similar to: g729 license

I am thinking about using the G729 codecs on my endpoint devices and purchasing some G729 licenses for Asterisk but I have several questions: 1. Which G729 codec is sold by Digium for Asterisk, G729, G729A, B...I? 2. If I have G729A on one end and G729B on the other, are they compatible? I have looked all over the place for question 2, but without buying the ITU docs I cannot seem to find this

Hello, I'm trying to find out if Asterisk will support plain G729 or G729b. I've read all over that it supports G729, but I can't seem to find any explicit remarks regarding the specific versions of the codec Asterisk will support. I noticed that Digium allows Asterisk users to register and download G729a, but refers to it as G729 on it's pages. I also noticed that on

Hey all! I had an experience trying to set up an E1 in Brazil which could help somebody. In Brazil is very common telcos to have just R2 digital as their primary signaling. As I were trying to set up an E100P, which does not support R2 yet, I had to test an other signaling which works perfectly with Asterisk. They call this signaling as RDSI, using ccs as framing and PA (primary access) as

I am having some problems with g729 with SIP and ZAP channels. 1) I have two g729 licences. Very frequetnly (I don?t know what triggers the error) I get the following warnings and error when I try to place a call via SIP to my X100P. The only way to get out of this is through a restart of *. When the error ocurrs there are no other calls in place. Any ideas? Error Opening channel:2 not

I have a fresh 1.4.10.1 installation that appears to have a problem with g729 pass-through. I can see the gateway in question sending an INVITE using g729b. However, the Asterisk is only sending g711 in the INVITE to my Polycom phone. [gateway] disallow=all allow=g729 [phone] disallow=all allow=ulaw allow=alaw allow=g729 There's the codec configs for the gateway and the phone in question.

Hello! I am wondering how the differences between G729, G729a, and G729b effect call bridging and server interoperability. For example, can one server use the G729 code with another server that uses the G729A codec? Also, which version is Asterisk set up to use? Thanks! Elliot

Hi everybody,, I need to block incoming collect calls to my Asterisk box but I could not find out where to do that. Went to zaptel.h but I did not see any timing which can be applied to collect calls. Does anybody knows if I can set this up in Asterisk? I'm using an E100P connected to the PSTN and a T100P connected to a Zhone 100. Version: Asterisk CVS-05/30/04-16:28:04 thank you Oz

I own a G729b codec from voiceage which I had from Digium a couple of months ago , I friend of mine had the new Digium G729 codec which registers in the asterisk as a Annex A/B codec, the problem that we saw is that the call goes thru find but we cannot here any sound. Asterisk is showing this : -- SIP/10.10.1.1-babc is ringing -- SIP/10.10.1.1-babc answered

Hi all, i have purchased the g.729 codec from digium. The registration was successful. (with the "old" binary) But there're a few questions: - should not the codec listed in the codec list when i enter "show codecs" ? - the codec is named with g729b but if i enter show codecs there is a codec g729a listed also the g729b is not installed. what is the difference between

Hi, Do the g729 codec licenses for Asterisk work on a SIP environment (only SIP UAs running g729 + Asterisk)? I would like to buy a couple for a SIP test lab but I have not found any documentation on wether it works for SIP UAs or not. The Digium page only mentions: "The G.729 codec works with all Digium cards." Can somebody tell me please? Thanks, Ricardo Villa

I want use iLBC and have following in mind, please help me is it possible ? ISDN <-----(ALAW)-----> * <-----(ALAW)-----> SNOM SIP??<-----(iLBC)----->?*?<-----(ALAW)----->?SNOM 1. ISDN incoming codec is ALAW SNOM codec should be ALAW (can't be iLBC because a lack of codec). 2. SIP incoming codec should be iLBC (snom is ALAW). 3. SIP outgoing codec should be iLBC /snom

Hey all, Does anyone know what this means? I was running asterisk fine. Installed it on a new pc and I am using the g729b. codec that is optional. I ran the install for the codec it went ok but when I run askterisk via asterisk -vvvgc it gives me this error anyone know? I make sure I entered in the correct reg number. I followed the steps correctly. Too Registration error! Please try

Hello, How many licenses to buy?? : From what we understood from digium website, we must buy as many licenses as the number of maximum simultaneous calls using G729 Codec we wish to make. For example, If we want to be able to make a maximum of 10 simultaneous calls using G729 Codec, we must buy 10 licenses. Is it right? Thanks you

hey, I bought a license for 729 but I can't use it this is the message. == Registered translator 'g729tolinb' from format 8 to 6, cost 99999 == Registered translator 'lintog729b' from format 6 to 8, cost 18 == Parsing '/etc/asterisk/enum.conf': Found Asterisk Ready. *CLI> WARNING[5126]: File chan_sip.c, Line 1601 (process_sdp): No compatible codecs!

I hope this isn't considered cross posting, i sent the following email to Digium support but figured someone on the list may also have better insight into my questions. I have purchased 2 g729 licenses from Digium for testing and have the following questions; ** My configuration is a single asterisk box configured with 2 g729 licenses and 2 x Cisco 7960 Phones, I have confirmed the

List, I purchased 2 g729 licenses but I can't get it to answer a g729 call from a cisco router with a vwic card. In the debug output below you will see that asterisk thinks it only supports: (gsm|ulaw|alaw|h263) when it should support g729 according to the config also listed below. The real odd thing is I can place g729 calls to the router, just not from the router to *. Anyone have any

hello all, i have problem in using g729 codec. my asterisk version is 1.8.22. when i run "core show codecs" in asterisk, there is a g729 codec in the list so i assume that i can use it for my channels. but connection can not be set when i use it for my h323 channel. i read somewhere that codec g729 is a commercial codec and i should buy its license in order to use it. is it true? if

I need a refresher course on how many licenses I need to buy. I have an Asterisk server that receives calls by SIP (G729) and then sends them to the PSTN via 32 Zap interfaces on an Astribank. I cannot remember if the license is per channel or per call so I do not know if I need 32 or 64 licenses for this application. Could anyone please remind me? -- Telecomunicaciones Abiertas de M?xico

Hello Everybody, Since I upgraded to 1.4 I always get the difficulties as below, which I have never had in 1.2: [Dec 28 21:05:59] VERBOSE[1734] logger.c: -- Call accepted by 202.153.128.34 (format g729) [Dec 28 21:05:59] VERBOSE[1734] logger.c: -- Format for call is g729 [Dec 28 21:06:00] VERBOSE[1756] logger.c: -- IAX2/VoIPRakyat-2 is ringing [Dec 28 21:06:00] DEBUG[1756]

Hi, Does anybody have ATA 188 working with any kind of fax machine? I've tried many different configuration following the Cisco Online Manual and I couldn't get this working with Asterisk. I were trying do change the ATA Connect Mode and Audio Mode reading the (http://www.cisco.com/en/US/products/hw/gatecont/ps514/ products_configuration_example09186a00800d698e.shtml) and allowing