similar to: Problems with musiconhold

Hi everybody, Firstly I'm going to describe the scenario where I'm working. I use a E400P with Asterisk CVS-05/22/03-11:14:50, and I'm working with asterisk trow AGI scripts (Perl). The configuration of extension.conf is: exten =>_s,1,Answer exten =>_s,2,AGI,script.agi Inside the AGI script is call Dial application as follows: print "EXEC Dial

Dear All, I just setup the Asterisk with E100P which it's no problem in Dial In but I have problem when outdial. The connection method is like this : E1 PRI <-SIGNAL-1-> MaxLink (PBX) <-SIGNAL-2-> E100P <-> Asterisk <--> SIP \-----> Analog PHone Now when I tried to dial out by SIP X-Lite on Windows, it shows me Connect, Trying,

Hi, Some calls I make trough my PSTN asterisk gateway just hangup after some minutes. Even if I'm using sip or iax. I have callprogress=no busydetect=no in my zapata.conf. Anyone help? Or tell me what to look at /var/log/asterisk/debug. I didn't find anything wrong. [endpoint]---iax or sip----[asterisk]----E&M----PSTN. As endpoint I had tested another asterisk box (with a FXS),

Hi Everybody, I am trying to use SIP (Sipura 2000) to connect to Asterisk which then dials out a local number using the Digium E100P. We have purchased the G729 codec licenses from Digium and loaded them into Asterisk successfully. However, the call drops immediately after being answered with the debug error message saying something like: "channel.c:2646 ast_channel_bridge: Didn't get a

Hello, I have an Asterisk box with a TE410P connected to a PRI line and agents with X-Lite installed on the same LAN as the Asterisk server. Sometimes, when I make outbound calls it hangs up as soon as other party tries to picks up the call. Does someone ever experienced this situation? On X-Lite, only G711-ulaw is enabled and here is what i put in sip.conf: [4001] type=friend username=4001

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

It seems consistant after dialing dozens of times that the call that doesn't go through is the one the gets the log message "No echocancellation requested" (chan_zap.c) and the "Scheduleing timer" (channel.c) in the middle of receiving the DTMF tones. I'm now using the T400P card last week very simular problems the the T100P (although I think I was actually loosing

This was submitted to the Dev list last week, but there was no response, and perhaps it wasn't the right group. I am developing an application in which I need asterisk to pass on an incoming call to a separate IVR server. The problem is that asterisk appears to hang up while the IVR is playing back a sequence of recorded voice and systhesized voice prompts. My setup is: Analog line

Hello I have an interesting situaltion and not sure if I am doing something wrong or it is a BUG. I Installed Rhino Channel on T1 line and connected Analog Phone on Rhino's Zap Channels. If i pickup analog phone and hangup without dialing any number , I am getting extra ring after hangup and if i dial any digit than there is no ring on Analog phone after hangup. Log's looks like this

Hello I have an interesting situaltion and not sure if I am doing something wrong or it is a BUG. I Installed Rhino Channel on T1 line and connected Analog Phone on Rhino's Zap Channels. If i pickup analog phone and hangup without dialing any number , I am getting extra ring after hangup and if i dial any digit than there is no ring on Analog phone after hangup. Log's looks like this

Hello I have an interesting situaltion and not sure if I am doing something wrong or it is a BUG. I Installed Rhino Channel on T1 line and connected Analog Phone on Rhino's Zap Channels. When I pickup analog phone and hangup without dialing any number , I am getting extra ring after hangup and if I dial any digit than there is no ring on Analog phone after hangup. Log's looks like this

Hello everybody. I have an customer asterisk 1.0.5 running well since 3 monthes, 2 TDM cards 4 FXO, 4 FXS. Since one week, unable to pass call between Zap and Sip getting the "exception on 15, channel 1" The * box is connected to an eads PBX and it seems that failure started when they make some changes on the PBX. Have someone an idea and what is causisng this failure? Here are the

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Here is a log from a recent call made out on a ZAP channel from a SIP phone inside my network. For some reason, CDR is billing time even though the "busy tone" was detected. It's also logging the call as ANSWERED. Is this normal behavior? Seems a little odd to me. I have this as the first 3 lines of my zapata.conf [channels] busydetect=1 busycount=3 CVS HEAD updated late

Hi all, I've been running Asterisk with a TDM400P for about 6months, no problems. 2 in/outgoing analog lines, one analog phone. Recently I was messing with the XTEN client, got to finagling with things, and not knowing what was wrong I upgraded from 1.0.7 to 1.0.9 (both asterisk + zaptel). I was testing various things, and found everything worked except outgoing calls. So I checked

Well, my faxes passes through asterisk successfully, however I still have some problems about fax reception by rxfax. The softfax answers, and negotiates transmission, however then as some stage of communiation something is wrong. But I have nothing more but this log: Jun 2 00:10:21 DEBUG[16900]: chan_zap.c:4242 zt_read: DTMF digit: * on Zap/10-1 Jun 2 00:10:22 DEBUG[16900]: chan_zap.c:4242

I was wondering how the Dell SC420 will perform under normal office to office communications. We would equip each server with a T1 card to make office to office SIP calls. They will integrate into our existing PBX systems. Does anyone on this list use this hardware currently???? Thanks!

I've got a new setup (different building) where Asterisk is sitting between the PBX and phone company on a E&M T1 line. Mitel PBX <-> Asterisk <-> Phone company Inbound works. Asterisk gets the in-band digits from the phone company and hands the call off to the Mitel just fine. Outbound is weird. Asterisk seems to expect that the mitel will send routing information

Hello, I have problem to make SIP calls, i have asterisk + PC InterP4 + Digium TDM400P here is the content of the sip.conf: [SIP_PROVIDER] type=peer fromuser=testcomclient username=testcomclient secret=testr host=IP_SIP_PROVIDER ;dtmfmode=rfc2833 context=interne canreinvite=no ;allerid=Beer disallow=all allow=ulaw allow=gsm allow=g723.1 ; Asterisk only

The cheap ones on EBay won't work with the SC420 server. I have one and can't make any of the clones work. I do have one TDM40B card for analog stations that works well. The problem with the SC420 is that it won't let you set the interrupts yourself and you end up with interrupts being shared. =============================================================== Message: 26 Date: