similar to: Odd output from X100P

I installed Asterisk as per instructions in the FAQ on the digium.com site. Double checked it. I also think they have a bug in the zapata.conf where the context should be incoming and not internal. 1) I hear no dialtone when I pickup the phone on the S100U. Asterisk sees the event and displays the message on the screen. I tried dialing but nothing happens. I hangup and * shows the hangup event.

Hi, I'm trying to setup Asterisk on a Linux (redhat 8) machine. There are no analogue phones to be used & use is purely for internet traffic (SIPs). I've followed the setup guide from : http://www.automated.it/guidetoasterisk.htm But cannot get asterisk to run. If I type asterisk at the command prompt I get invalid instruction If I type ./asterisk start I get [FAILED] Can

Hi, I have resources available to host a portal specifically for the Asterisk system, to help correlate documentation, FAQ's and How To I am new to Asterisk, and my hardest work is in locating information on using or configuring the software. Would Mark, John or any of you feel this would be of benefit to host? I am offering a PHP-NUKE portal for this, (Unless you know of a better

I know in the x100p hardware the driver can sense whether there is battery voltage on the line or not. Is this possible in the zap drivers using t1/e1 interfaces ? I believe the signalling bits are only ring and hook, not loop presence, so not sure if it is possible. I had a situation last night where a main cable was cut in the area and lines were down overnight. My burglar alarm knew right

Hello- I'm using the "accountcode" field in cdr table to store some temporary information used by my perl scripts. I'm finding that the field seems to be truncated to 19 characters, even though the allocated field in the table is larger (varchar(45)). Anyone familiar with the asterisk sources know where I can make a change to keep this from happening? ie: to allow more

Do they fall under FCC certification if they're built to the same specifications as the ones from Digium? If I build my own T100Ps from the schematics and board layouts that are available, are they legal to plug into the PSTN?

I have the dev kit lite installed, and after compiling and installing asterisk, I've become a little confused about how and when wcfxo and wcusb are loaded. When ever my box is done booting, the wcusb module is loaded, but the wcfxo module is not. Further, even though my startup notices say that asterisk started OK, it is not running by the time I log in and do a ps. First, where are the

If asterisk is running as a daemon (started with no command line options), can I reconnect to it and get the vvverbose info in the console? In other words, will asterisk -rvvvc work? Sorry to ask.... I would just try it to see if it works, but I don't have an installation handy and have to do some remote troubleshooting soon. ThanksE+06. D. __________________________________ Do you

Hello, I have had several instances over the last month of Asterisk freezing, sometimes after 12 hours, sometimes after 8 days. The common elements are that: - all Zap channels lock[hangups don't register and no new calls in or out] - no new in/outbound calls can be made on Zap or SIP channels - people who are still connected to calls can continue to talk - in the CLI interface, you can

Hi I received the Asterisk Dev Kit Lite on Saturday and got a small PBX working fairly quickly using the config files supplied with the kit. This was on my desktop machine and the sound card stopped working. I turned the system off and moved the sound card to another slot to give it a different IRQ. On reboot, the modules zaptel, wcfxo, and wcusb all load OK and asterisk starts OK but there

Has anyone integrated Asterisk for Voicemail with a Nortel Meridian phone system or know if this could be done? Thanks, John Haigh

Hi, I am running * with E100P board. At least every our I got an Error 500 message and ISDN-PRI restarts: Jan 10 12:53:02 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 12:54:27 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 13:33:01 WARNING[98311]: File chan_zap.c, Line

Hi all- Over the past week or two, I've been trying out asterisk under Fedora 1 Linux (RedHat). In my setup (single and dual Xeon motherboards), I have so far had a very good experience in terms of performance. In doing E1 load testing, I've found that Fedora handles heavy load much better than RedHat9, probably because of its better use of the multi-threading capabilities of the Xeon.

I have a number of Zap/ extensions defined in a queue with ringall strategy. When this queue is called sometimes Asterisk seems to think that one of these channels is busy, while it is NOT. The following is shown on the console: --Called 44 -- Called 36 -- Called 41 -- Called 35 -- Called 38 -- Zap/44-1 is ringing -- Zap/36-1 is ringing -- Zap/41-1 is ringing

Hi, I just came across this annoncement, which is particularly interesting as it is only 25 min away from my place... :-) Anyway, I guess the core of this is targeted at developers mainly. Cheers, Philipp Free Software/Open Source-Telephony-Summit 2004 http://www.guug.de/veranstaltungen/telephony-summit-2004/ http://www.heise.de/newsticker/data/avr-16.12.03-000/ We are happy to announce

Hello- Is it possible to set the CDR record field called "accountcode" from within the dialplan? Or is there another way to cause this field to be set, preferably without using AGI code. Thanks Scott Scott M. Stingel Emerging Voice Technology Inc. Palo Alto, California and London, England www.evtmedia.com

Why not create a listing of the Asterisk resellers. Have a link off the main Digium page and post what asterisk services that particular reseller offers. This way people who are just getting into asterisk know where they can go for commercial support. Maybe the reseller could offer some sort of discounted rate for people who are referred to them through digium? This would boost sales for

Hi I would like to use the Asterisk PBX as part of a phone shop system instead of the usual PBX plus PC. How can I do the the billing in a way that is convinient to the phone shop attendant? Regards Shepherd _________________________________________________________________ Add photos to your messages with MSN 8. Get 2 months FREE*. http://join.msn.com/?page=features/featuredemail

Hi- Because a majority of my customers are in Europe, I've gotten quite used to working with ISDN (PRI) and BRI on a regular basis. Recently one of my customers asked me if I could terminate a few lines locally here in the USA (California), so I called up SBC to enquire as to how much it would cost to install a BRI here. Although the rates were reasonable (except the installation), I got

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.