similar to: IAX with dynamic echo cancellation - what do you think?

Hi, I just got a T1 interface for a AT&T (became Lucent) System75 (uses same cards as Definity). I would take a crack at making a cable but can't determine the pinout for a cable and it is not apparent from the board. Asking you guys makes sense as one of you may have one of these systems. The cable has a amphenol male D50 connector on one end and probably a rj45 on the other. I also

I would like to access VoiceMailMain2 skipping extension and password prompting if calling from a resource that has a mailbox defined. What variables can I use to retrieve the calling channel & calling extension (if it exists)? Here is what I'm trying to accomplish (of course ${CallingResourse.MailBox} is not a real way to retrieve this info)... exten =>

I have a machine that crashes every so often. I believe the following macro is responsible (gotoif,$[${ARG3}] in particular). The macro works as expected: if ARG3 is defined - hop over assignment. But my hunch is that it gradually chews up memory. ; This macro is puts voicemail in an alternate mailbox (if ARG3 defined - otherwise Mailbox matches extension). [macro-stdexten] exten =>

Here is something I wrote years ago. I expect you can adjust it for your needs # cat remove_blank_vmail #!/bin/bash # remove_blank_vmail takes arguments as voicemail boxes and removes messages with audio files shorter then MINSIZE (in bytes) #---------------------------------------------------------------------- # Description: # Author: John Harragin Monroe-Woodbury CSD # Created at: Thu Nov 6

Hi, We are looking at consolidating our lines with PRI. This will allow the elimination of many fax lines. Some of them will be replaced with this type of config ... PRI * IAX * Channel-Bank FAX We will have daggressor suppressor enabled. Is anyone doing this and should I expect smooth operation? John This e-mail was scanned and found clean by Monroe-Woodbury CSD Antivirus.

Hi, I'm buying an interface for my Toshiba DKT424 to connect to *. Initially it is a trial to route internal calls over our wan. Think of it as a tie trunk between 2 pbxs. I expect to get PRI from the telco our layout will be like this: telco_T1_PRI to * to various PBX or TDM or IAX to * to other pbxs My question is, is there benefits to connecting with PRI over a standard T1 within my

I just called 6610 from Zap/1 exten => 6610,1,Dial,Zap/1&Zap/2 (Don't try this with the handset pressed up against your ear) ...is this the call waiting indicator? Is it a file, can it be turned down - and does it get used anywhere else? These are both fxs ports. In zapata.conf changinging to callwaiting=no stops this. The text implies that this affects fxo ports. John This e-mail

Hi, I'm looking for 4 line phones that will see some heavy usage (they need to be tough) for office secretary/receptionists. Any recommendations? One additional consideration (not particularly for my current needs) is regarding the page/intercom feature that can be mapped to one of the analog ports - does anyone know of a 4 line phone that will do this? Thanks, John This e-mail was

Hi, I am setting up a hylafax server. From what I've read so far, hylafax supports CID numbers and names but currently does not support DID. I assume I can do something like this... [40faxDIDs] exten => _87[5-8]X,1,SetVar(CALLERIDNAME=${EXTEN}) exten => _87[5-8]X,2,Dial(Zap/g${hylafaxMODEMGROUP}) ...and use the CIDName variable in hylafax to route the faxes to the appropriate

I am ordering T1-PRI service from local service provider and have a few questions. Is there framing and coding considerations (or is it all one standard), if so what is best? How are calls routed based on DIDs - are these just dtmf tones passed after the call is picked up and treated as normal exten=> definitions? John This e-mail was scanned and found clean by Monroe-Woodbury CSD

Hi, Can I make e&m wink start lines just wait for digits - instead of going to default? Someone else cleared a similar problem (as described below) on an fxo port with "usecallerid => no" but it is not doing the trick for me. In this case the line when straight to default which would be ok also. John I posted the stuff below about a week ago... I set up a t1 from my sys75 to

Hi, I set up a t1 from my sys75 to asterisk. After much experimentation I got it to work as e&m wink start. If dialing the trunk access code from the sys75 (a 5 - this is stripped on the s75), asterisk picks up and provides dial tone immediately. Here is the problem, after about 3 seconds that line switches into s,1 of the default context. If I dial (5)1234 very fast - before the switch to

I have a T400P in my main building M and am going to put asterisk boxes in two buildings A & B. I already have our wan on fiber running between the buildings (including some extra strands) and the distance is beyond straight Ti distance so I would need csu... to use copper. It occurred to me that I could use TDMoE - and it may be less costly. My assumption is that the best to avoid the

What mp3 formats are being used for good quality sound and reliable playback for 'music on hold'? What bit rate, sample rate(8000hz?), mono, etc? This e-mail was scanned and found clean by Monroe-Woodbury CSD Antivirus.

Hi, I'm getting a situation where 2 of my trunks (loopstart pots) are occationally bridged together (3624 Newbridge channel bank - asterisk signalling=fxs_ks for trunks) and are staying off hook until I do a 'soft hangup' on one of them. When I listen on a butt set each of the lines are silent (or at least by the time I find them). I am guessing one of the end users isn't properly

A couple of weeks ago I posted a message entitled 'Bridged trunks stuck off hook' about a situation where 2 of my trunks (loopstart pots - but Centrex) are occasionally bridged together. It has occurred to me that what may be happening is that a line hung up by Asterisk might quickly be reused and if the time interval is right, the telco will interpret this as a hook-flash. Is there a way

I notice the zaptel Makefile option the mark2 option & KFLAGS+=-DAGGRESSIVE_SUPPRESSOR is now gone. Does simply adding these options still compile in a certain echo can - or is there an other method of activating a particular can. I have not had to update my machine that is connected to pstn for a while & I don't want to jump into echotraining without a way to quickly enable what has

I have been having periodic trouble with mpg123. I have tried .59r & .59s and perhaps others a while back and still get the 'broken pipe' and zombie mpg123s (although I think I saw something about a fix in the changelog) once and a while. Is it currently possible to configure moh to run directly on the wav files? Now-a-days hard drives are so big, why use compression at all (at least

New complile causing trouble... How do you enable MARK2 echo can with DAGGRESSIVE_ SUPPRESSION? looks like zconfig.h ..but I have quite a bit of echo on a bridgeded call and echocancelwhenbridged=no John ------------------------------------------------------ This message was sent using Monroe-Woodbury's WebMail. http://webmail.mw.k12.ny.us/ This e-mail was scanned and found clean by

I think the solution may exist. The compatibility of mysql-connector-odbc with maria may just means the driver can access the mariadb - but my experience suggests not live on the same host. maria has its own connector: https://downloads.mariadb.org/connector-odbc/ it does not look like this is in the sig, so I'll have to turn to the maria repo. I'll try replacing the driver first, then