similar to: RE: Aculab SS7/ISUP (new subject)

> > >On Thu, 2003-11-13 at 16:50, Freddi Hansen wrote: > > >>>> >Freddi Hansen wrote: >>> >>> >>>>> >> with boards from Aculab, we are replacing Aculab boards with Digium >>>>> >> boards BUT we would need more >>>>> >> Digium boards IF we could use both Digium and Aculab cards in

I hate to bring this thread back to life, but... > it may be possible to get it supported, do you think the price >point is remotely competitive with Digium hardware? Also as I am not >about to divulge my information to them to look in the downloads >section, what is the licensing of their SDK? What is the licensing of >the driver? > >Steven >On Tue, 2002-11-26 at 14:52,

Hi, one month ago, I announced, that I will look at the openss7 project in order to use it together with asterisk. It took a while for me to check the capabilities of and around the project. Since the openss7 project consists of only one person, and when there was just silence for a long time in the project's mailing list, I doubted, whether it was a good idea to consider using openss7. In

Hey All, I'm just daydreaming here.. but what's the status of SIP-T in Asterisk? I haven't been able to find a whole lot of info on SIP-T but seems like just an extension of SIP. Right? Now if I had a PSTN Gateway (that is a SS7 gateway) that supported SIP-T, could I signal * with SIP-T from it and have asterisk utilize MGCP to sieze a particular DS0 on a remote DS1? Hmm.. What am

Hello Trevor, I wonder how I can find out for sure what is the H/W version for a PROSODY ACULAB SS7 Card? I dought that I have a ver 1.1 which have may issues with recently made computers. I have a case opened for my problem with aculab but sysdiag shows that I have ver 1.1 and aculab says I have ver1.5! can sysdiag be inaccurate? I tried config summary and I had the same result! wish you

Hello, Is SS7 and PRI in any way compatible in that if the interface is configured one it will work for the other (granted, it will not have any of the ISUP, etc. parameters available if the line is PRI) or are they two distince protocols that have incompatible signalling? Thanks, Elliot

Hi, Would just like to inquire if anyone here has a setup of asterisk to send traffic to AS5400 connected to an SS7-PRI.? this is more of a AS54 question, as i've been reading and i always stumble upon PGW2200 as a requirement to handle SS7 signaling on the AS54. Has anyone able to send calls from asterisk to an as 54 with SS7-PRI without PGW2200? TIA Regards, Nhadie --------------

Hi, Does anybody have experience working with Aculab groomer II, to convert between ISDN E1 and non-ISDN T1, or anything similar. I am looking for sample config files. We have asterisk as ISDN E1, but for testing we set it up as regular T1 if we get sample config files. Zeeshan A Zakaria -- www.ilovetovoip.com -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All, I want packets [request/response] capture for ISUP packets , i have E1 line terminated to my digium card i just want a packets flow between my machine and teleco side, is any tool or utility [command] availabele for observation this packets and data. any help appericiated Thanks Dhaval -------------- next part -------------- An HTML attachment was scrubbed... URL:

hi can someone recommend a book about ISDN and SS7? I've been hacking asterisk for a while, but it'd be good to get some better background within things... thanks roy

Hi all, what is the signalling of IAX? Currently I want to connect two switch through IP using asterik signaling, and I want to transfer SS7 over IP (between the 2 asterisk), will IAX can transfer SS7 signalling through IP (like TDMoIP does) If no which solution can I use? see below the architecture switch1-------------Asterisk--------------------------Asterisk --------------------------Switch

Does anyone know of a device that will take an SS7 link and convert it to a PRI? -- respectfully, Joseph - (606) 477-2355 x140 ------=============

I thought everyone should know this. Jorge, After reading your page in the http://voip-info.org/tiki-index.php?page=Asterisk+SS7 please advise Your U.S. customers that SS7 is not done the same way as in the rest of the world and the requirements are different. The U.S carrier's require 2 redundant links. I know this first hand because we run an SS7 network. CARDOSO Jorge Miguel wrote:

When are 'we' going to have this solution Steve? :) You keep talking about it, and we keep asking when it's going to come about. I know myself, SS7 will be a make or break for our continued use of Asterisk. Even if we had some price indications would be good, and/or a timeframe? Don't want to seem pushy, but it's been on the cards for quite some time now. Ben -----Original

I'm making outbound calls by placing call files in the asterisk outgoing directory. At times, the call would be hung by SS7 without even attempting (due to error in the outgoing number). I get the following on console: -- Attempting call on ss7/9297210213 for s at croom:1 (Retry 1) -- Sent IAM CIC=22 ANI=9134904821 DNI=9297210213 RNI= -- SS7 hangup 'SS7/callserver/22'

Hi all, I'm being requested to deploy an?IVR service?using SS7. I've deployed Asterisk before using ISDN connection, but never with SS7. Can anyone explain me the different between using ISDN and SS7 ? What need I do now to change to use SS7 ?. Many thanks, Giang -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

Hi, Does Asterisk support SS7? Google shows an old new post from Feb. 2002 stating that OpenSS7 would help add SS7 support to Asterisk, but presently OpenSS7 seems to be dead and I can't seem to find anything about it at Asterisk or Digium's sites. What happened? -- Regards, Tais M. Hansen ComX

Hello.. I have a customer who wants to connect 2 PBX's over IP.. The setup should look like this: [PBX] <-- SS7 --> [Asterisk] <-- IAX --> [Asterisk] <-- SS7 --> [PBX] Since there are no SS7 cards , I was thinking at a way of carrying the E1 data as bulk...Can I do that ? How ? Is possible a scenario like this ? I'm thinking of IAX because I don't

Hi, there are still some questions to be answered by OpenSS7.com in order to decide, whether E400P-SS7 is a good choice for the asterisk SS7 support. In the meanwhile I'm also in negotiations with another manufacturer (whose name I currently may not tell due to a NDA) of SS7 hardware, who gets likely persuaded to offer a cheap SS7-PCI-card which would be suitable for asterisk. Asterisk users