similar to: Sipura SPA-2000 is shipping, discount for asterisk-users

Anyone have one of these yet? http://www.voxilla.com/shop/index.php?action=item&id=38 -Dan

Hello all, So i am new to asterisk and very green when it comes to Linux, so don't beat on me too bad :) I just set up * on Red Hat 9.0 last night... everything "seems" to be configured coffectly, I can start * no problem and get the CLI prompt... now here is my question... I have an account set up with VoicePulse Connect! and also have a Sipura Spa-2000... i am trying to get make

Froogle found me one supplier for the SPA-841, not sure I trust them though. Does this phone even exist yet? Does anyone have any experience with it? Does anyone know a vendor other than Atacomm/voipsupply?

Voxilla news story: http://voxilla.com/voxstory84-nested-order0-threshold0.html Two new products * A Sipura 2000 in a linksys box: Linksys PAP2 Phone Adapter * A combination NAT router with 2 FXS ports: Linksys RT31P2 Broadband Router Jim James H. Thompson jht@lava.net

Problem: SPA3000 phone does not ring for incoming PSTN call although I can dial out. I set up my Sipura with the Voxilla Wizard which is pretty good but leaves out some important details. The Voxilla Wizard for Supura SPA3000 gave me a setting for PSTN Tab -> Dial Plans -> Dial Plan 8 (<S0:66610>) Should I put extension [66610] in sip.conf with a context in extensions.conf that

The folks over at CodeWeavers have given us two new dealcodes. :) A dealcode is coupon code that can be used in their online store. The two new dealcodes are "EmulateMe" this dealcode is good for a 15% discount on CrossOver or CrossOver Games for Mac and Linux. The second dealcode is "CxForLess" and it will get you a 10% discount on any product in their store. They also have

We have extra equipment that was over-ordered or unused. All of the equipment is brand new. The equipment has been highly discounted to move quickly - the last set of equipment sold in 48 hours. If this equipment is of interest to you, call or e-mail quickly. Buy on VOXILLA and SAVE $300 each (Cisco routers & switches): http://store.voxilla.com/customer/home.php?cat=259 For Sale (all new):

I have been trying to read everything I can find on Sipura 2000 and Asterisk. I am trying to make the Sipura-2000 act as two analog lines off my asterisk. I have followed (what I believe) the example on http://www.voxilla.com/Article39.phtml and I still can't get my Sipura to register with my Asterisk server. I can re-config my Sipura to talk to fwd, or voice-pulse connect and it works

Hi All, I'm on of those brave souls who bought into the preproduction beta of the Sipura SPA-3000 FXS/FXO adapter. I've had the unit a few days and am exploring it's workings. I really want it mostly as a straightforward FXO adapter, to replace an X101p. Let me be clear, I'd love to support Digium in every way possibe, and will likely buy a TDM40 card shortly. But, the X101p has

Hi, the topic says it all really. Does the Sipura 3000 detect and report UK clid correctly? thanks Mike

Hi all, I was wondering whether anybody here would help me clarify this minor issue please. If I have the following setup; Asterisk ------ Sipura SPA 3000 (fxo) --------- Pstn Line Would a call coming in on the pstn line be answered by the ATA or just get passed through to the * server (depending on dialplan) to handle? So basically, the caller does

Hi all, I need a fully developed web based remote provisioning system. I cant find anything reliable on the internet. Have already checked ataconfig.com and voxilla-ays.com. have tried to contact them but got no response. So if anybody knows a good provisioning system then plz tell me about it. -- Best Regards Rizwan Hisham Software Engineer Axvoice Inc. www.axvoice.com -------------- next part

Hello, I am very new to asterisk and voip in general and so far have managed to get the FXO card and a few sip phones working fine. My question is where does the Sipura SPA 2000 come in the picture? Can it be used as an extension (i.e FXS) ? Or is it to be used as a line (i.e FXO)? Or it can be used as both? My understanding is that its just like another ATA186. Is that true? I guess what I

I just got a refurb Sipura SPA-2000 and was able to assign it an IP address with DHCP and ping the device, but then I ran the firmware upgrade utility to bring it up to spa2k-2.0.13g which seemed to work just fine, but after it rebooted I cannot connect to its webserver for configuration. I can still ping the unit. When I use the built in voice menu it reads back the right IP address, webserver

Hi All, I am using a Sipura SPA-3000 as an FXO gateway to bring calls in and out of Asterisk. I am using "PSTN Ring Thru Line 1" (on the "PSTN Line" tab) so Asterisk answers the call rather than the SPA-3000. It is all working perfectly except I can't get the SPA-3000 to pass caller ID to Asterisk. It passes "Display Name", "User ID" and any "PSTN

How to Connect SPA-3000 to Asterisk so * will answer? After setting up Asterisk on Gentoo the extension.conf contains [demo] context; but my asterisk is not answering? In SPA-3000 in PSTN Line - tab under Dial Plan 1 I have: S0<:demo@10.0.0.101> Default dial plan is set to 1. My box's IP where Asterisk is running has IP: 10.0.0.101 Line 1 - tab has: SIP Settings Port: 5060 Nat is

Hello, I'm looking for a SIP to XMPP Jingle voice gateway. I see that Asterisk has Jabber and Jingle support, but it looks like Asterisk acts as a Jabber client. Are there any Jabber server solutions, where Jabber users can call SIP users by using the SIP URI and vice versa? -- Eric Chamberlain, CISSP Chief Technical Officer Voxilla - http://voxilla.com/

Does anybody out there have any evidence that Sipura support is still in operation? rgds benjk -- Sunrise Telephone Systems, 9F Shibuya Daikyo Bldg., 1-13-5 Shibuya, Tokyo, Japan. NB: Spam filters in place. Messages unrelated to the * mailing lists may get trashed.

Voxilla.com has a great config wizard for the SPA-3000 and * http://voxilla.com/spa3kasterisk.php I took the output from this wizard and dumped it on my test box with an SPA 3000 (with some mods to match my * contexts) and everything worked great. Calls from the PSTN to the spa3000 are routed to dialplan #8 on the spa3000, which dials * Both the FXO and FXS port register with * The SPA3000 is

Asterisk-users, Our two-part tutorial explaining how to use VoIP and Asterisk in Amazon?s Elastic Compute Cloud (EC2) has garnered quite a bit of attention. But due to the time required to complete the many steps needed to get up and running, some of you have asked if it is possible to create a much simpler to install ?pre-built? Asterisk EC2 ?instance.? In short, yes it is. And we?ve