similar to: IAX2 Trunking confirmation?

Hello everybody! I'am just leaning Python and wanted to write something useful for me, an recursive masstagger for ogg-vorbis files. My script uses pyvorbis 1.3 from the Debian testing tree. so far here is my Problem: The pyvorbis bindings aren't documented. As i understand the pyvorbis package, this is a simpe 1:1 mapping to libvorbis. dir(pyvorbins-oject) gives me an refernece to an

On 03/11/03 00:25, Mark Spencer wrote: > As a side note, I strongly would like to see someone implement a > client using libiax2 which implements IAX2 instead of the (now > obsolescent) IAX version 1. I'm implementing a Java-based IVR server (and yes, I know Asterisk does IVR, and no, it's not flexible enough to do what I want and no, it doesn't integrate well with the Java

Im having problems setting up a trunk between two locations. Heres the setup I have: Server A is connected to the PSTN at my datacenter Server B is connected to a clients e1 line at his datacenter I only want to route calls from Server B to Server A and out through the PSTN. Server A has a lot of other things connecting to it, so I need a very specific context for all calls to go through.

I have 1 * box having x100p installed and the other has no zaptel card at all. both of the * box has compiled in ztdummy module and both have been activated by modprobe ztdummy. When using trunk to connect the 2 *box. The one without zaptel card complaint about unable to accept trunked packet: no matching peer. On the one has zaptel card I have tried to remove the ztdummy module and connect

Hello, For those of you who have solved the learning hurdle of rails deployment, all I can say is congratulations! I''m struggling, frustrated that my app, which runs so well on my linux box, generates such odd errors on my vps and completely fails to do anything. For example, at the moment my production.log file has the error: ActionController::RoutingError (No route matches

Hi List, I have a 2Mbps SDSL link which gets saturated during peak time because about I have about 3 E1 worth of g729 traffic going thru. So I'm planning to use IAX2 trunking to reduce bandwith requirement and squeeze out each and every bit of this (expensive) bandwith. I've set up two boxes (debian etch), one in a remote data center (which has plenty of bandwith) and one behing

Hi Is anyone successfully using iax2 trunking with CVS head ? The reason I am asking is that I have heard there may be some audio problems, which I would like to know about before sending customer's calls over a iax2 trunked connection. Thanks in advance. Clive

Two cvs-head asterisk boxes with iax2 working fine (without register statements). When two calls are placed simultanously from system A -> B and the packets are sniffed on the wire, I see the two calls using two different udp packets. At the top of iax.conf I have trunk=yes and jitterbuffer=yes (at both ends). I was expecting to see both calls handled within a single udp packet, but

Hi, Anyone using inter Asterisk trunking IAX /IAX2 ? Thanks, Geo ___________________________________________________________________________ Appel audio GRATUIT partout dans le monde avec le nouveau Yahoo! Messenger T?l?chargez cette version sur http://fr.messenger.yahoo.com

Hi I was doing some bandwidth testing, and my incomming usage is 36% more than my outgoing bandwidth. The setup is IAX2 trunking using GSM codec. Is there any obvious reason I am overlooking to figure out why there is such a big difference between the two.? I am using CVS-head September 3rd, maybe there is a version skew? Any suggestions will be appreciated. Thanks Clive

I am curious if anyone has had problems trunking iax2 with 100+ concurrent calls. I am planning on testing this out tomorrow, however I wanted to know if anyone else has had a problem with this prior to my test so I know what to look for if anything is known and what resolutions have been found if there are any known problems. Specifically I am doing this on fbsd 6 with asterisk 1.2.4 using

IAX2 now has support for a "trunk" mode ("trunk=yes" in the appropriate friend section). Trunk mode allows IAX2 to use bandwidth extremely effectively. The original impetice (and strategy) was a result of a mistake in which it was claimed that Asterisk with a T100P could send 96 simultaneous calls over a single T1 using VoIP. Thanks to a suggestion by the customer, combined

Hello, Would like to use IAX /IAX2 to transport 30 channels inter Asterisk. I don't have any experience with that, so can someone help ?? How much bw do I need for simultaneous calls and is there any latency for SIP G711 to IAX2 and vice-versa , ... etc ? Thanks in advance for any info, Geo ___________________________________________________________________________

I've been using NuFone with Asterisk for a while, but I've started seeing this error with incoming calls: NOTICE[114696]: File chan_iax2.c, Line 4581 (socket_read): Rejected connect attempt from 216.234.116.189, requested/capability 0x4/0x4 incompatible with our capability 0xff03. Outgoing works just fine, but I can't get incoming to work at all. Any ideas? I googled for the

I have a quick question regarding accounting rules. This is the contents of my accounting file. *for reference eth1 is my net interface eth0 is my loc interface ezp:COUNT - eth1 129.15.70.46 tcp 80 ezp:COUNT - 129.15.70.46 eth1 tcp - 80 smag:COUNT - eth1 129.15.70.24 tcp 80 smag:COUNT - 129.15.70.24 eth1 tcp - 80

We spent some time yesterday trying to understand how IAX2 authentication works, and now I'm confused... Let's say that the receiving end has this entry in their iax.conf file: [remote-site] type=user secret=foo auth=md5 context=incoming host=dynamic The way I see it, there are two ways to initiate an outbound IAX2 connection to this system: 1) Use Dial, as in:

All, I''m trying to do some documentation on the models for our interfaces team. I espcially need them to be able to see the relationships belongs_to and validations. However, I must be stupid with rdoc because I can''t seem to get those two things in the generated documentation. Ideas?

Hello, I can use directed call pickup using pickup application (between sip, iax, skinny cals), but unable to pickup call that is ringing on phone behind h323 gateway (using original h323 channel in asterisk), is this even suported? thx PJ exten => _*7.,1,Pickup(${EXTEN:2}) console log, when trying o pickup ringing line 324 (h323), from skinny phone (953) -- Executing

On Tue, Sep 6, 2011 at 4:37 PM, Matt Pharr <matt.pharr at gmail.com> wrote: > I'm seeing some behavior that surprised me in writing an <8 x i1> vector to memory and reading it back.  (Specifically, the surprise is that I didn't get the original value back!).  This happens both with TOT and 2.9.  This program illustrates the issue: > > define i32 @foo() { >  %c =

I'm seeing some behavior that surprised me in writing an <8 x i1> vector to memory and reading it back. (Specifically, the surprise is that I didn't get the original value back!). This happens both with TOT and 2.9. This program illustrates the issue: define i32 @foo() { %c = alloca <8 x i1> store <8 x i1> <i1 true, i1 false, i1 false, i1 false, i1 false, i1