similar to: Problems with TDM400P & X100P

I can not seem to get Samba and diald working together. Whenever I log in to my Windows 95 computer and it tries to map my drives to the Samba server diald dials and then the drive does not map. If I wait a minute or so and then right click on Network Neighborhood and do a find computer my Samba server shows up. I can than log on to Windows again and it maps the drive fine. Or I can unload diald

Yes, I know this is lame, but my location limits me to using a dial-up ISP. I am running asterisk with a T100P and a TDM400 card. I currently have dial-on-demand setup on the same box, using diald and an external modem. To prevent DOD from trying to dial out during an external call, I have an AGI script kill diald before initiating a call, and then restart it at the end of the call by looking

I'm in the process of converting from a dedicated file/print server to a Linux box running Samba. Among other things, this box currently supports our Internet gateway via IP Masquerade. It uses demand dial (diald) at the moment, but will probably be converted to a full-time connection at some point in the near future. I've been asked if it is possible for the Samba server to be accessed

Hi all, I hope that i've posted this in the correct place. if not, please accept my apologies (where should this go?) I have carried out experimental removal of bivalves at 2 intertidal shores. Bivalves were removed by raking of surface sediments. I wish compare the biomass values of for a total of 8 species between the 2 shores My 3 treatments are: Undisturbed Controls (Cont), Procedural

I used the "FreePBX on Debian" HowTo at http://powerontech.com/freepbx-on-debian.htm to install. I use callfiles to initiate calls to my SIP carrier. They get my registration, but they see that my call is interrupted before they can complete the connection. My Asterisk log shows that the call times out after the time (45s) specified in my dialplan Dial() command. What is wrong? [from

channel_still_open() does not count "larval" channels as open. If the server sets up a protocol 2 connection with no remote command (as with "ssh -N ..."), the "server-session" channel remains larval, and the server exits as soon as it notices that there are no open channels besides this one. Typically, it exits right after the first use of a port forwarding closes.

Hello - The final schedule for the Asterisk birds-of-a-feather meeting (as an adjunct to the VON conference) in Boston looks like this: Tuesday, September 23rd at 8:15 at VinnyT's of Boston near the Hynes Convention Center. We'll try to get a corner booth in the "downstairs room", and look for the guy wearing the blue button-down shirt with VON logos on the breast pocket

A non-text attachment was scrubbed... Name: not available Type: text Size: 2910 bytes Desc: not available Url : http://lists.samba.org/archive/samba/attachments/19990608/1b2f9b97/attachment.bat

I have a Solaris 10 update 6 system with a snapshot I can''t remove. zfs destroy -f <snap> reports the device as being busy. fuser doesn''t shore any process using the filesystem and it isn''t shared. I can unmount the filesystem OK. Any clues or suggestions of bigger sticks to hit it with? -- Ian.

Good Morning-- I'm looking to shore up security in my system and with communications. Can you point me to the proper version of GnuPG for CentOS 5.3 (Final)? Thanks, Dick -- "They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety." --Benjamin Franklin 1755

On a 7.2 desktop system I see irregular attempts to start the fingerprint authentication daemon "fprintd". One of the messages is "D-Bus service launched with name: net.reactivated.Fprint" This fails as there is no fingerprint device. fprintd.service is disabled. Without a fingerprint device, is this software needed. Yum removal (aborted) shows no packages dependent on

On a CentOS 7 system I'm trying to install lightdm. Yum says it requires "glib2(x86-64) >= 2.50.3". glib2 2.46 is installed but I have not found a 2.50 version. Have I overlooked it in some repo? -- Jon H. LaBadie jcu at labadie.us 11226 South Shore Rd. (703) 787-0688 (H) Reston, VA 20190 (703) 935-6720 (C)

I am looking to only sync directories not any files within them.. Is there a switch/trick available for this in rsync ? Thanks for any suggestions !! Tim Nelson Senior UNIX Systems Administrator OSI Support Services, Inc. 2520 N. 170th Street New Berlin, WI 53151 T: 262-780-2134 F: 262-780-2050 E: tim.nelson@osioutsourcing.com Outsourcing services are primarily performed by OSI

Hello, I have the contour of the shoreline of a lake. I have measured data points away from the lake shore signifying a particular depth. The data is not ordered as a polygon and hence trying to draw it creates a series of lines all over the place. I would like to turn the points into a ordered set that results in a smooth polygon. I have tried a "nearest point" approach. An example

Hello, I am trying to figure out if there exists some R command that allows one to be particularly selective when reading a file. I'm dealing with large fixed-width data sets that look like 539001.. 639001.. 639001.. ... 539002.. 639002.. ... Presently, I am using read.fwf to read an entire file, but I am interested only in reading those records beginning with 5. I have been unable to

On Fri, Jan 27, 2017 at 06:05:54PM +0100, Leon Fauster wrote: > > Am 27.01.2017 um 17:27 schrieb m.roth at 5-cent.us: > > > > Johnny Hughes wrote: > >> On 01/27/2017 09:19 AM, Jon LaBadie wrote: > >>> With a large update to be made, eg. the 900 package > >>> one I questioned yesterday, are there any suggestions > >>> to avoid possible

hey list! I am attempting to shore up some centos machines (ranging from centos 5 to centos 5.4) for pci compliance by changing the port that nlockdmgr listens on to function under a privileged port. So what I did was try to hardcode the port by editing /etc/sysconfig/nfs # TCP port rpc.lockd should listen on. LOCKD_TCPPORT=1011 # UDP port rpc.lockd should listen on. LOCKD_UDPPORT=1011 #

Anyone familiar with the selinux policy for the amanda backup software package? I'm getting lots of data not being backed up. For example, under /home there are 2 directory trees owned by root. Those get backed up, user home dirs do not. No AVC denials nor messages in /var/log/messages or journalctl log. But if I turn off selinux enforcing, or set amanda_t type to permissive, complete

hey all 'scp -r ' follows symlinks. IMO this is a bug and should be changed - it: a) hampers the use of scp. As it stands, I cannot use 'scp -r' because of this behavior. If someone links to '/', or if I hit a recursive symlink, I'm screwed. b) It is inconsistant with cp. When you 'cp -r' on a file, it does NOT follow the symlink. When you scp

Okay here is my setup: Gentoo Box running 2.6.4 w/ 4 NICs 1 NIC is for internal network 3 NICs are for external network The machine has a static address assigned to the internal network nic. This nic runs dhcp and dns forwarding. The other 3 nics have external dynamic IP addresses. All will have the same gateway. There are 3 NICs because this is a very large pipe, that will only allocate a