similar to: Need a recommendation on a good motherboard/processor combination

Here is a SIP phone I haven't seen before. Does anyone have any experience with this one? -----Original Message----- From: George Richardson [mailto:georger@netxusa.com] Sent: Wednesday, April 02, 2003 4:56 PM To: clay@ctitec.com Subject: ipDialog Ethernet SIP Phone $199 pad <http://us.st1.yimg.com/store1.yimg.com/Img/trans_1x1.gif>

I agree, use either SCSI with hardware raid with a battery backed cache or use sata/ide with linux software raid. Linux raid SCSI also works well, but if you go for the scsi drives might as well get the controller too. The "firmware" raid on the cheap sata/ide cards have left me stranded several times, I have had experiences were both an HP and Promise IDE raid controller have SCRAMBLED

Has anyone used TeleFlow? http://downloads-zdnet.com.com/3000-2064-10133790.html?tag=lst-0-23 <http://cl.com.com/Click?q=2b-2FVYINzkpD1yzYJhMJChpWPjQQFR> TeleFlow 5.0 Design and deploy voice applications with ease. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Seems like overnight every motherboard that worked with linux has DROPPED off the face of the earth. Every motherboard I looked at is using the realtek 8111 chipset and a northbridge that is not supported. Example: GIGABYTE GA-970A-DS3, does not work with linux I tried disabling the onboard NIC and using a PCI-E intel card I always use and that would not work either. The north or south bridge

Greetings- I'm attempting to get CentOS 5.5 x86 (yes, very specific version required for specific software usage scenario... don't ask) running on an Intel D425KT mini-ITX motherboard. Everything works fine, with the exception of the onboard ethernet, which is a Realtek RTL8105E chip. The stock CentOS installation attempts to use the r8169 driver, which does not work. I've been around

Hello; I would like to know what's new in motherboard compatible with a Digium card like: Wildcard TE410P or Wildcard TE110P. Thanks every body for helping me!!! :-) //vador

Greetings, I had a quick question about lower memory usage by memdisk. I've read through the mail archives and found a couple of posted questions but unfortunately no answers. I know the documentation states: "MEMDISK simulates a disk by claiming a chunk of high memory for the disk and a (very small - 2K typical) chunk of low (DOS) memory for the driver itself, then hooking the INT 13h

To all.. I was using a Gigabyte motherboard, and the board seems like a bad choice. What do you guys recommend for a decent server board that would use a Dual Core processor and DDR2 ram. I dont want to replace the CPU and Mem i already have, just find a decent board that supportsthe existing.. Thanks, Ryan Nichols -------------- next part -------------- An HTML attachment was scrubbed... URL:

i had such problems on my mini-ITX. when sharing irq's with video or sound card, network traffic during ogg playing (for example on nfs) or quick moving windows crashed the interface. ifconfig down/up resolved the problem. it has been solved for a while now (i couldn't reproduce this problem) i think. regards, OLivier Le Jeudi 12 D?cembre 2002 03:45, The Anarcat a ?crit : >

I'm looking at deploying a new set of servers based around Intel P4 800MHZ FSB processors. Currently I'm looking at the following 2 motherboards and I'm wondering how well supported they are under -STABLE (specificaly the ATA and LAN as well as text mode video) Model Chipset ASUS P4P8X Intel 865P ASUS P4P800 Intel 865PE Also I'm looking for recommendations on Dual Xeon

Has anyone stumbled across an Intel brand motherboard which both works with the 8000 series of CPUs and with CentOS 4/5 out of the box? (by works I mean the NIC/Disk controllers without "fudgery") The DG31 board "kind of" works but unfortunately it has 2 DIMM slots, the realtek NIC isn't supported (don't know why, its just a standard realtek NIC, although it might be

I figured out my previous problem with DIBuilder. However, now I can't seem to get the compiler to emit location information for local variables. Here's how my IR looks: --- define i32 @"\01_main"() { init: %exception1 = alloca i8* %0 = alloca i32 %"bar:Int32" = alloca i32 %1 = alloca i32 %2 = alloca i32* br label %code code:

Not being familiar with chip sets and other factors that "hardware experts" understand, I am perplexed with the multitude of available motherboards. Is there a Web site that can be of help or a "strategy"? My goal is to replace my motherboard with one that is Centos compatible and uses a Pentium 4 in the 2 MHz range. As example, when I go to Mwave, I am presented with

Hello, I am building a home file server and am looking for an ATX mother board that will be supported well with OpenSolaris (onboard SATA controller, network, graphics if any, audio, etc). I decided to go for Intel based boards (socket LGA 775) since it seems like power management is better supported with Intel processors and power efficiency is an important factor. After reading several

I found the problem. The llvm.dbg.declare call must have a !dbg tag, otherwise the location info is not generated. Changing the invocation in my original example to "call void @llvm.dbg.declare(metadata !{i32* %"bar:Int32"}, metadata !13), !dbg !16" causes MC to generate the local location as expected. -Joe On Thu, Dec 29, 2011 at 12:41 PM, Joe Groff <arcata at

Dear R users, has anybody made an attempt to create the soil texture triangle graph in R? For an example see here: http://www.teachingkate.org/images/soiltria.gif I would like to get the lines in black and texture labels in gray to allow for plotting my texture results on top. Any examples or suggestions are very welcome! Thanks in advance, Sander. --

Hi, I have just upgraded my computer to Intel Core i5-4430 Quad Core @ 3.0 GHz (supports VT-d), ASRock B85M Pro4 micro-ATX LGA1150 motherboard (supports VT-d), 8 GB Kingston DDR3-1600 memory and Cooler Master Elite 311 ATX casing (all for SGD$501). I made my computer upgrade on Independence Day 4th July 2013. I have also flashed the UEFI BIOS of ASRock B85M Pro4 motherboard to version 1.50.

Hi all, I'm trying to make multiple lattice contour plots which have the same color key, to allow good comparisons. However, I run into some problems when fitting the plots to the color key. Basically my strategy to tackle this problem was: 1) define a color key for all plots; 2) calculate the variable range for each plot; 3) calculate the range of colors from the color key that correspond

Full_Name: Anantha Prasad Version: 1.1.1 OS: Linux Submission from: (NULL) (199.131.134.30) I am trying to convert some S-PLUS code to R (a tcl/tk application that uses R)... here is the error I got in R (but not in S-PLUS)...so I am wondering if it is a bug. Eg., the foll. extract from a function runs fine in S-PLUS but gives the error: Error in x[[j]] : subscript out of bounds in R code

Hello I have a data array with soil variables (caperf), in which the variable "clay" is factor (as I see entering str(caperf)) . I need to do a regression model, so I need to have arcilla (=clay) as a numeric variable.? For that I have entered as.numeric(as.character(arcilla)) and even entering 'as.numeric(levels(arcilla))[arcilla]'the variable is resting as factor, and the