similar to: Dialogic/4

I just found a Dialogic VFX/41JCT-LS (4 analog ports) in a drawer. I can use it in my house with asterisk at home project. Can I use that with asterisk? Where can I download proper drivers? -- ------------------------------------------- Erick Perez Linux User 376588 http://counter.li.org/ (Get counted!!!) Panama, Republic of Panama -------------- next part -------------- An HTML attachment was

Hi All, I currently run asterisk in our office (in Japan) and use a cisco PRI gateway for connection to the PSTN. I would like to setup some more systems for our smaller offices (in Japan) that would use BRI and preferably using a PCI card in the asterisk box and not a seperate Cisco gateway (expensive). HOWEVER, Japan has this INS64 protocol for their BRI lines and im not sure what cards

Hi all, I just checked out that Asterisk which is a platform I am interested of. I would like to install it to the Linux box for a trial. I have some legacy Dialogic hardware on hand, don't know they will work with Asterisk or not. For analog loop start interface I have Dialogic D/41 E which is of ISA bus with four Telco interfaces. Will it work on Asterisk? Best regards, Patrick.

Hello all, I found a LSI161SCREV2 Dialogic board in one of my drawers, and i was wondering if by any luck, i could make some magic happen with asterisk ... If asterisk does not support it, is there any PSTN to H323 or PSTN to SIP gateway that support this dialogic card and that can be connected to an Asterisk Box? Digium, I PROMISE that I will buy my cardf rom you once my tests are conclusive

Please rest assure that I have been following the * development for a while and understand the value the Digium hardware gives me vs any other vendor. Most of the people on this list probably know whats good for everyone else, but I like to find out for myself (I am not a CNN junky). Now the * site mentions Dialogic as supported hardware at: http://www.asterisk.org/index.php?menu=hardware It

Is there ant chance of the Dialogic card model D/4PCI working with asterisk ? Best Regards Steve Beaumont

Steven Critchfield <critch@basesys.com> wrote: __________ >On Wed, 2004-05-26 at 14:23, tpanton@attglobal.net wrote: >> On which subject, has anyone else >> got time to work with me on a chan_dialogicGC ? It looks do-able but I am ignorant of how asterisk does threading. > >Do you have GPL drivers for the dialogic card? Follow previous comments >about licensing.

Hello all Asterisk Users, This is my first post here. We are in a process of moving Dialogic 240/JCT-T1 from old voicemail server to Asterisk box. Which card drivers do we need? Please share experience if anyone have successfully configured Dialogic JCT-T1 card with asterisk? Only source proves that this card work with * http://lists.digium.com/pipermail/asterisk-dev/2003-April/000244.html

Hi All, I have checked the supported hardware list of boards that will work with Asterisk. What I am curious about is whether or not I need to have the Dialogic software installed and loaded before I launch Asterisk. Thanks. Jim

Clients are Windows 2000; server is running Samba version 3.0.2a. We've been a W2K shop for some time but have started to get in a few Windows XP systems (principally laptops). The issue we're experiencing with the Win XP machines is that they can't map the homes share, either through a VPN or when connected directly to the network the samba server is on. All other shares remain

I found an old Dialogic card in an abandoned PC, that I think is a Dialogic D/41EPCI based on some googling.. The lspci output says: 00:09.0 Bridge: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01) Subsystem: Dialogic Corp: Unknown device 0529 I'm just getting started with Asterisk to build a SOHO system. Any suggestions for what I can do with this card? It would be

I''ve submitted a few patches on Trac to help get Merb running under JRuby [0][1][2][3][4]. It''d be cool if any of you committers could find the time to look them over and apply/reject them. They''re mostly tiny, so it shouldn''t be too onerous. With all of these patches applied, there are still 3 spec failures. One is in the spec ''a merb mailer

Dear All I am trying to use svychisq with a two-dimensional table 4 x 5. The command I am using is summary(svytable(~dietperception+dietstatus,dudleyls1rake,na.rm=TRUE),"C hisq") It is throwing up an error message as follows: Error in NCOL(y) : only 0's may be mixed with negative subscripts In addition: Warning messages: 1: is.na() applied to non-(list or vector) in:

Aloha, I have an application to build an eight conference bridge for a Norstar. I would have a converter to turn the digital ports into analog with disconnect supervision. On the digium site I only saw a single port FXO card. I would like to use a higher density FXO card like a D/41 or newer from Dialogic. I noticed in the handbook 2 (draft 3/30/03) that there is a price to use dialogic cards

Hi all, I am have an R script that makes many plots, and I would like to string them into a movie file. To do that I have to save all of my plots as jpegs or gifs. I don't want to go through all of my plots and save them by hand though. Is there a way to automate saving the plots as a gif or a jpeg so I can string them into a movie? Thanks in advance Matt Oliver

Hello, I just wanted to know if any of you has successfully (or know about) installed the Dialogic 4xFXs ISA CARD D/41 ESC? Does it work with *?, if so, how is the driver called? Thanks a lot for your comments. Alejandro Acosta,-

Can someone share pointers to Asterisk's Dialogic support? Which boards are supported, driver status, and etc. Thnx

Hi all ! What is the current status of the Dialogic channel driver ? Is it available ? Is it commercial ?? Any info ? Thanks

Hello, Has anyone had any luck getting a D/41D ISA dialogic card working with *? Thanks Jason This message along with any attachments is intended only for the use of the individual or entity to which it was addressed. It may contain information that is confidential and prohibited from disclosure. If you are not the intended recipient, you are hereby notified that any dissemination or copying of

Hi list, Anyone knows where I can get information about configuring a Dialogic card to run with Asterisk?? The model I have is D/120JCT-LS. Somebody told me that I had to buy the driver, but I don't know if this is true and if so, who, how and how much...