similar to: Registering SIP with FWD and ICONNECTHERE

Hi ;) I'm a french newbie and i installed asterisk 1 day ago. I've got an ATA186 and a computer with Sjphone installed. If i want to call the sjphone from the ata or call the ata from de sjphone everything is ok. My problem is ,that i can't call the voicemail or any other phone number ..as 600 for exemple from the ata or the jphone. I don't know why but i looked after a long

Hi all, This is my first post here - I started with Asterisk a few days ago and have "fallen in love" - fantastic product. I've only got softphones connected at the moment - I'll probably order the FXO/FXS cards in about a month (and then think about getting some hardware SIP phones). Our current phone system is quite a few years old and isn't growing with us (when a single

I am going to have to find a fix for this problem or I'm going to have to quit using iconnect. About one call in 10 or so, iconnect's gateway gives me an error (console output appended below). So upon receiving the error, which as a 4XX error means, "Fatal," asterisk gives up and drops the call. But not iconnect!! The phone at the other end starts ringing, and rings

Hi friends, I've noticed that first register message sent by * always get rejected by the destination sip server. Then * sends a second registration message ( with Autherization section, and that get accepted by the destination host). Why is this ? Isnt there a way to tell * to send with Autothorization message the first attempt ? Asterisk sends this first 9 headers, 0 lines 11 headers,

Hi, I just got a SPA-2000 in and was finally able to complete my asterisk setup. I'm making my outgoing calls through iconnecthere from the asterisk server however I'm running into a problem when placing calls. I can connect fine but when the person (or answering machine) picks up I hear them talk for a about half a second then there is a half a second pause or muted period and then the

Hi All, I am trying to use iconnecthere to make outbound calls. I am behind a linksys router. I keep getting this error 481 "Call Leg/Transaction Does Not Exist". Does anyone have any prior experience with this problem. Any leads will be much appreciated. Attached are the conf files and logs #SIP.CONF ; SIP Configuration for Asterisk [general] port = 5060 ; Port

Hi folks, I want to fix hole in my asterisk set up. I use Vocal as my sip proxy and * for voice mail and the g/w to PSTN, Iconnect, fwd etc. So from Vocal I redirect sip requests which needs to go 'other' places. This senario works fine. Now the issue is someone else running a vocal or another SIP proxy can redirect his calls to my * as well. Those calls two will come through general

Hi. I cant make SIP calls from asterisk. When I start asterisk, I get the following message: What does it means?? Asterisk is not behind NAT or Firewall. ---------------------------------- [chan_sip.so] => (Session Initiation Protocol (SIP)) == Parsing '/etc/asterisk/sip.conf': Found Sep 16 09:52:33 WARNING[16384]: chan_sip.c:8477 reload_config: Unable to get IP address for

Hi All, I can only seem to get iconnecthere working with incoming calls intermittently. One minute it seems to work, and the next it doesn't. I am not aware of anything being changed in the config files. Outgoing calls work ok all the time. The Asterisk box is behind NAT so that does complicate things slightly. However, the Iconnecthere PCPhone client software works perfectly for

I am seeing some very peculiar things in the routines that REGISTER my * server with several accounts. I saw this on my console: . . . NOTICE[5126]: File chan_sip.c, Line 1878 (sip_reg_timeout): Registration timed out, trying again NOTICE[5126]: File chan_sip.c, Line 1878 (sip_reg_timeout): Registration timed out, trying again NOTICE[5126]: File chan_sip.c, Line 1878 (sip_reg_timeout):

This morning, I received a very strange error message on the Asterisk console. The error occurs when I try to access iconnect WARNING[196621]: File chan_sip.c, Line 386 (__sip_xmit): sip_xmit of 0x80d0854 (len 649) to 213.137.73.178 returned -1: Bad file descriptor I also get this error when I try to reload: WARNING[16384]: File chan_sip.c, Line 5355 (reload_config): Unable to get IP address for

Hi guys I just registered an incoming number with iconnecthere and I'm trying to set up incoming calls from icconnecthere on my asterisk server. I took a look at john todds sample sip.conf and extensions.conf file but for some reason my incoming is still not working. At this point I wish to use iconnecthere merely for inbound calls. Also my asterisk server is behind nat. The following

Hello All, I have gone thru all the resources I could find on google on asterisk + iconnect and managed to get outgoing calls working. However, I cannot get incoming calls to work at all. With the sip debug on, I can see that something is happening everytime a call is received from iconnecthere, but I get an invalid tone on the caller side. The call never rings anywhere on the asterisk. Would

Hi, I wish to connect several ATA186 Phones to each other, to iconnecthere and to the PSTN using asterisk. Please tell the appropriate settings for firewall (ports to open etc.) sip.conf and extensions.conf(part relevant to iconnect). Also I would be glad to get a working example of your ATA186 configuration. I tried searching the mailing lists and several sites but did not find an answer.

Hi, I have a deltathree account and I can place calls but I can't receive calls. I use Grandstram sip phones. When I call my deltathree phone # the voicemail is answer :(( I need some help and solutions from the guys who allready are using deltathree. I search on Internet and I try all types of configurations... :( This is my configurations files: - sip.conf - [general] port = 5060

Hi guys i signed up to iconnect a few hours ago to try do some cool stuff. but im having a few problems. Im running asterisk and xp/xlite softphone.. both xp box and asterisk box are on public ips. The problem is that when i ring anyone in the world it'll ring they'll pickup and i can hear them 100% perfectly/clearly.. but they cant hear me.. occasionaly they can hear something like a

Quick question for the experts: I'm seeing stuck SIP channel(s) scheduled for destruction stay open. This appears to happen after (apparently successfully) registering with a SIP peer. Any ideas where to start digging into this? I'm running today's CVS, however the problem existed before and does persist. Thanks, Kai-Uwe Example: (registration with iconnecthere.com) ast1000*CLI>

When I make a call using sip, I get the line NOTICE[327696]: File rtp.c, Line 292 (ast_rtp_read): Unknown RTP codec 19 received Repeated many times on the console ; SIP Configuration for Asterisk ; [general] port = 5060 ; Port to bind to ;bindaddr = 0.0.0.0 ; Address to bind to context = outgoing ; Default for incoming calls allow=gsm allow=ulaw

This may be slight off topic, but perhaps it has relevance: My iconnecthere account no longer works for "inbound" calls through NAT using the standard configuration that they provide on their website. I have sent them a message, but I believe it will be flushed down the toilet by the first-tier support people. When I call my iconnect number, it goes directly to voicemail. There

silly me, I thought the inbound would be the hard part. how little I knew... can someone please give me any insight into why outbound is not working, in fact why trying to enable outbound fouls up everything? I'm using asterisk, most recent from cvs, I'm behind a nat, and I'm trying to use iconnecthere.com for outbound and inbound. Inbound is working fine, no problems. But for