similar to: T1 to T1 on asterisk?

Hi all, I'm looking for recommendations on ethernet switches for a new install. Ideally would want switches with at least 24 ports, ideally with a GE uplink, and that support PoE (power over ethernet) on every port. I've seen lots of switches, and lots of "power hubs", but the combination, which makes a lot of sense, seems rare. What is out there? Do the switches need to be

Hi all, While pondering my choices for local dial tone service via a bunch of POTS lines or a T1, I began to wonder if perhaps there is another way. Are there VoIP dialtone providers? That is, could I use only my internet connection for voice calls and not have a separate T1/POTS bank for that? I guess I am imagining a company that gateways between the PTSN and the internet backbone.

Hi all, This is a NEWBIE question, so all you experienced types that are tired of stupid questions can move on... I've pretty much given up trying to do my entire phone system over IP (including local service), so I have to select and provision my local CO lines. I need about 10-12 lines which can be POTS lines, of course. But, I thought, why not get something digital and expandable

Okay, I am facing a move in two months to newly renovated space. I have to decide *this week* between: A) Pull LAN and phone cables, prepare to move and expand our "traditional" PBX (Panasonic KX-TD1232 and VPS200). or B) Pull only LAN cables, go VoIP, use Asterisk as PBX. It is *not* an option to purchase a VoIP system package from Cisco, 3com, etc. Installers are getting an

Hi all, I would be most grateful if someone would review my plans for my new phone system and comment on areas of expected trouble and advice on what to do better. Instead of moving our Panasonic KX-TD1232/TVS200 system (ugh...) to our new location, we've decided to jump into IP telephony with *. But we are new to * (but not Linux), so we're trying to learn as much as we can before we

Hi all, I like to have a dial in modem on my toll free number so that when I or my employees travel, they can always get in for net access to read email if no better method is available. Right now, my Panasonic KX-TD1232D PBX receives the call on a POTS line and routes it to an analog modem. The speeds achieved are around 24 kbps due to the digitization of the KX-TD1232D introducing

Hello, I ftp'ed the binary RPM for samba from us6.samba.org, and when I tried to verify it, rpm said that MD5 was NOT OK. Has anyone else reported this behavior? Thanks, Hiten Sonpal sonpal@ciholas.com Engineer, CIHOLAS Enterprises Voice: 812 476 2721 x 102 2626 Kotter Ave, Unit #D Fax: 812 476 2881 Evansville, IN 47715 http://www.ciholas.com

I have a dilemma. I am trying to setup an asterisk setup for about 10 people, but with the ability to expand to 100s. We are looking into hardphones to use for our systems. Here are the requirments I am looking for: SIP Not POE Full duplex Speakerphone $100-$300 We would like to have the cordless and corded option if possible (at least for 3 of the 10 people). So here are the

I've been looking at the two phones Aastra 9112i and 9133i for our offices now. I was just curious if anyone could tell me about the ring tones. Specifically: 1) How many ring tones do they come with? 2) Can you upload your own ring tones? 3) If so, what format and how? (wav, mp3, gsm, etc. and TFTP, web management, flash, etc.) Thanks for any help. -- Tim DeBaillie 812-476-2721

Hi, Currently I only have 1 PRI which I am using for dial-in customers. The line is connected to a Portmaster3. I have never used more than 10 concurrent channels. The calls can be both analog or ISDN. It would be a waste to order another PRI for my Asterisk box. Is there any way of splitting a PRI into 2 PRI's of 15 channels each, or plugging the PRI into the * box and it send the data

We have been pretty much able to solve our echo problems, except for the primary mode in which we desire to operate our system. See system diagram at bottom. Prior to making adjustments to cancel echos (all echocancel=no): Call Type Result (Before) --------- --------------- CP <- LEC PRI * TDMoE * FXO -> AP

Greetings, I haven't upgraded my tree(s) for awhile. My last attempt to rebuild after an updating src && ports, resulted in nearly installing the entire ports tree, which is why I've waited so long. Try as I might, I've had great difficulty finding something that will _only_ upgrade what I already have installed, _and_ respect the "options" used during the original

# portmaster mail/dovecot-sieve ===>>> The dependency for mail/dovecot seems to be handled by dovecot2-2.2.22 ===>>> Initial dependency check complete for mail/dovecot-sieve ===>>> Starting build for mail/dovecot-sieve <<<=== ===>>> All dependencies are up to date ===> Cleaning for dovecot-sieve-1.2+0.1.19_2 ===>>> Waiting on

hi guys, I have a little problem maybe you can help ... I have an asterisk setup, with an E100P, and an ISDN-PRI 30 channel line from the telco going into it .. the E1 line is OK, because plugged into a Lucent Portmaster 4 it works OK .. plugged into the asterisk box I just get an engaged tone, and asterisk posts this message on screen : WARNING[1167272000]: File chan_zap.c, Line 5275

Due to trip to make, I will have to wait few days to upgrade my nodes to 9.2 release. But, I'd like to learn the easiest way to handle ports. Thanks to Matthew Seaman, I will try out txz repos, when I find the correct address for that. Otherwise, I assume portmaster might do the job equally well. Reading manual, I guess flags like -P -a or -PP -a are made to fit? Next to think would be to

Hi: The FreeBSD10-Beta3 kernel is recompiled successfully with the following in /etc/make.conf WITH_NEW_XORG=yes WITH_KMS=yes WITH_GALLIUM=yes But after installworld, there is no sight of new xorg-server-1.12.4 in pkg cache nor in /usr/ports: How to install new xorg and where is the source? # pkg search xorg linux-f10-xorg-libs-7.4_1 xorg-7.7 xorg-apps-7.7 xorg-cf-files-1.0.5_1

Hi, I''m interesting in CBQs.... :) (nice) Here at my ISP i''ve three Remote Access servers (2 TC ''Total Control'' enterprise Manager from USRobotics and one PortMaster). The first TC is with one range of IP 200.210.18.0/0 and 200.210.66.0/8 I knew the comand: tc filter add dev eth2 parent 10:0 protocol ip prio 100 u32 match ip dst

Here's one last plea for help from the list before I give up on the totally cool software FAX modem concept in complete despair (for now, at least, until I have more time to dig into it).... I am simply not able to successfully receive a FAX no matter what device I transmit from or how I bring the call into Asterisk. My lastest effort was a call from a Pitney-Bowes FAX machine into an X100P

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

Hi list, after the security announcement (http://www.freebsd.org/news/2012-compromise.html) I use svn to update my local ports tree. I've found out that the port index is not updated. What is the preferred/recommended way to update port indexes when using svn? Thanks, Serguey.