similar to: Analog lines

Rich Adamson <radamson@routers.com> wrote: > >> I have been investigating on this list and found that faxing is not >> reliable between Zaptel >> cards and that Digium does not support nor >> recommend fax over the TDMXXB interfaces. >> >> Is this true ? Will fax not be reliable enough for my customer ? > > True... the TDM card (or its drivers)

Hi, I am building for a customer an * solution that will use 2 Digium cards. 1 x TE110P (T1 ISDN PRI) 1 x TDM40B (4 analog ports, 2 for faxes, 2 for extensions) The system will be connected to the PSTN through the T1 ISDN PRI interface. All customer extensions will be SIP phones except 2 fax machines that will use the analog FXS ports on the TDM40B card. I have been investigating on this

I'm trying to see if this is even possible. When you dial ext 2000 I want it to ring my sip phone for 20 sec then call my cell and let it ring for 10 sec if I do not pick up the call on my cell I would like it to go back to * and leave a voice message for me. Here is what I have so far in my extensions.conf Everything works except the call will not go back to * after the 10 sec rule has

Hello All, The problem I'm facing is the following: two machines that require analog signal. However, connection to the world is setup as follow: T1 connection to Asterisk server Any suggestions on how to convert digital signal to analog? Type of card on my Asterisk server is wct4xxp Thanks for your support! Motty -------------- next part -------------- An HTML attachment was

Hello, I am using a perl script to pull call info from a DB and place calls via telnet and AMI, all on local machine of course. My problem is that I need to capture any response from the carier, such as this taht appears in the CLI: [Mar 1 12:55:50] == Using SIP RTP CoS mark 5 [Mar 1 12:55:50] -- Got SIP response 503 "No Circuit Available" back from xxx.xxx.xxx.xxx:5060 [Mar

Hello I have an office with a T1 that provides 4 (out of 8) analog PSTN lines thru an adtran board. I want to add 4 more analog lines. Currently I have a Digium TDM40B. I'm wondering what the best upgrade path is, where I define 'best' as the solution that is most likely to work without problems (like interupt conflicts) and work with my current echo tuning . I see my purchase

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.

Hi, I have the following problem. I have 5 phones behind the same nat (canreinvite=yes). it works fine to receive calls and to make calls. sound quality is good, so everything works fine. The poblem is that the phone behind nat cant call each other. It works if canreinvite=no. But i want to do this. Does anyone have an idea? Regards, cjk.

Does anyone know the best approach to take for handling 100 analog phones? It seems to me that a chassis like Carrier Access or Adtran would work. The chassis would do much of the hard work of converting the analog sound to data. Any recommendations on hardware for the chassis? ...Jeff

Hi, I am trying to parse a date (that is read in as a factor) and add it to a dataframe. The length of the parsed date is shorter than the length of unparsed date and I therefore cannot add it to the dataframe: > x [1] 20030807 20030807 20030807 20030808 20030809 20030809 20030809 20030809 [9] 20030808 20030808 20030809 20030808 20030808 20030819 20030819 20030821 . .

Hello, we would like to hook up analog modems behind an Asterisk server, and we're very interested in the experiences that others have made when attempting that. We assume that there are no inherent problems with modems in respect to the Asterisk software, but it appears that the FXO/FXS hardware restricts this kind of a setup to lower data transmission rates, is this correct? Currently,

Hello Asterisk fans, I try to connect an analog modem to Asterisk. The modems are connected e.g. to alarm systems or a cash terminals (POS). As PSTN-Interface I'm using a Wildcard TE110P (E1). Is it possible to connect the modems to an ATA? Which ATA I should use for that scenarios? Cheers Bastian ____________ Virus checked by G DATA AntiVirusKit Version: AVK 17.1806 from 04.01.2007 Virus

It is possible to connect ADTRAN TSU 600 VP24 FXO 24 Port Channel Bank to Asterisk ? Somebody offered me that hardware, but I do not know if thats good hardware for Asterisk. rgs, Bartosz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030820/4a9e4608/attachment.htm

Did anybody know, Is it possible to establish a ISDN DIAL up Connection and Analog Dial up Connection (V90) trough asterisk with Digium TE405? Thanks a lot for help. Nico Giefing -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060328/3b657058/attachment.htm

Advance apologies for the length of this mail; I have an ISDN PRI supplied by NTL (ex Diamond Cable, Nottingham) which is currently working happily with an SDX Index phone system. I have to replace this phone system shortly and I've been trying to get a * system working for some weeks now. I have configured the dial plan (which works) and all my SIP extensions (which all work) along with

I've been trying to get a Win 2000 RAS server working with my asterisk PBX for quite some time, to no avail. I've googled, I've tried loads of configurations, I've rewired phone lines, and still I am not winning the battle. Here's my config. PRI->T400P->Asterisk->T400P->Adtran 750(L36 Firmware)->RAS Server. I have 4 Zap channels signalled FXO_KS to the 750

quick question how do i tell winbind to use PAM to authenticate user against 03 AD? vi /etc/pam.d/samba #%PAM-1.0 auth required pam_nologin.so auth required pam_stack.so service=system-auth auth required pam_winbind.so account required pam_winbind.so account required pam_stack.so service=system-auth session required pam_mkhomedir.so

hello! i've tried to use asterisk 1.2 beta version and all installed fine except that when i config asterisk to run at bootup it gives me an error which says 'execvp:Permission Denied!' then the loading fails so i stil has to start asterisk manually when i've logged in as root which is too much work, i want asterisk to initialize immediately on bootup. can someone help me in

Hello I am new to the samba world and have problem with my samba installation I can't use profiles for my Windows Clients (XP/2000) Version: Samba 3.0.22-13.18 of SuSE 10.1 I use Samba with openLDAP and smbldap-tools. For these progs it looks like all perfect (I can login from the Clients). I try to use Samba as PDC for my Windows Clients. The Clients can logon to the PDC and I also can

In the past we have used Adtran Atlas 550's to break out FXS ports for devices like modems. The great thing about the 550 is that internally it is all TDM so there is absolutely zero latency. We are able to use ATA's for faxes and analog phones but devices that use modems, they fail 99.99% of the time when using an ATA. We tried to migrate to TA908 devices; they have FXS ports built