similar to: IAX trunk monitoring

Hi, I just upgraded from 1.2 to 1.4. In 1.2, when I did a "show uptime" I used to see a second line telling me the time since the last reload. Has this been removed in 1.4? The following is the output of my two test boxes: Connected to Asterisk 1.4.18.1 currently running on voip2 (pid = 10605) Verbosity is at least 3 voip2*CLI> show uptime System uptime: 15 hours, 55 seconds

I'm having some trouble with placing some iax calls over an openvpn: Setup A is a 1.8GHz Celeron, T100P attached to a Zhone Zplex. Setup B is a 266MHz P2, T100P attached to a Zhone Zplex. Setup C is a 700MHz P3, T100P attached to an Adtran TA 750. Setup D is a 233MHz Pentium, with an X100P. Setups A and B are on the same physical network. IAX calls routed between them work fine. Setup D is

I constantly get the following error messages in /var/log/asterisk/messages: Dec 8 10:52:57 WARNING[1009521664]: File chan_iax.c, Line 3324 (iax_ack_registry): Received unsolicited registry ack from '192.168.0.1' Dec 8 10:52:57 WARNING[1009521664]: File chan_iax.c, Line 4181 (socket_read): Registration failure Where 192.168.0.1 is another asterisk server. Below are the local and

Hi I have an account with mynetphone (australia), which gives me two voip (sip) accounts, which i used to have connected to a spa9000. this is behind a firewall, so on the spa9000 I would listen on another port apart from 5060. so on the firewall 5060 would go to voip1 and 5061 to voip2. I moved to asterisk (+tdm410) and the machine was also the firewall and I had no problem - well atleast it

I'm looking to use * for a HQ/branch office topology with fairly few calls over the WAN. The questions I have all pertain to the following architectural pic: http://www.45891.com/misc/arch.jpg I'm looking at a distributed architecture so users are somewhat functional when the link to HQ is down, with a centralized voicemail server to allow for transfer of voicemail messages from user to

I have successfully configured two servers and I am now trying to connect via iax. When I attempt to call from one ext, 2006(server viop1) to extension 3006 (server voip2) I receive a timeout or "call failed 403 forbidden. The information I am receiving from the console is below. Apr 26 10:53:32 WARNING[311313]: channel.c:1745 ast_request: No channel type registered for 'IAX'

My VoIP provider allows me to have more than one call outbound on the same line simultaneously, for some reason. I am pretty sure that they do not want this to happen, so I'd like instead to limit each line to one call. I do not want the users to have to dial another prefix to go out on another line. Is there any way to add multiple accounts for my _9. extension and have Asterisk

I have the following pair of macros defined to handle outbound calls from *. Rather than specifying full dialstrings in the main body of extensions.conf, outbound dial commands are made using a macro call as follows: Macro (outbound,number_to_dial,callerid_to_present,gateway1,gateway2,gateway3,gate way4) The final gateway defined is nearly always a fallback to PSTN if none of the IAX or SIP

Greetings, DIAX seems to work well placing calls, but I can't actually receive a call . Here, DIAX (x305) "registers", then I use a sip phone to place a call to DIAX (which definitely is not in use by me at debug time, but it is idle on my desktop.I think), and then * goes to vmail. Here's the debug output: affinity*CLI> iax debug IAX Debugging Enabled Rx-Frame Retry[N/A]

Good morning, I am trying to use the Windows iax client. My iax.conf looks like this: [general] port=5036 bindaddr=10.1.3.111 bandwidth=high allow=gsm ; Always allow GSM, it's cool :) tos=lowdelay [pos| type=friend context=default auth=plaintext secret=pos deny=0.0.0.0/0.0.0.0 permit=10.1.3.0/255.255.255.0 host=dynamic defaultip=10.1.3.2 In the registrations dialog

Hello, I'm french, so excuse my poor English. I'm face to a terrible thing, with has stole a lot of my time. On the .184 machine, I've the following iax.conf : [general] rtcachefriends=yes bandwidth=high tos=reliability jitterbuffer=no autokill=yes #include "iax.voip1.conf" #include "iax.renoir.conf" The iax.voip1.conf file contains : [VOIP1] type=friend

Hi, I'm trying to get zapras do work, I had downloaded the pppd-source and the 2 patches. I succefull compiled and install the patched version of pppd, but got this error in message-log Jul 15 11:43:32 voip1 pppd[9296]: In file /etc/ppp/filters: unrecognized option 'active-filter' Jul 15 11:43:57 voip1 pppd[9299]: Plugin zaptel.so loaded. Jul 15 11:43:57 voip1 pppd[9299]: Zaptel

Hi All I'm trying to get two Asterisk servers to talk to each other using IAX(2). I've read the WiKi and the docs and tried the examples..... I can't get it to work (I have 2 x 7960's registering on one server and 1 x 7960 registering on the other). I've set them up as follows... The two servers are set up as friends and have consecutive IP address's. The setup is

I am having trouble getting Asterisk to compile the zaptel stuff. Here are the specifics: Linux Kernel 2.5.9-42.0.8.EL Asterisk 1.4.0 I compiled libpri, zaptel, asterisk and asterisk-addons (in that order). This is a fresh install of CentOS. Following the CentOS install, I did "yum -y update" until there were no updates left. Here is my src directory: drwxr-xr-x 24 root root

This *should* be something that's easy to fix, but apparently I'm not doing something right. Our SIP long distance provider is telling us to only use formats G.723 and G.729, so I've set up their trunk configuration in sip.conf as such: [t564] type=friend host=XXX.XX.56.4 context=default disallow=all allow=g723 allow=g729 However, the Dial application gives the following error:

Hey, all... If this is too off-topic, I'd be grateful for directions to a more appropriate mailing list. I'm trying to set up Asterisk and some Sipura boxes. I've got an SPA-3000 which is registering twice with Asterisk - once for its FXS/Line1/VoIP1 and once for its FXO/PSTN/VoIP2. My eventual goal is to have inbound calls on its FXO ring four times on its FXS and then fail over to

Hi, I created an iaxtel account, and was given a password containing an "@" character. The directory pages imply that they change the web login password only. How do I reset my IAX password so that it is usable in the iax.conf file? Thanks, Steve

We have IAX2 peer between two asterisk and I am getting following error following IAX2 WARNING. IAX calling is functional [May 10 15:23:34] WARNING[2056]: chan_iax2.c:3487 __attempt_transmit: Max retries exceeded to host 172.24.146.51 on IAX2/orasebcam-612 (type = 6, subclass = 11, ts=3030332, seqno=211) [May 10 15:23:44] WARNING[2047]: chan_iax2.c:3487 __attempt_transmit: Max retries exceeded

O, try the following.   Test this first. ldd /usr/sbin/hfaxd  if you getting libpam.so..  something, then hylafax is compiled with pam support.   Next,   apt-get install libpam-ldap   ( just to be sure, i do believe you have installed it already )   create the file :  /etc/pam.d/hylafax Add :   auth         required       pam_ldap.so account   required       pam_ldap.so

Running * with default config files except for sip.conf. Any call made is dropped 5 seconds after connection, with the following messages: Mar 17 16:37:41 WARNING[1009461760]: chan_sip.c:495 retrans_pkt: Maximum retries exceeded on call 6C94C1B1-77C4-11D8-91FB- 000A95DA04DA@192.168.1.152 for seqno 48221 (Response) == Spawn extension (default, s, 5) exited non-zero on 'SIP/2000-6bd7' Mar