similar to: Dlink DG-104S (chan_mgcp) and configuration w/Asterisk

I am trying to dial a mgcp extention from my sip phone and i am getting this error message. anyone got any idea? error I> -- Executing Dial("SIP/2204-5dc2", "MGCP/aaln/1@10.0.1.150") in new stack May 19 22:30:01 NOTICE[1251156800]: chan_mgcp.c:1104 find_subchannel: Gateway '10.0.1.150' (and thus its endpoint 'aaln/1') does not exist May 19 22:30:01

When I try to connect to * using a Cisco ATA 188 configured with a MGPC firmware (v3.1.1), I just keep getting this message every 30 seconds or so : May 10 10:08:21 NOTICE[7913]: chan_mgcp.c:1509 find_subchannel: Gateway '192.168.1.27' (and thus its endpoint '*') does not exist Using tcpdump, I have checked that the ATA188 (with IP 192.168.1.27 and port 2427) sends UDP packets to

Hi. I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk with the next configuration files. '--------------- extensions.conf ---------------------------------------------------- [general] static=yes writeprotect=yes [globals] ap1 => mgcp/aaln/ap200@64.76.148.186 [macro-apl1] exten => s,1,Dial(${ARG1},30,Ttmr) ;exten => s,2,Voicemail(u${MACRO_EXTEN})

Does anybody has the expirience configuring Asterisk with Cisco ATA 186 MGCP firmware ? I have Cisco software v3.1.1 atamgcp (Build 040629A) Asterisk 1.0-RC1 On ATA i only put domain test. mgcp.conf looks like this [test] host = 192.168.195.55 context = default line => aaln/2 line => aaln/1 Asterisk CLI shows this: Jul 31 16:05:40 WARNING[135449600]: chan_mgcp.c:485

I'm not sure that the problem lies in the NAT because the phone is talking to Asterisk. I'm hoping this is a simple config thing I've overlooked but I've tried all kinds of combos inside the [] in my mgcp.cfg file. The phone's IP is 192.168.1.116 (my comp is .110). The router to which the phone and my comp is plugged into has a WAN IP of 10.0.0.28. All the other comps (and SIP

Okay, so I'm a noob. Asterisk looks very promising, so I say "thanks" and "good job" to all who contribute. My * test box is up and running with soft phones using IAX and SIP, so now I'm on to testing hard phones. I borrowed a couple ShoreTel 210 phones from somebody who had them on hand but they only support MGCP. I see that there's an mgcp.conf in

Hi all, I have VOIP network built with MGCP endpoints.The manufacturer of endpoints is ASKEY. I downloaded latest Asterisk software and found it very useful for me. I configured it and it seems taht everything works OK when I am testing it with one or two endpoints. After that I tried to move Asterisk to working network and replace existing call manager. It starts working and calls are

Hello, Sorry for posting again my question about MGCP Phone and Asterisk But I can't use it. I'd like to know weather it is a pb of my confiuration (mgcp.conf), My IP Phone device or asterisk. I include my mgcp.conf file and may send some debug trace. Thank you for any feedback. Best regards, Daniel ANDRE ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr =

Hello, I have just received an MGCP Phone for test purpose and I can't place a call from my MGCP Phone. I can call my MGCP phone from a SIP Phone. Here is my mgcp.conf: ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr = 0.0.0.0 ;[dlinkgw] ;host = 192.168.0.64 ;context = default ;line => aaln/2 ;line => aaln/1 [192.168.10.10] host = 192.168.10.10 context =

Hello, Anybody has it working with asterisk? Could you share your experience ( good/bad) Thank you -- Anton Yurchenko<phila@dg.net.ua> Digital Generation

Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ... TRUNK=H323/BYEXTENSION@pstn_gw ...

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes

Hi, in following of a recent discussion I got to work on MGCP with the Cisco ATA186 again, and got it to work very nicely. However, there is a little thing with transfers I would like to get comments on: Call comes in from PSTN and goes to an ATA186 (MGCP) Call is answered and then, using flash, transferred to another extension If the extension is available, there can be an announcement and

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306

Hello, I've successfully installed Asterisk from last CVS and configured it for using with DLINK-DG104S as mgcp CPE and PGW2200 as external sip server. All are work fine at G711 codecs, but then I disable all codecs except g729 some calls failed (Not all calls. Some calls passed at g729 succesfully). All my devices configred to use only g729 and I don't see other codecs at mgcp or sip

Hi all, i want to use authentication in h323.conf. How can i use it ? In the h323.conf is writed : "If you wish to use Authentication you need to set the appropriate auth keyword above" Where and how i have to set this keyword ??? I've tried "auth=yes",but it does not work. Thanks for Help, Thomas.

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb: