similar to: RE: Grandstream BT-100 and latest CVS

>I was successfully using the BT-100 phone with CVS 11/10. Now that I've >upgraded to 11/27, I can't place an outbound call. However the phone is >registered and works well with inbound calls. Any suggestions will be >appreciated. Thank you. Hi! I encounter similar problems. But in my case also incomming calls are not possible. But this might be because of my upgrade to

I hate to bother the list with this potentially minor issue but.... I just wonder if it's a symtom of some other problem. Every time I make a call the BT-102, with the latest firmware, she just keeps the LED display lit and the timer counting after hangup. I check the CLI and the hangup is being executed, I certainly was concerned it might be keeping the line open but that doesn't seem

dear all, can anyone assist on how to enable callerID to appear on grandstream bt-100 sip phone. [1003] type=friend context=default username=1003 secret=**** ;fromuser=1003 ;callerid=John Doe <1234> host=dynamic nat=no canreinvite=yes dtmfmode=rfc2833 incominglimit=1 ;mailbox=1234@default ; mailbox 1234 in voicemail context "default" disallow=all allow=ulaw allow=alaw

Good day all We have one Bt-100 that logs on to the server,works for a few min and then just starts loosing registration Jan 13 13:10:05 NOTICE[-1101505616]: chan_sip.c:7503 handle_request: Registration from '<sip:144@192.168.0.250>' failed for '192.168.0.145' Jan 13 13:10:05 NOTICE[-1101505616]: chan_sip.c:7503 handle_request: Registration from

Has anyone got a working zaptel.conf and zapata.conf for a Digium Wildcard TE110P T1/E1 Card. It's connected to a BT ISDN PRI (EuroISDN) with 24 channels. Inbound works fine, but outbound isn't setting CLI (it seems the line supports 6 digit CLI). Inbound CLI works fine. In the dial-plan using Set(CALLERID(num)=123456) then Dial(Zap/g1/01234567||frT) Where 123456 is in the range of BT

Is anyone using this combination successfully? I have a dell 500sc running rh9 and asterisk 1.0rc1. It is configured with an x100p. I have a Sipura SPA-2000, laptop with Xlite and a Grandstream Budgetone BT-101. I have signed up with Voipjet (they use iax2). I also have an FWD number via iax2. I can sucessfully call back and forth to all devices via zap, sip, and fwd. I can successfully

Greetings, 2 nights ago I upgraded one of my remote servers to the latest CVS Stable, Asterisk CVS-v1-0-02/07/05-16:13:48, and my inbound and outbound caller ID stopped working. At first I thought it was my carrier, so I've been yelling at them for the past day or so. I then upgraded my core network (about 8 asterisk servers) to the latest stable as of 3am last night, Asterisk

Ah... Looks like I have the 500's...Sorry. Ty Purcell -----Original Message----- From: Derek Listmail Acct [mailto:listmail@oversimplified.com] Sent: Thursday, September 09, 2004 12:21 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] Polycon IP 300 SIP vs Grandstream BT-101Deployment > I plugged it in, configured it, and it works great. I

I just noticed something when I 'sip show peers' from the CLI, I get the following: 6113/6113 x.x.x.x D N 255.255.255.255 62927 OK (66 ms) 6112/6112 x.x.x.x D N 255.255.255.255 50079 OK (160 ms) 6111/6111 x.x.x.x D N 255.255.255.255 60810 OK (141 ms) 6109/6109 x.x.x.x D N 255.255.255.255 51331 OK (151 ms) All of those

hi, I known, that this is not * related, but a lot of members of this ML uses GS BT phones. I have patched the atftp serber to recognize the TFTP OPTION, whis these phone send during boot. Patch includes - another locations for configs, firmware and ring tones - different FW versions for phones - custom ring tones for the phones You can find patch, source/unpatched/ and DEB for

Hi- I'm at my wit's end trying to get a Grandstream BT-101 POS to register on my * server. Asterisk version is 1.2.1. GS Firmware is rev 1.0.6.7. Basically, I've setup the phone following the instructions at voip-info.org, and it registers for about 10 seconds, then after receiving the SIP NOTIFY from the * server, goes into "flashing display" mode, which indicates some

Hi all, I'm having a really frustrating time with a bunch of BT-101 phones. They've been trouble-free and working very well for the past several months. A couple of days ago, some of the phones (but not all of them, yet) have started acting very strangely. All phones are running firmware 1.0.6.7, and are identically configured (except for the user/authenticate/password things) on both the

Hi, When we use BudgeTone-100 in our Intranet together with our Asterisk IP PBX everything is working OK. When we try to use the phone behind the Firewall we can't do the connection. When I try to use STUN Server: 128.107.250.38 there is no result. The only way in which I have audio from the one direction (BT-100 to Asterisk) is when I leave blank STUN Server and specify the IP Address in

I'm trying to fix a problem with the GrandStream Budgetone 102. I've been reading the source code, mailing lists and other resources. Here's the scenario and the approach I have been pursuing. I'm having some problems with the AGI calls and I hope someone can give me some clarification. PSTN <---> T1,PRI * <---> Grandstream BT 102 (12)

I'm considering a situation where I buy about twenty ATA devices. I've played with the Linksys / Cisco PAP2T, and got that working fine with some inbound and outbound faxing. The web GUI was okay. I'm seeing prices around $45 to $50 for this thing. It comes with two FXS ports, but I only need one FXS. I've seen the Grandstream Handytone 286 online. It looks promising as an

Hi, I have just completed the deployment of a couple of Grandstream phones (for internal IP use) and was wondering how much harder it would be to deploy a Polycom IP 300 phone. The Grandstream was quite easy to deploy and gives us good voice quality over DSL, however from some of the previous posts I am see that some people had troubles with the Polycom 300. The variant I am looking at

I'm seeing both inbound and outgoing call failures on our ISDN-30 lines that only seem to go away when I do a "zap restart" or in extremis restart Asterisk (1.4.25 with a Digium TE205P and zaptel 1.4.12.1). If I don't restart zapata or Asterisk the problem rapidly get worse :-( The lines are from BT with LCR from Cable&Wireless (I've tried using the LCR bypass code and

Hello- I have a system with one D410P and one B200P (both OpenVox). All is well with the D410P, inbound and outbound, and I can initiate calls on the B200P BRI span, but there may be something wrong with my inbound BRI setup: there is no indication of an inbound call when I dial in to it from the PSTN. When I run "pri intense debug" and make a call to the BRI span, I can see a

Hi guys Forgive the newbie question but I am setting up my first * system :-) I live in the UK with two standard BT phone lines. The hardware used is a TDM400P with two FXO and two FXS daughter boards. Currently only one FXO and one FXS line is used during testing. Incoming calls work fine, as do the phones plugged into the system. However outbound calls do not work. The number is dialled,

As a follow up to my previous post, I have now identified what is causing the bug with the grandstream phones. When the line faxdetection=incoming is in the zapata.conf file, the grandstream phones will not ring, nor connect a call to the zaptel interface. Can anyone else confirm this bug? I'm going to play with the different options (incoming/outgoing/both) to see if it makes a