similar to: Semi-newbie question "Softswitch" and Asterisk - Is there a difference?

Dear List; I am trying to create a link between Asterisk and My softswitch, the link to be SIP Trunk. I did the below configuration and I do not know if any one can help me and advise me to have better configuration to be sure that link is fine. But I do not know how to determine the SIP username to be sent for my softswitch as sometimes the softswitch need to check it. Also, does asterisk

Dear all what is softswitch what is difference between asterisk and softswitch ?? regards satish patel --------------------------------- Catch up on fall's hot new shows on Yahoo! TV. Watch previews, get listings, and more! -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello everybody, Im new to the list and also new to asterisk, Im wondering if I could set up asterisk as a softswitch, I guess for what I've been reading that It could be possible but almost all the info and documentation Ive found so far is about asterisk as a PBX, etc. Im willing to set a small voip wholesale traffic bussiness and Im not quite sure asterisk is the right chocie for that.

Hello averybody, I'm looking the softswitch in digium website, anyone test the softswitch? Best Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20071202/2440f782/attachment.htm

Dear Alex; Thanks alot for your nice help. This is if I need to let Asterisk register with another softswitch (so I used register =>), what if I need asterisk to send call for the softswitch without register to it (directly)? If I removed the register => then how it will distiguish the IP address in the "host" at the [sip_trunk] is the IP address of the softswitch that need to

Hi List; If I need to do a trunk between Asterisk and another SIP softswitch (so Asterisk will send a SIP calls to that softswitch), then I have to configure this on the sip.conf file or where exactly? And is it the same when I configure iax trunk? Should I determine the context in this case for this SIP trunk? Regards Bilal

I'm confused a bit about the following and was hoping to get some answers on this group - What is exactly implied when we say asterisk can connect to a PSTN. Does it mean connecting to the PSTN via PRI/T1/E1? If yes, then I assume asterisk does not need to do any SS7 signaling and all it does (playing the role of a PBX) is to connect to a Class 5 Switch at the CO. Is this a correct statement?

Pardon my ignorance, but I was hoping someone could clear up something for me. - For a few POTS lines, digium has a single port card for that, or a T1 card to a channel bank. - For 10 or more lines, digium has a T1 or E1 card for that too based on PRI channels - For 100's to 1000's of lines, I suspect a soft-switch is in order??? A traditional phone company will sell: - POTS lines for

hi all i have a te110p installed in my system with a lot of Echo.. i decide to install the oslec echo supressor but when y try to add the module i have this problem. [root at asterisk zaptel-1.4.7.1]# insmod wct1xxp.ko insmod: error inserting 'wct1xxp.ko': -1 Unknown symbol in module [root at asterisk zaptel-1.4.7.1]# some advice? thanks. -- .-

As an example....if we have a call that: 1. originates via PSTN line to one of our local DID's in Seattle 2. comes into our Asterisk server in Los Angeles or Denver 3. is routed by Asterisk for termination back to a different Seattle PSTN ....and if our VOIP call termination provider requires (in order to get their best rate) all calls to go through their Nextone

Hi, has anyone connected Asterisk to Cirpack softswitch sucessfully ? Any howto or more info about needed Asterisk SW and setup ? Thanks in advance, regards, Rob.

Hi All; Alot of softswitches or PBX's does not accept to manipulate any SIP call without being registered firstly. So that means, I need asterisk to register firstly then I can route my calls to that SIP trunk. In IAX2, we use the register => , so what shall we do in Asterisk? And how its format will be (if we will use register)? Or what is the solution? Regards Bilal

Hi All, I want to use Asterisk for VoiceMail for a softswitch. I can dial in to leave voicemail and retrieve. Now there are many SIP Endpoints registered to the Softswitch. The Asterisk is sending a NOTIFY msg to the Softswitch on <ip addr>:0 Somehow Asterisk Looses the port from where the INVITE came in, this NOTIFY msg is not going out of the Asterisk, I cannot see in Ethereal.

Hi All, I've been experimenting during this weekend with asterisk as a softswitch, talk about me being completely lifeless, but let not talk about that. I've been conducting some really funny tests, trying to get an optimal SoftSwitch functionality. Here is my current setup: Source: Windows XP Pro + SJphone Box 1: Asterisk running in PassThorugh mode Box 2: Asterisk running in

I'm having problems getting Asterisk SIP to register with an Entice softswitch SIP Gateway. My provider tells me that all thats needed is a user name, password and the IP address and to register and it needs to be using MD5 authentication. I continualy get a "603 Decline" message. The provider of the gateway says they are not receiving any authentication information. Registration

Im trying to get my asterisk box to register to a sip provider without much success. here is my console output in asterisk Dec 13 12:57:17 NOTICE[213005]: chan_sip.c:3982 sip_reg_timeout: Registration for 'voicemail.nexband.com@metaswitch.nexband.com' timed out, trying again -- Got SIP response 403 "From: URI not recognized" back from 208.149.73.5 Urgent handler in my

We would like to know if you have any recommendations for softswitchs to be used by a small size telco with sip services in *.

Hi, did anybody ever try to make asterisk 'switch' calls on pri interfaces? My goal is to set up * to 1. wait on incoming calls until an extension is matched, 2. dial out and then 3. "pass through" the signaling until the call is either established or released I found that asterisk would first pick up the incoming call and then dials out. For my application however this

Has anyone setup SIP services with ss7 and lis trunks? If so .. what was used hardware and software.. we're trying to do a SIP -> pstn setup and not having much luck as QWEST keeps pushing dates off (aka trying to screw us over) for our pri lines due to the recent court and fcc activity in regards to unbundled switching and I'm looking for solutions/ideas involving SS7..

Dear All, First, I am not so much experienced in Asterisk. I need asterisk to route the call to soft switch when the caller is not in its extensions list. And also when routing to soft switch, a number 4327 has to be added in the caller's number and then routed. I think its not so hard in asterisk. Please help me. Regards, Pratik -------------- next part -------------- An HTML attachment