similar to: wpa_supplicant

I rebuilt my notebook that has the atheros card in it, and forgot to save all of my setup to get it working. I am using dkms and the madwifi rpms from rpmforge. My modprobe.conf has a line: alias wifi0 ath_pci I can ifconfig wifi0 up But the command: /usr/sbin/wpa_supplicant wpa_supplicant -dd -D madwifi -i wifi0 -c /etc/wpa_supplicant/wpa_supplicant.conf fails. Now some of my old

I remember being a small part of and following this thread a few months ago. <http://lists.centos.org/pipermail/centos/2006-May/065091.html> I've been attempting a go at getting wpa_supplicant running on CentOS 4.3 and haven't had much luck. I'm assuming my failure is my lack of knowledge on the subject, but anyways. First, my normal setup is as follows: IBM Thinkpad R40

I have not installed the madwifi specific kernel stuff (kdml and hal-kdml) from atrpms. I have installed with wpa rpms. And my Atheros card is working with almost no work on my part (other than runing wpa_supplicant as a deamon). Nice!

Has anyone else had any problems with getting wifi to work after upgrade ? I am using ipw2200 on an HP laptop - was working under 4.3 Ian -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20060906/3a518796/attachment-0002.html>

This is a new Centos 5.1 install on a HP nc2400 (that use to run XP). Completely clean install; blew away the XP partitions... After applying all the updates, and configuring for the rpmforge repo, I used yumex to install dkms and the dkms-ipw3945, ipw3945-firmware, and ipw3945d rpms. lsmod|grep ipw shows: ipw3945 180391 1 ieeee80211 33417 1 ipw3945 and dmesg)grep

I seem to be able to lock my machine by going into wpa_cli and asking it to 'reassoc'. The reason for question mark after "hard" is that debug information (caused by wlandebug and athdebug) is being printed on the console. The only way to get machine's attention is to hold power button for 8 seconds. Note: manual reassociation is just the handy way to reproduce the problem

I am installing CentOS5 on a dell Lattitude D610. dmesg: recognizes the the wireless Intel 2915: ipw2200: Detected Intel Pro/Wireless 2915ABG Network Connection I have googled for ipw2915 and centos5 OR rhel5, can't find instructions for installing the firmware. Should the firmware be installed from the CDs? Any suggestion? -- Thanks http://www.911networks.com When the network has to

I am using a Netgear MA401 with the wi driver, and am having trouble using wpa_supplicant to set static WEP keys. I have the wlan_wep.ko module loaded with wlan and wi built into the kernel. My wpa_supplicant.conf looks like this: ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=wheel network={ ssid="INTERNERD" scan_ssid=1 priority=1 key_mgmt=NONE

Hi Folks, I'd like to install my USB-WLAN-Stick Netgear WG111v3. Ndiswrapper works correct after installing Kernel-Modules from atrpm ndiswrapper-kmdl-2.6.18-53.1.19.el5.centos.plus-1.52-16.el5.i686.rpm. But by calling wpa_supplicant with wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d machine freezes. My wpa_supplicant.conf:

I want to buy a laptop and install CentOS 4 on it and have the wifi work when I'm done. (Hoping for reasonable specs: 2GHz, 40GB drive, 1/2 to 1 GB RAM, CD-ROM, light and thin, 13 or 14 inch screen....) Any recommendations?

I went to the wiki and searched for both wireless and wifi and did not find anything related to wireless cards in CentOS. I think it would be stellar to have something similar to the laptops page but for wifi chipsets. I would propose it have three categories: FOSS chipsets Native driver but not FOSS chipsets (ie atheros via madwifi) NDIS Wrapper FSF has compiled somewhat of a list at

On my CentOS 6: chkconfig --list wpa_supplicant shows off at all levels, which is confirmed by examination of: /etc/init.d/wpa_supplicant but ps -ef shows the process running. Furthermore, repeated cd /etc/init.d/ ./wpa_supplicant stop appears to succeed, but the process continues to run. These observations were made at levels 3 and 5. Thanks in advance for your explanation. Mike.

Hi all! I tried to use CentOS5 on an IBM Thinkpad R52 which has an Intel PRO/Wireless 2915ABG Mini-PCI Adapter installed. I downloaded the firmware from the DAG-Repo (afaik 3.0.0) and added a "alias eth1 ipw2200" to modules.conf. After the module was loaded successfully (including the firmware) I was able to configure the card. For simplicity I didn't use any encryption. My

Johnny Hughes <johnny at centos.org> wrote: > CentOS Errata and Security Advisory 2017:2907 Important > > Upstream details at : https://access.redhat.com/errata/RHSA-2017:2907 Will there also be an update for CentOS 6? Or does the problem not exist with CentOS 6? -- Yves Bellefeuille <yan at storm.ca>

Hi Sam, do you know if there is anything done about cbb(4)? I have many wireless adapters with ath(4), but only the one based on PCMCIA is making problems on FreeBSD. I cannot boot my notebook with the device inserted into the port, or it will render the system unusable (100% load on cbb(4)). And all I can see is the following: Jul 12 14:58:39 link kernel: ath0: ath_chan_set: unable to reset

hi all, this is my first hit on the mailing list. hope i m posting in the right place. well, i have a dell vostro 1510 laptop with broadcom wifi adapter. n it doesnt work! :( i installed the wifi drivers with ndiswrapper. iwconfig shows the following. [root at laptop ~]# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wlan0

first, the short form of the question -- has anyone got that wireless adapter working on centos 5.5 and associated with an access point that uses WPA/WPA2 security? and the details. in a classroom where there is *no* wired networking at all, all PCs have only that wireless net adapter, which works fine on windows but, after installing centos 5.5, unsurprisingly, we have no networking. there

Hi, I've got a task to have a small number of laptops netboot Linux over WiFi. The kernel is loaded off the USB stick of cource, it's off topic for now. The WPA-supplicant daemon is started early by dracut off initrd. It works. Mostly. The problem is that upon shutdown systemd terminates all the processes FIRST and unmounts filesystems NEXT. Guess what? Upon termination,

Hi, I cannot have suspend and hibernate working on a Samsung NC10 (netbook) running CentOS 5.4 i386. When I try suspending/hibernating the screen becomes black (with a few logs, like "shrinking memory" for hibernate) and then the computer hangs and I have to force a shutdown with the power button. This wiki page seems to say that it should work out of the box:

Hi, I have CentOS4.1 up to date and I get on boot: ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection divert: allocating divert_blk for eth1 ipw2200: ipw-2.2-boot.fw load failed: Reason -2 ipw2200: Unable to load firmware: 0xFFFFFFFE divert: freeing divert_blk for eth1 ipw2200: failed to register network device ipw2200: probe of 0000:03:03.0 failed with error -5 My understanding