similar to: Speex & openh323

Hi, I am trying to post this again as I am getting no answers and the support@digium.com bounces... (I have searched the whole list and can't find the answer either) I have installed a 5 user license for G.729 and want to route calls through Asterisk from my G.729 phone to Cisco AS5300 also using G729. Both Cisco and the phone connect using this codec if I do not force the call to go

Hi, Ive been struggling with asterisk for a few days now. I understand pretty much how it works and how to tie things together (SIP -> SIP internally works fine etc), but just cannot get asterisk to work with an X100P clone (its a Ambient MD3200, if that means anything to you guys). I have tried (initially) asterisk 1.07 with zaptel 1.07, and now Asterisk CVS-HEAD with zaptel cvs. Both give

Hi, I have licensed the digium G.729A codec. But for some reason incoming and outgoing calls will ALWAYS use G.711a. When I force my phone to only accept G.729 then an incoming call from ZAP goes straight to my voicemailbox as the phone doesn't accept the codec Asterisk wants, even if I force it in sip.conf. Is there anywhere else I need to look to tell ZAP to use G.729 preferrably ? The

Hi, I am trying to replace my Cisco 5300 gateway with my new Zap TE405P card. Incoming calls and outgoing calls between my cisco and my SIP phone works fine on G.729. Recording messages in the asterisk voice-mailbox also works fine from both my SIP phone as well as PSTN -> Cisco -> Asterisk. I have licensed the digium G.729A codec. When I connect my ISDN PRI to my Zap card and I call

Hello, I have that problem with codec G729. Please can somebody help me! WARNING[16384]: File codec_g729b.c, Line 413 (load_module): Unable to initialize va stuff: -1 == Detected 4 licensed G.729 transcoders WARNING[16384]: File translate.c, Line 219 (calc_cost): Translator 'g729tolinb' does not produce sample frames. == Registered translator 'g729tolinb' from format G729A to

Hello, I've successfully installed Asterisk from last CVS and configured it for using with DLINK-DG104S as mgcp CPE and PGW2200 as external sip server. All are work fine at G711 codecs, but then I disable all codecs except g729 some calls failed (Not all calls. Some calls passed at g729 succesfully). All my devices configred to use only g729 and I don't see other codecs at mgcp or sip

Hello everyone. I am having problems getting speex support. It seems * is not loading speex. When i did a make in the codecs sub dir, the following error pops up when making speex: codec_speex.c:34:19: speex.h: No such file or directory is this file missing in the cvs as i just removed the whole * dir and did a new checkout and still seem to get this error, or do i need to get/install

Hi. I just tried updating asterisk and I guess I broke something. Here's the log: Unable to find a path from G729A to SLINR Unable to find a path from ULAW to G729A Any ideas on what I should try? I tried nuking all the zaptel stuff in the system and the source and started over agian. Also nuked the asterisk config files.... I saw this asked once before but there was no reply :-/

I have a ATA 186 with SIP firmware 3.1 when I changed the configurations to use the g.726 codec I received many erros and the calls doesn't work. I changed the fields: - LBRCodec: 6 <- the code for g.726 - TXCodec: 6 - RxCodec: 6 The errors: Jul 9 13:15:37 NOTICE[1192491824]: rtp.c:500 ast_rtp_read: Unable to calculate samples for format G726 Jul 9 13:15:37 NOTICE[1192491824]:

Original Post ---------------- I have an Asterisk related problem with mutualphone. I can connect to any number with any softphone that I am using (iaxcomm, SJPhone, and a few others). Also I have a Grandstream BT 101. But I cannot call (via Asterisk) to mutualphone destinations. Other destinations go fine. A working phone call (e.g. from iaxcomm) gives the following on the console: --

Hi folks, In an effort to save bandwidth (our 7905s run over a WAN) we've switched from ulaw to g729a. We purchased 4 licenses from Digium (4 SIP clients, low call volume), and they seem to have been accepted: [codec_g729a.so] => (Annex A/B (floating point) G.729/PCM16 Codec Translator) == G.729 Host-ID: 07:53:aa:d3:e2:f2:bd:cc:27:60:9d:5f:da:eb:5d:e9:6e:09:a1:4e == Found license

I have a pretty basic Mandrake 10.2 w/KDE 3.2 and I installed Asterisk-1.0.1-2mdk. I installed the source of main and contrib from ftp, so at the install time I accepted all the packages needed to be installed too. The installation went smooth, but when I try to execute asterisk (#asterisk -vvv) I encounter few warnings I end with an error. At this point I didn't touch any conf file, I was

I'm running 1.6.1.18 on an older ubuntu machine. I upgraded to dahi-linux-2.3.0. That went fine, and it works. But I decided to use the opportunity to upgrade to 1.6.2.6. That didn't work. configure, make menuselect, make, make install all went fine, or at least seemed to. But it hangs starting up here: [Apr 13 20:15:28] VERBOSE[1612] codec_speex.c: -- CODEC SPEEX: Setting

Hello, Can somebody tell me what does it means ? I just installed my codec g729 with two channels. [codec_g729b.so] => (Annex B (floating point) G.729/PCM16 Codec Translator) == Detected 2 licensed G.729 transcoders WARNING[16384]: File translate.c, Line 219 (calc_cost): Translator 'g729tolinb' does not produce sample frames. == Registered translator 'g729tolinb' from

Hi guys, Just installed G.729 (from digium) codec and after starting asterisk getting the following warning: [codec_g729b.so] => (Annex B (floating point) G.729/PCM16 Codec Translator) WARNING[1082809536]: File asterisk.c, Line 234 (listener): Select retured error: Interrupted system call WARNING[1082809536]: File asterisk.c, Line 234 (listener): Select retured error: Interrupted system call

Starting up the asterisk using asterisk -vvvc i get this error is this normal and i purchased license for g729 today? [codec_g729b.so] => (Annex B (floating point) G.729/PCM16 Codec Translator) Jan 21 17:31:58 WARNING[1082805040]: asterisk.c:255 listener: Select retured error: Interrupted system call Jan 21 17:31:58 WARNING[1082805040]: asterisk.c:255 listener: Select retured error:

Dear i have buy two license of G729 codec and i have install/registered as documented but after i start "Asterisk -vvvcng" i notice this warning and if i made call the CLI say "No compatible codec!" How can i solve this problem? Thanks in advance Dimitri ------------------------------------------ [app_datetime.so] => (Date and Time) == Registered application

Hi, I have a Cisco 5300 which I want to make a call THROUGH the Asterisk PBX (security) to an IP phone which supports g729, and vice versa. Both Cisco and the phone talk this codec if I do not force the call to go through * However if I say canreinvite=no in the sip.conf for either of these gadgets, the call will fail with No compatible codecs! I have bought a 5 user license just to

Hi, I write to this list, because I didn't find anything on the net. I installed asterisk using bristuff-0.0.2 without any errors, but when I start asterisk with "asterisk -vvvc" I get following error: [codec_ilbc.so] => (iLBC/PCM16 (signed linear) Codec Translator) == Registered translator 'ilbctolin' from format ILBC to SLINR, cost 127 Segmentation fault Removing

hi michael, here are the core dumps. only kphone works when 0.5.5 and * cvs. audiocodes and msn messenger all cause seg faults when calling ccm thru * (or vice-versa) ~kelvin [chan_oh323.so] => (OpenH323 Channel Driver) == Parsing '/etc/asterisk/rtp.conf': Found == Parsing '/etc/asterisk/oh323.conf': Found 0:00.004 OpenH323 Wrapper OpenH323 Wrapper