on my LAN, but the ADSL router has 10.0.0.1 set as the 'DMZ

Hi guies, I know I know this subject have been The most written subject about VoIP Right... but I just want to make clear, just one time ! If Asterisk is on a Public IP Address and a softphone behind the nat, sip.conf must contains for this phone: nat=yes .... Now if I want to configure my sipphone (X-Lite) placing behing the NAT, it must have in "Domain/Realm" the external IP

This has probably been answered somewhere, but I'm stumped. I have two Zap channels (FXS and FXO), both working fine. I can call from Zap/1 to Zap/2 and reverse. I've also configured SIP channels, both inside and outside of my firewall. Inside can call outside, and outside can call inside. Also, both inside and outside can make and receive calls to/from Zap/1 & Zap/2. What

Hi all I use sipgate and FWD but seem not to get it going. I do not have NAT on the asterisk box (static ip). The asterisk box has 2 network interfaces. One internal and one external. Now when I make an call to a FWD or SipGate number all I get is -- Executing NoOp("SIP/113-6d2e", "") in new stack -- Executing Goto("SIP/113-6d2e",

I have an asterisk server behind NAT - no audio on the test external calls I have tried making so far. Read http://www.voip-info.org/wiki-Asterisk+SIP+NAT+solutions - No solution evident from there, sounds like I have case 9. I would have thought that all I would have to do is port foward and have the external IP on the asterisk server, which I have done I have fowared 5060UDP, 8000UDP, and

Hello there Yesterday I updated my pwlib, openh323 and Asterisk from CVS. After making "clean opt" in pwlib and openh323 and make "clean install" in Asterisk i get an "Undefined symbol" error when I try to start Asterisk. As far as I can see its when loading the h323 channel driver the error occurs. Do I have to update other things as well, by reading the various

Dear List members, After succesfully installing the * on a couple of systems, and putting them on test, I observed that there is an intermittent call drop on PSTN line. The systems are - Dell Optiplex P3/500MHz/128MB - Built-in ethernet - 1 X100P (Motorolla chip) card on PCI - 10G HDD etc. - Asterisk April 17 CVS. - 2 Mediatrix FXS ATA (4 phones) - 2 Grandstream phones. - sip.conf, zaptel.comnf

Egad, not again with Broadvoice! Anyhow, I recently installed AAH and configured my TDM11B and got that and some SIP phones working. I still have some issues to work out, etc, but my current problem is Broadvoice. I have checked out all of the online resources, including the recent list exchange about the recent changes made by Broadvoice. However, the one thing I have found to be consitent in

Hi All, I have a asterisk box that is now on its own static address on the net.it was originally behind a nat firewall. The problem I have is that the remote SPA-2000's that are behind nat firewalls now fail. here is relevent sip.con entry [2001] type=friend username=2001 host=dynamic defaultip=81.178.77.67 allow=ulaw dtmfmode=rfc2833 mailbox=2001@local context=sip

right, so far, here is what I've done: I succeed in take in a new variable the UUS1 field sent with the connection request for incoming calls. It was quite simple afterall... (I just had to find where the data CMSG->Useruserdata is coming in chan_capi.c) Now I would like to know where this field is instanciated for outgoing calls in order to control this step? I am looking for that but I

Hi Nitesh, check out my config that I have for the Faktortel config in the asterisk@home sourceforge forum, you'll probably be able to work out how to set it up from there. Cheers, Dean -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Nitesh Divecha Sent: Wednesday, February 23, 2005 4:12 PM To:

I have a PolyCom Soundpoint 500 sip phone. I'm tring to get the phone registered on an asterisk box but am having no luck. I get the following errors 192.168.22.196 being the phone and 22.254 being the asterisk box.. Apr 23 11:41:33 NOTICE[1133742896]: chan_sip.c:5623 handle_request: Registration from '"110" <sip:192.168.22.196@192.168.22.254>' failed for

Hello I have an asterisk 16.2.1 on an ubuntu on AWS, which is experiencing a drop in call. It does not have a certain time, it is random. The audio is flowing normally and the call is dropped. Has anyone ever experienced this? My settings changed below: allowoverlap = no udpbindaddr = 0.0.0.0 tcpenable = no tcpbindaddr = 0.0.0.0 transport = udp, ws, wss srvlookup = yes directmedia = no

Hi, I have the following problem. I have 5 phones behind the same nat (canreinvite=yes). it works fine to receive calls and to make calls. sound quality is good, so everything works fine. The poblem is that the phone behind nat cant call each other. It works if canreinvite=no. But i want to do this. Does anyone have an idea? Regards, cjk.

Now that I have most everything actually working I've noticed that about every 3-4 days on average..... and at worse... Once a day my asterisk box seems to lose it's registered state with our sip provider and no longer will take any incoming calls. The caller simply hears a fast busy (reorder) If I do a reload at the command prompt all is well for another few days..... What I'm