similar to: Problems reloading

G'Day, I have a bit of FireFly problem that hopefully someone has seen before. What happens is if I make to or receive a call from the FireFly network the call will connect successfully. However, around 10 seconds after I answer the call I am disconnected. The weird thing is same thing happens if I make a call. I've had a look at the * console and I can't see that my * PBX drops

Beginner to Asterisk, but not beginner to VoIP FreePBX front end running on a dell 1550 and XLite running on a different Woindows XP box Both boxes connected via switch on same subnet. No NAT involved On FreePBX I created a new extension 1001 with a SIP password of 1001 On Xlite, username is 1001, password is 1001, authorization user name is 1001, and domain is IP of Free PBX XLite tries to

Asterisk version 1.2.14 I use snom190 and xliteV3 as sip phones. asterisk send the rtp stream never to the xlite softphone. Any hits for me? *CLI> rtp debug RTP Debugging Enabled -- Executing Dial("SIP/xlite-007918f0", "SIP/snom") in new stack -- Called snom -- SIP/snom-00797110 is ringing -- SIP/snom-00797110 is ringing -- SIP/snom-00797110 answered

Hi there, I have tried very hard to setup the x-lite with asterisk, but until now i didn't get sucess. When i start the asterisk in debug mode, i see the message: sip/2.0 401 unauthorized. I know that this problem with authentication. I put in my sip.conf as below. [2203] type=friend username=2203 auth=md5 secret=1234 reinvite=no canreinvite=no dissallow=all allow=gsm

What's the secret to getting sound through Xlite? The SIP messages all look OK to me, but the sound isn't coming through. It was trying to use GSM, so I searched the archive and tried: disallow=gsm allow=ulaw Now it says that it's using ULAW but I still get no sound in either direction. Phil Skuse (MBJEJPIEUI) <phil.skuse@vicorp.com>

G'day, I've just downloaded the tinc-1.0pre3 and compiled it - it seems to work fine. I tried your tinc start script in the redhat directory, first adding the MyOwnVPNIP = 10.1.3.1/16 VpnMask = 255.255.0.0 to my tinc.conf file as suggested. But now when TINC is invoked, tinc exits with the following error. [root@platypus tinc-1.0pre3]# /usr/local/sbin/tincd -n wurley.vpn Failed to

Does anyone have any views on the best software base SIP client to use that normal users could use with Asterisk without being too techie ? I have tried the X-Lite client with varying success. The first version worked OK but music on hold broke the voice paths and the slightly newer version initiated the call but failed to make the voice connect in both directions. The SJphone client works but

Hi, I've got an Asterisk box with grandstream and xlite clients on it. No here's the thing: - I grey out all the codecs on the Xlite except for GSM - I call the Grandstream from the Xlite, the Xlite uses the GSM codec and the Grandstream uses ulaw, with Asterisk doing the conversion, everything fine - I call the Xlite from the Grandstrea, the Xlite ends up using the ulaw codec as

I have been using X-Lite on FWD without any troubles and recently became interested in trying asterisk. I am able to register from X-Lite and dial a number - I've tried dialing some of the sample numbers in the sample extentions.conf file, like 500 and 1234, they appear to dial correctly from X-lite but nothing else happens - no audio is heard. My understanding is that I should hear some

Dear All, I have downloaded the xlite version 2.0 for windows and I made the following conf in the xlite itself as the document suggested in order to make it work with Asterisk but still it doesn't work as a matter of fact when I tried to make a tcp dump I can see no packets going between the windows client and the Asterisk server at all, here is the my conf on the xlite itself: in the

I've beaten myself bloody dealing with this one... No luck so far. In summary, incoming calls from Gizmo establish, but neither get nor send sound. Outbound calls to Gizmo work fine (well a bit choppy but work) My thought is that the SIP connection is being made fine, but the RTP is getting stopped / blocked / misdone somewhere. Here is the thing: Asterisk 2.5 on Linux (No hardware

Is it possible to run Samba on Xp Pro Regards Deon

Hello, I'm trying to place a call to asterisk using X-Lite. Asterisk is setup with some Grandstream phones. I can call from one grandstream extension to another. When I try to an extension with X-Lite, it comes back with Status of SIP/2.0 404 Not Found. X-Lite is not registered as asterisk extension. It is just sending a sip invite to extension@IP. Does the X-Lite need to connect to

Hi all, I have my asterisk setup as following: IP 2 x E1 x-lite <-------> Asterisk -------> PSTN When I place a call from x-lite to PSTN, the quality of the sound in the direction x-lite -> PSTN is very bad. That is, the voice of the x-lite user, heard by the PSTN user is choppy and makes communication not very pleasant. The sound is choppy as if bits of data

My first Asterisk install: Debian sarge with the 2.6 kernel, and two X-Lite soft-phones. I followed the online how-to documents and was calling between the two soft-phones and calling the demo system with no problems and had full audio. I then went on to configure the TDM400P's two FXS modules. I got into that a ways and was having some success, but no dial-tone when I was off the

Hi all! I'm new to asterisk and I'm trying a simple config with: - Debian GNU/Linux (unstable) - last version of Asterisk - a X100P card I have a problem with dial out from a SIP software phone (XLITE) to a public number (ex. my mobile phone), asterisk start the call, but nothing happen... If I run "ztmonitor 1" I can see the right RX level and if I try to make a call with an

Dear all, I have tried to run an asterisk instance together with XLite on a single machine (a PowerBook). The intent is to take advantage of IAX connections to easily cross NATs while traveling. While the IAX setup proved 'easy', just having to fiddle a little with working configs at both sides, I did not succeed so far in getting XLite to connect to the local Asterisk server, AND be

Ok, at the bottom of my h323.conf file on my 1st server I have this: ; --------------------- [test] type=user host=209.237.227.185 context=termination-test incominglimit=10 accountcode=005 ; --------------------- Using an Asterisk at the other IP, I have this: exten => _1NXXNXXXXXX,1,Dial(H323/${EXTEN}@64.135.11.85,,o) This should send a call from the test-server to the IP of the 1st server;

Hi list, I have 2 softphones, 1 Idefisk (IAX), 1 Xlite (SIP) registered to Asterisk. One call the other-one, is it possible to order Asterisk to force answering the call ? i.e. Xlite call Idefisk, Idefisk is ringing, I send a command to Asterisk which force answer, so Idefisk answer the call without clicking on "Accept" button. Greg -------------- next part -------------- An

Hi! I have a new problem with my SIP device.I have done some changes and now I receive continuosly a SIP message: "501" "Not impelmented" back from the SIP Gateway. I can see that it doesn't register to Asterisk. I have in the SIP device: Registrar 1: UnRegistered to: 2222 registrar: 188.208.12.237 5060 expires: 2000 name: gateway passwd: 123 My