similar to: maximum retries exceeded

Rowland, I decided to start over with a fresh install and attempted again. Only change I made was to start my mappings at 10000. I gave 'Domain Users' group gid 10000 and 'tuser' has uid 10001. Still didn't work btw. dn: CN=Test User,CN=Users,DC=domain,DC=local objectClass: top objectClass: person objectClass: organizationalPerson objectClass: user cn: Test User sn:

Hi Rowland, I forgot to tell you the results were from my Domain Controller and not the member server. Member server returned something to the effect of 'user not found'. I am only starting the 3 services(smbd,nmbd and windbindd) listed in the wiki. Should I be starting Samba with command line switches to start as a member server? Is that even possible? Thanks for you

Hi Rowland, If you don't mind I like to post my member server configuration as I attempt again. This is how my member server(Ubuntu 12.04) is configured after fresh install and prior to Samba build. Anything I'm missing that could cause my issue as I proceed? I assume no other prerequisites must be done on the other DC's either? Thanks. /*# From Wiki for DC build*/ apt-get

Rowland, I've gotten a bit further. It appears my use of '.local' is causing the issue from what I've researched. I ran '|/etc/init.d/avahi-daemon stop'. |This allowed me to successfully join the domain. Enter administrator at DOMAIN.LOCAL's password: Using short domain name -- DOMAIN Joined 'PFMEMBER1' to dns domain 'domain.local' DNS Update

Rowland, I had a typo in my hosts file which is the reason my initial DNS update failed. Corrected and joined again. Successfully joined and updated DNS A record. I then made sure to give 'Domain users' a id of 10000. I am now able to run' getent passwd' and see all my domain users! YES! However I still see something that confuses me. When I run 'id tuser' I get

Rowland, I did forget to change it. Is it as simple as renaming now or did I screw up? On 1/2/2015 12:18 PM, Rowland Penny wrote: > On 02/01/15 17:07, James wrote: >> Rowland, >> >> I had a typo in my hosts file which is the reason my initial DNS >> update failed. Corrected and joined again. Successfully joined and >> updated DNS A record. I then made

Rowland, That did it! Thank you so much. I do have a question regarding the 'getent' command before setting up file shares. When I run 'getent group Domain\ Users' I get domain_users:x:10000:user1,user2,user3,user4,user5,user6,user7,user8 Why does it show these specific users? I would assume it would only show my 'tuser'. I don't have uid's set for anyone

Hi Rowland, passwd: compat winbind group: compat winbind 'getent passwd tuser' results in a blank terminal line. On 12/31/2014 1:12 PM, Rowland Penny wrote: > On 31/12/14 17:55, James wrote: >> Hi Rowland, >> >> I did. Unfortunately something is still amiss. I do receive a >> response from 'getent group domain

Has anyone else had problems registering with Sipphone over the last few weeks? Previously, this had worked fine. I contacted Sipphone technical support, but they're not much help. register => 17471234567:password@northamerica.sipphone.com/123

Rowland, Thanks for the clarification. It appears the member server is joined and I have created a share. [demoshare] path = /srv/samba/test read only = no I have enabled ACL support and given 'SeDiskOperatorPrivilege' per the wiki. I can navigate to the share using Windows Explorer. If I set the share permissions to only me(Full Control). I can't access the share.

Rowland, That was the issue. Windows computer management console showed 0 connections. That obviously wasn't correct. A reboot corrected the issue. ACL's working as expected. I probably should have ran a 'netstat' to verify. Any best practices on who should or shouldn't have uid's or gid's set in AD? I've read where the Administrator account should

Rowland, Thanks so far for the assistance. I have a question about setting up shares on a member server. How do I map to users or groups that do not display in AD(Everyone,System,Authenticated Users)? On 1/2/2015 2:08 PM, Rowland Penny wrote: > On 02/01/15 18:59, James wrote: >> Rowland, >> >> That was the issue. Windows computer management console showed 0

Hi Rowland, Yes. When I create a share I get the expected 'Everyone' group under 'Share Permissions' for example. I'm assuming I must map this object to Unix so all windows users can access this share. However in AD there is no 'Everyone' group to set a gid. I wouldn't necessarily expect one either. I'm currently under the mind set that with a member

That is actually the wiki page I am currently referencing in my question. From the wiki you can see the 'Everyone' group. I would normally remove and add domain users or authenticated users. That prompted me to ask myself "what if I wanted the everyone group to have access"? How does the member server know who the everyone group is since the share is created on the server.

On 31/12/14 19:07, James wrote: > Rowland, > > I decided to start over with a fresh install and attempted again. > Only change I made was to start my mappings at 10000. I gave 'Domain > Users' group gid 10000 and 'tuser' has uid 10001. Still didn't work btw. > > dn: CN=Test User,CN=Users,DC=domain,DC=local > objectClass: top > objectClass:

On 01/01/15 00:07, James wrote: > Hi Rowland, > > I forgot to tell you the results were from my Domain Controller > and not the member server. Member server returned something to the > effect of 'user not found'. I am only starting the 3 > services(smbd,nmbd and windbindd) listed in the wiki. Should I be > starting Samba with command line switches to start as a

On 02/01/15 13:41, James wrote: > Hi Rowland, > > If you don't mind I like to post my member server configuration as > I attempt again. This is how my member server(Ubuntu 12.04) is > configured after fresh install and prior to Samba build. Anything I'm > missing that could cause my issue as I proceed? I assume no other > prerequisites must be done on the other

On 02/01/15 16:57, James wrote: > Rowland, > > I've gotten a bit further. It appears my use of '.local' is > causing the issue from what I've researched. I ran > '|/etc/init.d/avahi-daemon stop'. |This allowed me to successfully > join the domain. > > Enter administrator at DOMAIN.LOCAL's password: > Using short domain name -- DOMAIN

Hello I am trying to integrate OS X 10.10.4 clients into existing Samba infractructure run by our IT department. We are currently using Samba 4.2.3. File share is stored on iSCSI array with ext4 filesystem which should support both ACL and XATTR. We are trying to setup vfs_fruit module to avoid possible performance problems on OS X clients. We do NOT user netatalk. Current vfs_fruit config:

I have a situation here where a user has an AAstra 480i phone, which function corectly. The phone is behing a nat-router (a linksys wrv200 for it's VPN point to point facility). The phone is plugued in a port wich has qos enabled. And when the user places a call, sometimes (not always), we get this in the console : [May 8 13:41:55] WARNING[5804]: chan_sip.c:1948 retrans_pkt: Maximum