similar to: IAXTEL/ Dial problem

Ok folks I have another question. So far I have gotten my IAXTEL number and I have been able to make calls from my asterisk system to any IAXTEL number and even to FWD numbers. I also got FWD to work and I now can get calls to my main system. It's great when these things work. But when I call my own IAXTEL number 17005441100 all I get is a message saying the user is un registered or un

Ok here is another problem I have run into. I have a Sipura 2000 and I have been able to configure line 1 with only one small problem. But I can't get the line 2 working with asterisk. Here are samples of my sip.conf and extensions.conf. If I disable line 1 I can then get line 2 working. Is there a sample configuration for the Sipura to get both ports working with Asterisk. Sip.conf

I just got 2 IpDialog phones for use with my Asterisk system. I have been able to get the phones to just dial local extensions but it is not able to register with my system correctly. I would like to know if someone has set these phones up before and how they did it! Is there any examples for use with Asterisk? They seem simple enough to config with there web interface. Thanks

I have 2 Snom 200 and would like to get them to work properly with Asterisk. With the Firmware 2.02t I am able to use the phone. But only one line configured. With there newer firmware 2.03o it will not allow me to make calls. But I can get calls on the unit. Again the 2nd line is not able to be registered. Is this an issue with Asterisk or Snom? I could use some example configuration

[ Sorry, I incorrectly copied some Reference headers into this post and tacked it onto the wrong thread. -Steve ] So far, I have been able to receive incoming iaxtel calls via my assigned 1-700-xxx-xxxx number, but only when using md5 authentication in iax.conf: [iaxtel] type=user ; Incoming calls only context=incoming auth=md5 secret=<mysecret> ; Required for

Ok I know that I am new user and would like some information on how to register to use IAXTEL. I looked at the gnophone web but it does not tell me how to register or where! Yes I am very new to Asterisk and Linux so please help. I did a google on this and kept sending back to the main site IAXTEL but I feel lost! Also can someone explain what top posting is? I don't want to do this on your

I would like to know if anyone has come up with a script for 911 dialing rules that put correct information on our locations. We have our office in 3 different building one being our production & shipping dock. It is almost 2 blocks away. We are connected with Ethernet Wireless between the buildings and have Sip phones setup in the other 2 locations. All the phones are working just fine.

Hi, I've been setting up * recently and slowly getting to grips with it, however I'm getting rather confused with all the different configs for IAX calls, FWD calls iaxtel etc etc. What I think I need it a basic understanding or even a comparison of these different voip systems (if thats what they are?) I'd like to be able to make calls to other voip users, both in the UK and abroad

I'll admit it. I'm a asterisk newbie (but no stranger to telephony). The setup is simple: two Grandstream BudgeTel 100 phones (SIPPhone specials) on a private segment calling to a Linux box acting as the segment's firewall with a leg on our public network. The phones are setup as SIP/phone1 (x1000) and SIP/phone2 (x1001), respectively (thanks to the Asterisk HOWTO). Getting IAX

Hi all I've been trying to make * work with IAXtel to no avail, all seems ok in the config but am not getting anywhere This is what I'm getting from console (user/pass/dest # changed for obvious reasons): DEBUG[1133735216]: File chan_sip.c, Line 3841 (check_user): Setting NAT on RTP to 0 DEBUG[1133735216]: File chan_sip.c, Line 4891 (handle_request): Check for res for phone1

I didn't get any response at all to my last "request for status" on IAXTEL. So, when this happens, I attribute it to one of a number of things: 1. No-one knows. 2. No-one cares. 3. Everyone knows, but are too busy to reply. At any rate, my investigative side kicks in and I began searching thru the digest's I've gotten, looking for references to IAXTEL. Mostly it is

I would like to prevent * from dialing 900 and 976 numbers. I setup the following settings in extensions.conf. But this does not seem to work! I don't know what I am doing wrong please help! exten => 1900XXXXXXX,1,Congestion exten => XXX976XXXX,1,Congestion exten => XXX976XXXX,1,Congestion exten => 1XXX976XXXX,1,Congestion exten => 91900XXXXXXX,1,Congestion exten =>

I need to get 2 Asterisk servers working together. I have been reading and doing just about every example I have been able to find here on the list and the Wiki. It's now gotten to the point that nothing on box2 seems to be working. I seem to have a major problem understanding the format. Here is what I have so far. It's 3 days of hair pulling and nothing seems to work! Asterisk box 1

Last night Mark and I made some changes to the IAXTEL tollfree outbound, and inbound access. The inbound access number has changed to: 248-724-0700. (This number is in Pontiac, MI Ratecenter, and is supplied by Telesthetic LLC, a next gen phone compnay) This number will say "Please dial your number now" at that point you can dial your 1-700-XXX-XXXX IAXTEL number assigned. In the

I am trying to get the following phones for testing. Is there a distributor in the US that is able to sell me these Sip phone and ATA adapters? I can not afford the Cisco phones there too hard to configure and too expensive! 1 - Sipura SPA-2000 2 - Grandstream Sip phone BT-102 1 - Grandstream HT-286 1 - Snom 105 Sip phone. I have called and emailed chagres but they have not reply. Nor

I tried to connect my * to IAXtel, but i always get this errors. chan_iax2.c:5849 socket_read: Registration of 'mnetwork' rejected: Registration Refused On dial a iax number i get: chan_iax2.c:5526 socket_read: Call rejected by 69.73.19.178: No authority found chan_iax2.c:5528 socket_read: Immediately destroying 3, having received reject chan_iax2.c:2411 iax2_hangup: We're hanging

I have a problem that sometimes lines will go into what I call never never land. The Asterisk system will put a line with <Zombi> on it when you type show channels it will make the analog phone line dead. And on the CLI it says: astsvr*CLI>Zap/1-2<ZOMBIE>(macro-twoline-exten,s,1)Up Dial Zap/1-2|20|r I have tried to release it with soft hangup Zap/1 & also soft hangup

Has anybody had a problem registering their IAXtel account? I just signed up for an account and followed the documentation on iaxtel.org and my registration is always rejected. When I type "iax show registry", I get the following output: Host Username Perceived Refresh State 12.37.165.130:5036 xxxxxxxx <Unregistered> 60 Rejected

On Sun, Aug 17, 2003 at 03:44:21AM -0500, Gnophone Support wrote: > Hello, and thank you for registering at gnophone.com. Your login > information is listed below: > > Username: miernik > Password: ******* > IAX Phone Number: 17002916107 > > Please login as soon as possible to > http://x.linux-support.net/directory/ to complete the

Is anyone other than me having trouble dialing out via IAXTEL? I havn't changed my config files in weeks but seems that IAXTel calls (800 and FWD) stopped working in the past week sometime. Robert